Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 8 m/s² until it stops. Find the braking distance s.
v₀ = 90 km/ha = −8 m/s²v = 0
s = m
2.KinematicsHard
Ball A is dropped from rest from a height of 60 m. At the same instant ball B is thrown straight up from the ground directly below at 22 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 60 mv0B = 22 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
Masses of 7.5 kg and 3 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the acceleration a of the masses.
m1 = 7.5 kgm2 = 3 kgg = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 5.5 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 5.5 m/sθ = 25°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 12 m/sθ = 20°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is thrown from ground level at 38 m/s and 40° above the horizontal. It lands on the flat roof of a building 16 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 38 m/sθ = 40°hroof = 16 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 2000 N/m. A 0.15 kg ball is placed on it and the spring is compressed by 3 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.15 kgk = 2000 N/mx = 3 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 2.5 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.1) and then runs onto a spring (k = 5000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2.5 kgh = 4 mL = 1.5 mμ = 0.1k = 5000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 5 g bullet is fired horizontally into a 1.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 17 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 1.5 kgh = 17 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 8 m/s and bounces straight back at 4 m/s. The contact lasts 10 ms. Find the average force Favg of the wall on the ball.
m = 0.55 kgvin = 8 m/svout = 4 m/sΔt = 10 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 400 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A hose with an inner diameter of 32 mm siphons water from an open tank. The highest point C of the hose is 1.5 m above the water surface, and the outlet (open to the air) is 1.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 32 mmzC = +1.5 mz2 = −1.5 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
A tank of 50 L contains 330 g of Ar at 55 °C. Treat it as an ideal gas and find the pressure P.
A heat engine works between a hot reservoir at 450 °C and a cold reservoir at 5 °C. It takes in 600 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 450 °CTL = 5 °CQH = 600 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat engine takes in 4300 kJ of heat from a reservoir at 500 °C, produces 2150 kJ of work and rejects the rest to a reservoir at 20 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 500 °CTL = 20 °CQH = 4300 kJW = 2150 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
A pipe open at both ends is 0.5 m long. The speed of sound is 343 m/s. Find the frequency f5 of its harmonic number 5.
v = 343 m/sn = 5L = 0.5 m
f5 = Hz
20.Waves, sound & opticsHard
A diffraction grating has 600 lines per millimetre. Light of wavelength 450 nm falls on it at right angles. What is the highest order mmax of bright maximum that can be seen?
N = 600 mm⁻¹λ = 450 nm
mmax =
3Solutions
1.Kinematics
Answer: s = 39.06 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 25²/(2·8) = 39.06 m
Answer
s = 39.06 m
2.Kinematics
Answer: t = 2.727 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
60 − ½g·t² = 22·t − ½g·t² → t = 60/22 = 2.727 s
Answer
t = 2.727 s
3.Newton’s laws
Answer: a = 4.204 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (7.5 − 3)·9.81/(7.5 + 3) = 4.204 m/s²
Answer
a = 4.204 m/s²
4.Newton’s laws
Answer: d = 2.76 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 25° + 0.15·cos 25°) = 5.48 m/s²
Distance
d = v₀²/(2a) = 5.5²/(2·5.48) = 2.76 m
Answer
d = 2.76 m
5.Projectile motion
Answer: H = 0.8586 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 12·cos 20° = 11.28 m/s
vy = v0·sin θ = 12·sin 20° = 4.104 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 4.104²/(2·9.81) = 0.8586 m
Answer
H = 0.8586 m
6.Projectile motion
Answer: x = 122.4 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 29.11 m/s, vy = 24.43 m/s
Time to land on the roof
Larger root: the ball is descending.
16 = 24.43·t − 4.905·t²
t = (24.43 + √(24.43² − 2·9.81·16))/9.81 = 4.204 s
Horizontal distance
x = vx·t = 29.11·4.204 = 122.4 m
Answer
x = 122.4 m
7.Work & energy
Answer: h = 0.6116 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 3 cm = 0.03 m
½kx² = ½·2000·0.03² = 0.9 J
Height
m·g = 0.15·9.81 = 1.472 N
h = ½kx²/(mg) = 0.9/1.472 = 0.6116 m
Answer
h = 0.6116 m
8.Work & energy
Answer: x = 19.43 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 24.53·(4 − 0.1·1.5) = 94.42 J
Maximum compression
½kx² = 94.42 → x = √(2·94.42/5000) = 0.1943 m = 19.43 cm
Answer
x = 19.43 cm
9.Momentum & collisions
Answer: v = 549.7 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.17) = 1.826 m/s
Collision
m·v = (m + M)·V → v = (0.005 + 1.5)·1.826/0.005 = 549.7 m/s
Answer
v = 549.7 m/s
10.Momentum & collisions
Answer: Favg = 660 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(4 + 8) = 6.6 N·s
Average force
Favg = J/Δt = 6.6/0.01 = 660 N
Answer
Favg = 660 N
11.Hydrostatic force
Answer: F = 137.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2/2 = 3.5 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·4 = 137.3 kN
Answer
F = 137.3 kN
12.Hydrostatic force
Answer: F = 193.1 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.25·3.75 = 193.1 kN
Answer
F = 193.1 kN
13.Continuity & Bernoulli
Answer: p2 = 377 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 423.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(150/200)·(423.1/303.1) = 20.94 L
Answer
V2 = 20.94 L
17.Heat engines & refrigerators
Answer: Wmax = 369.2 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 450 + 273.15 = 723.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/723.1 = 61.54 %
Maximum work
Wmax = ηmax·QH = 0.6154·600 = 369.2 kJ
Answer
Wmax = 369.2 kJ
18.Heat engines & refrigerators
Answer: Sgen = 1.772 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 4300 − 2150 = 2150 kJ
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
TL = 20 + 273.15 = 293.1 K
Entropy changes of the reservoirs
ΔSH = −4300/773.1 = −5.562 kJ/K
ΔSL = 2150/293.1 = 7.334 kJ/K
Sgen = 7.334 − 5.562 = 1.772 kJ/K
Answer
Sgen = 1.772 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: f5 = 1715 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.5/5 = 0.2 m
Frequency
f = v/λ = 343/0.2 = 1715 Hz
Answer
f5 = 1715 Hz
20.Waves, sound & optics
Answer: mmax = 3
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …