Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 80 km/h brakes with a constant deceleration of 5 m/s² until it stops. How long does braking take? Find t.
v₀ = 80 km/ha = −5 m/s²v = 0
t = s
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 4.6 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 4.6 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 4 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 4 kgθ = 45°μ = 0.1g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5.5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 5 kgm2 = 5.5 kgμ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 30° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 40 m/sθ = 30°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 15° above horizontal from the top of a 40 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 10 m/sθ = 15°h = 40 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 2 kg ball hangs on a light string of length 2 m. It is pulled aside until the string makes 30° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 2 kgL = 2 mθ = 30°g = 9.81 m/s²
T = N
8.Work & energyHard
An 8 kg block starts from rest at the bottom of a 20° slope and is pulled up the slope by a constant force of 70 N parallel to the slope. The coefficient of kinetic friction is 0.3. Find the speed v of the block after it has moved 2 m up the slope.
A 14 kg projectile moving horizontally at 11 m/s explodes into two fragments that move along the same line. The 2 kg fragment continues forwards at 57 m/s. Find the velocity v′2 of the 12 kg fragment (positive in the original direction).
M = 14 kgu = 11 m/sm1 = 2 kgv′1 = 57 m/sm2 = 12 kg
v′2 = m/s
10.Momentum & collisionsHard
A 0.2 kg ball hits a wall at 25 m/s and bounces straight back at 13 m/s. The contact lasts 40 ms. Find the average force Favg of the wall on the ball.
m = 0.2 kgvin = 25 m/svout = 13 m/sΔt = 40 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 2 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 270 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 200 mm, throat 100 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 70 mm. The discharge coefficient is 0.96. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 250 °C and a cold reservoir at 5 °C. Find the highest possible thermal efficiency ηmax.
TH = 250 °CTL = 5 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 20 °C while it is -10 °C outside, delivering 4 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 20 °CTL = -10 °CQ̇H = 4 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 40 cm in front of a thin converging lens with a focal length of 10 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 40 cmf = 10 cm
di = cm
20.Waves, sound & opticsHard
An object is 25 cm in front of a concave mirror with a radius of curvature of 30 cm. Find the magnification m (negative for an inverted image).
do = 25 cmR = 30 cm
m =
3Solutions
1.Kinematics
Answer: t = 4.444 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 80/3.6 = 22.22 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 22.22/5 = 4.444 s
Answer
t = 4.444 s
2.Kinematics
Answer: d = 92.03 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(4.6 − t₁)
4.905·t₁² + 343·t₁ − 1578 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1578))/(2·4.905) = 4.332 s
Depth
d = ½·9.81·4.332² = 92.03 m
Answer
d = 92.03 m
3.Newton’s laws
Answer: a = 6.243 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 40·cos 30° = 34.64 m/s
vy = v0·sin θ = 40·sin 30° = 20 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·20/9.81 = 4.077 s
Horizontal distance
x = vx·t = 34.64·4.077 = 141.2 m
Answer
x = 141.2 m
6.Projectile motion
Answer: t = 3.132 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 10·cos 15° = 9.659 m/s
vy = v0·sin θ = 10·sin 15° = 2.588 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 40 + 2.588·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (2.588 + √(6.699 + 784.8))/9.81 = 3.132 s
Answer
t = 3.132 s
7.Work & energy
Answer: T = 24.88 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·2·(1 − cos 30°) = 5.257 m²/s²
Forces at the bottom
m·g = 2·9.81 = 19.62 N
T = mg + mv²/L = 19.62 + 2·5.257/2 = 24.88 N
Answer
T = 24.88 N
Check: T = mg(3 − 2cos θ) = 24.88 N.
8.Work & energy
Answer: v = 3.243 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 8·9.81 = 78.48 N
mg·sin θ = 26.84 N
μ·mg·cos θ = 22.12 N
Work–energy
½mv² = (70 − 48.97)·2 = 42.07 J
v = √(2·42.07/8) = 3.243 m/s
Answer
v = 3.243 m/s
9.Momentum & collisions
Answer: v′2 = 3.333 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 14·11 = 154 kg·m/s
Momentum after
154 = 2·57 + 12·v′2
v′2 = (154 − 114)/12 = 3.333 m/s
Answer
v′2 = 3.333 m/s
10.Momentum & collisions
Answer: Favg = 190 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.2·(13 + 25) = 7.6 N·s
Average force
Favg = J/Δt = 7.6/0.04 = 190 N
Answer
Favg = 190 N
11.Hydrostatic force
Answer: F = 18.39 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1.5/2 = 1.25 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.25·1.5 = 18.39 kN
Answer
F = 18.39 kN
12.Hydrostatic force
Answer: ycp = 2.818 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2.75·2.25 = 76.48 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.07 = 8652 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 493.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(100/250)·(493.1/303.1) = 1.301 L
Answer
V2 = 1.301 L
17.Heat engines & refrigerators
Answer: ηmax = 46.83 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 250 + 273.15 = 523.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/523.1 = 46.83 %
Answer
ηmax = 46.83 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.4093 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 4/9.772 = 0.4093 kW
Answer
Ẇmin = 0.4093 kW
19.Waves, sound & optics
Answer: di = 13.33 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/10 − 1/40
di = 13.33 cm
Ray diagram
real, on the far side of the lens
Answer
di = 13.33 cm
20.Waves, sound & optics
Answer: m = −1.5
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.