Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 50 km/h brakes with a constant deceleration of 6 m/s² until it stops. Find the braking distance s.
v₀ = 50 km/ha = −6 m/s²v = 0
s = m
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 2.2 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 2.2 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 7 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 7 kgθ = 45°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 10 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 10 kgm2 = 5.5 kgμ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 14 m/sθ = 20°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is thrown from ground level at 34 m/s and 55° above the horizontal. It lands on the flat roof of a building 6 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 34 m/sθ = 55°hroof = 6 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 2000 N/m. A 0.05 kg ball is placed on it and the spring is compressed by 4 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.05 kgk = 2000 N/mx = 4 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 4 kg block is released from rest at height 1 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.3) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 4 kgh = 1 mL = 2 mμ = 0.3k = 2000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 10 g bullet is fired horizontally into a 2.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 7 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 2.5 kgh = 7 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.6 kg ball hits a wall at 22 m/s and bounces straight back at 13 m/s. The contact lasts 20 ms. Find the average force Favg of the wall on the ball.
m = 0.6 kgvin = 22 m/svout = 13 m/sΔt = 20 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 20 mm. The water level is kept 5 m above the orifice and the discharge coefficient is 0.62. Find the flow rate Q. Use g = 9.81 m/s².
d = 20 mmh = 5 mCd = 0.62g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A horizontal venturi meter (inlet 200 mm, throat 100 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 400 mm. The discharge coefficient is 0.97. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 300 °C and a cold reservoir at 30 °C. It takes in 4900 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 300 °CTL = 30 °CQH = 4900 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is 0 °C outside, delivering 4 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = 0 °CQ̇H = 4 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object 1.5 cm tall stands 40 cm in front of a thin converging lens with a focal length of 30 cm. Find the image height hi (negative for an inverted image).
ho = 1.5 cmdo = 40 cmf = 30 cm
hi = cm
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.48 and a cladding with n₂ = 1.46. Find its numerical aperture NA.
n1 = 1.48n2 = 1.46
NA =
3Solutions
1.Kinematics
Answer: s = 16.08 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 13.89²/(2·6) = 16.08 m
Answer
s = 16.08 m
2.Kinematics
Answer: d = 22.35 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(2.2 − t₁)
4.905·t₁² + 343·t₁ − 754.6 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·754.6))/(2·4.905) = 2.135 s
Depth
d = ½·9.81·2.135² = 22.35 m
Answer
d = 22.35 m
3.Newton’s laws
Answer: a = 5.203 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 20° = 13.16 m/s
vy = v0·sin θ = 14·sin 20° = 4.788 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·4.788/9.81 = 0.9762 s
Horizontal distance
x = vx·t = 13.16·0.9762 = 12.84 m
Answer
x = 12.84 m
6.Projectile motion
Answer: x = 106.4 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 19.5 m/s, vy = 27.85 m/s
Time to land on the roof
Larger root: the ball is descending.
6 = 27.85·t − 4.905·t²
t = (27.85 + √(27.85² − 2·9.81·6))/9.81 = 5.454 s
Horizontal distance
x = vx·t = 19.5·5.454 = 106.4 m
Answer
x = 106.4 m
7.Work & energy
Answer: h = 3.262 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 4 cm = 0.04 m
½kx² = ½·2000·0.04² = 1.6 J
Height
m·g = 0.05·9.81 = 0.4905 N
h = ½kx²/(mg) = 1.6/0.4905 = 3.262 m
Answer
h = 3.262 m
8.Work & energy
Answer: v = 2.801 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(1 − 0.3·2) = 15.7 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·0.4) = 2.801 m/s
Answer
v = 2.801 m/s
9.Momentum & collisions
Answer: v = 294.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.07) = 1.172 m/s
Collision
m·v = (m + M)·V → v = (0.01 + 2.5)·1.172/0.01 = 294.2 m/s
Answer
v = 294.2 m/s
10.Momentum & collisions
Answer: Favg = 1050 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.6·(13 + 22) = 21 N·s
Average force
Favg = J/Δt = 21/0.02 = 1050 N
Answer
Favg = 1050 N
11.Hydrostatic force
Answer: F = 159.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2.5/2 = 3.25 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·5 = 159.4 kN
Answer
F = 159.4 kN
12.Hydrostatic force
Answer: F = 67.87 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1/2 = 4.5 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·4.5·1.5 = 67.87 kN
Answer
F = 67.87 kN
13.Continuity & Bernoulli
Answer: Q = 1.929 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·5) = 9.905 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.4 = 49442 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 523.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(400/250)·(523.1/293.1) = 14.28 L
Answer
V2 = 14.28 L
17.Heat engines & refrigerators
Answer: Wmax = 2308 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 300 + 273.15 = 573.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/573.1 = 47.11 %
Maximum work
Wmax = ηmax·QH = 0.4711·4900 = 2308 kJ
Answer
Wmax = 2308 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.2982 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 4/13.42 = 0.2982 kW
Answer
Ẇmin = 0.2982 kW
19.Waves, sound & optics
Answer: hi = −4.5 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/30 − 1/40
di = 120 cm
Magnification and height
m = −120/40 = −3
hi = −3·1.5 = −4.5 cm
Answer
hi = −4.5 cm
20.Waves, sound & optics
Answer: NA = 0.2425
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.