Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 6.5 m/s² until it stops. Find the braking distance s.
v₀ = 90 km/ha = −6.5 m/s²v = 0
s = m
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 32 m/s² for 2.5 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 32 m/s²t1 = 2.5 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 10.5 m/s and comes to rest after 22 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 10.5 m/sd = 22 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 2 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 2 kgm2 = 3.5 kgμ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 22 m/s and 50° above the horizontal towards a wall 19 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 22 m/sθ = 50°x = 19 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 60° above horizontal from the top of a 50 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 35 m/sθ = 60°h = 50 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 10 kg block slides 5 m down a slope at 45° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 10 kgθ = 45°μ = 0.3d = 5 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 2 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3.5 m long (μ = 0.25) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 2 kgh = 3 mL = 3.5 mμ = 0.25k = 1000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 0.5 kg glider moving at 7 m/s makes a perfectly elastic head-on collision with a 1.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 0.5 kgm2 = 1.5 kgv1 = 7 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 17 m/s and bounces straight back at 9 m/s. The contact lasts 40 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.5 kgvin = 17 m/svout = 9 m/sΔt = 40 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 350 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 4 m. At section 1 the pressure is 240 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 650 °C and a cold reservoir at 10 °C. Find the highest possible thermal efficiency ηmax.
TH = 650 °CTL = 10 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -25 °C in a kitchen at 28 °C, removing heat from the cold space at 4.5 kW. Find the highest possible coefficient of performance COPmax.
TH = 28 °CTL = -25 °CQ̇L = 4.5 kW
COPmax =
19.Waves, sound & opticsMedium
A pipe closed at one end is 0.5 m long. The speed of sound is 343 m/s. Find the frequency f5 of its harmonic number 5.
v = 343 m/sn = 5L = 0.5 m
f5 = Hz
20.Waves, sound & opticsHard
Light of wavelength 600 nm passes through a single slit 0.08 mm wide. Find the angle θ3 of dark fringe number 3 from the straight-through direction.
λ = 600 nma = 0.08 mmm = 3
θ3 = °
3Solutions
1.Kinematics
Answer: s = 48.08 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 25²/(2·6.5) = 48.08 m
Answer
s = 48.08 m
2.Kinematics
Answer: hmax = 426.2 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 32·2.5 = 80 m/s
h₁ = ½·32·2.5² = 100 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 80²/(2·9.81) = 326.2 m
hmax = 100 + 326.2 = 426.2 m
Answer
hmax = 426.2 m
3.Newton’s laws
Answer: μ = 0.2554
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 10.5²/(2·22) = 2.506 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 2.506/9.81 = 0.2554
Answer
μ = 0.2554
4.Newton’s laws
Answer: T = 15.61 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 22·cos 50° = 14.14 m/s
t = x/vx = 19/14.14 = 1.344 s
Height at that time
y = 16.85·1.344 − ½·9.81·1.344² = 13.79 m
Answer
y = 13.79 m
The ball is still rising at the wall.
6.Projectile motion
Answer: t = 7.533 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 35·cos 60° = 17.5 m/s
vy = v0·sin θ = 35·sin 60° = 30.31 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 50 + 30.31·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (30.31 + √(918.7 + 981))/9.81 = 7.533 s
Answer
t = 7.533 s
7.Work & energy
Answer: Wf = 104.1 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 98.1·0.7071 = 69.37 N
F = μN = 0.3·69.37 = 20.81 N
Work against friction
Wf = F·d = 20.81·5 = 104.1 J
Answer
Wf = 104.1 J
8.Work & energy
Answer: v = 6.457 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(3 − 0.25·3.5) = 41.69 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·2.125) = 6.457 m/s
Answer
v = 6.457 m/s
9.Momentum & collisions
Answer: v′2 = 3.5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (0.5 − 1.5)/(0.5 + 1.5)·7 = −3.5 m/s
v′2 = 2·0.5/(0.5 + 1.5)·7 = 3.5 m/s
Answer
v′2 = 3.5 m/s
10.Momentum & collisions
Answer: J = 13 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(9 + 17) = 13 N·s
Answer
J = 13 N·s
11.Hydrostatic force
Answer: F = 183.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2.5/2 = 3.75 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.75·5 = 183.9 kN
Answer
F = 183.9 kN
12.Hydrostatic force
Answer: F = 77.25 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1.5/2 = 1.75 m
A = H·b = 1.5·3 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·4.5 = 77.25 kN
Answer
F = 77.25 kN
13.Continuity & Bernoulli
Answer: p2 = 327 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 313.1 K, T2 = 503.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(250/750)·(503.1/313.1) = 5.356 L
Answer
V2 = 5.356 L
17.Heat engines & refrigerators
Answer: ηmax = 69.33 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 283.1/923.1 = 69.33 %
Answer
ηmax = 69.33 %
18.Heat engines & refrigerators
Answer: COPmax = 4.682
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·0.5/5 = 0.4 m
Frequency
f = v/λ = 343/0.4 = 857.5 Hz
Answer
f5 = 857.5 Hz
20.Waves, sound & optics
Answer: θ3 = 1.289 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …