Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 54 km/h brakes with a constant deceleration of 6 m/s² until it stops. Find the braking distance s.
v₀ = 54 km/ha = −6 m/s²v = 0
s = m
2.KinematicsHard
A tram starts from rest and accelerates at 1.5 m/s² for 11 s, then runs at constant speed for 17 s, and finally brakes at 4.5 m/s² until it stops. Find the total distance s between the two stops.
a1 = 1.5 m/s²t1 = 11 st2 = 17 sa3 = −4.5 m/s²
s = m
3.Newton’s lawsMedium
A 3 kg block slides down a frictionless slope at 30° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 3 kgθ = 30°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 1 kgm2 = 5 kgμ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 40° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 18 m/sθ = 40°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 40° above horizontal from the top of a 50 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 24 m/sθ = 40°h = 50 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 1 kg ball hangs on a light string of length 1.5 m. It is pulled aside until the string makes 50° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 1 kgL = 1.5 mθ = 50°g = 9.81 m/s²
T = N
8.Work & energyHard
A spring of stiffness 2000 N/m at the bottom of a 25° slope is compressed by 20 cm against a 0.5 kg block and released. The coefficient of kinetic friction between block and slope is 0.15. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 4.5 kg glider moving at 9 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 4.5 kgm2 = 1 kgv1 = 9 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 1900 kg car runs into a parked 1800 kg car. The wrecks lock together and skid 8.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.8. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of oil, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 0.5 mH = 1 mb = 3 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 150 mm to 75 mm. In the wide section the pressure is 190 kPa and the velocity is 2.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A hose with an inner diameter of 40 mm siphons water from an open tank. The highest point C of the hose is 2.5 m above the water surface, and the outlet (open to the air) is 5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 40 mmzC = +2.5 mz2 = −5 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
What volume V does 280 g of CH₄ occupy at 400 kPa and 65 °C? Treat it as an ideal gas.
A reversible (Carnot) heat engine takes in 3900 kJ of heat from a reservoir at 650 °C and rejects 1175 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 650 °CQH = 3900 kJQL = 1175 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is -5 °C outside, delivering 10 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = -5 °CQ̇H = 10 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe open at both ends is 0.6 m long. The speed of sound is 343 m/s. Find the frequency f1 of its fundamental (first harmonic).
v = 343 m/sn = 1L = 0.6 m
f1 = Hz
20.Waves, sound & opticsHard
Light of wavelength 500 nm passes through a single slit 0.1 mm wide. Find the angle θ3 of dark fringe number 3 from the straight-through direction.
λ = 500 nma = 0.1 mmm = 3
θ3 = °
3Solutions
1.Kinematics
Answer: s = 18.75 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 54/3.6 = 15 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 15²/(2·6) = 18.75 m
Answer
s = 18.75 m
2.Kinematics
Answer: s = 401.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 1.5·11 = 16.5 m/s
Distance of each phase
s1 = ½·1.5·11² = 90.75 m
s2 = 16.5·17 = 280.5 m
s3 = 16.5²/(2·4.5) = 30.25 m
Total distance
s = 90.75 + 280.5 + 30.25 = 401.5 m
Answer
s = 401.5 m
3.Newton’s laws
Answer: a = 4.905 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 40° = 13.79 m/s
vy = v0·sin θ = 18·sin 40° = 11.57 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·11.57/9.81 = 2.359 s
Answer
t = 2.359 s
6.Projectile motion
Answer: t = 5.132 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 40° = 18.39 m/s
vy = v0·sin θ = 24·sin 40° = 15.43 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 50 + 15.43·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (15.43 + √(238 + 981))/9.81 = 5.132 s
Answer
t = 5.132 s
7.Work & energy
Answer: T = 16.82 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·1.5·(1 − cos 50°) = 10.51 m²/s²
Forces at the bottom
m·g = 1·9.81 = 9.81 N
T = mg + mv²/L = 9.81 + 1·10.51/1.5 = 16.82 N
Answer
T = 16.82 N
Check: T = mg(3 − 2cos θ) = 16.82 N.
8.Work & energy
Answer: d = 14.6 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 20 cm = 0.2 m
½kx² = ½·2000·0.2² = 40 J
Energy balance along the slope
m·g = 0.5·9.81 = 4.905 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 40/(4.905·(0.4226 + 0.15·0.9063)) = 14.6 m
Answer
d = 14.6 m
9.Momentum & collisions
Answer: v′2 = 14.73 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4.5 − 1)/(4.5 + 1)·9 = 5.727 m/s
v′2 = 2·4.5/(4.5 + 1)·9 = 14.73 m/s
Answer
v′2 = 14.73 m/s
10.Momentum & collisions
Answer: v1 = 22.49 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 3/2 = 2.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·6 = 147.2 kN
Answer
F = 147.2 kN
12.Hydrostatic force
Answer: F = 25.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1/2 = 1 m
A = H·b = 1·3 = 3 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·1·3 = 25.9 kN
Answer
F = 25.9 kN
13.Continuity & Bernoulli
Answer: p2 = 133.3 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 650 + 273.15 = 923.1 K
Reversible heat ratio
TL = TH·QL/QH = 923.1·1175/3900 = 278.1 K = 4.979 °C
Answer
TL = 4.979 °C
18.Heat engines & refrigerators
Answer: Ẇmin = 0.9148 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 10/10.93 = 0.9148 kW
Answer
Ẇmin = 0.9148 kW
19.Waves, sound & optics
Answer: f1 = 285.8 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.6/1 = 1.2 m
Frequency
f = v/λ = 343/1.2 = 285.8 Hz
Answer
f1 = 285.8 Hz
20.Waves, sound & optics
Answer: θ3 = 0.8595 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …