Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 3.5 m/s² along a runway. Find its speed v after 1600 m.
v₀ = 0a = 3.5 m/s²s = 1600 m
v = m/s
2.KinematicsHard
A ball is thrown straight up at 16 m/s from the edge of a roof 40 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 16 m/sh₀ = 40 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
Masses of 7 kg and 3.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the acceleration a of the masses.
m1 = 7 kgm2 = 3.5 kgg = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 3.5 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 3.5 m/sθ = 25°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is kicked from level ground at 40 m/s and 70° above the horizontal towards a wall 73 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 40 m/sθ = 70°x = 73 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 30° above horizontal from the top of a 30 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 22 m/sθ = 30°h = 30 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 1200 kg car drives up an 8° slope at a constant 90 km/h. Air resistance and rolling resistance together amount to 700 N. Find the power P the wheels must deliver, in kW.
A spring of stiffness 2000 N/m at the bottom of a 15° slope is compressed by 20 cm against a 0.5 kg block and released. The coefficient of kinetic friction between block and slope is 0.1. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 1200 kg car moving at 9 m/s runs into a stationary 500 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 1200 kgv1 = 9 m/sm2 = 500 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
A 0.6 kg ball hits a wall at 30 m/s and bounces straight back at 12 m/s. The contact lasts 50 ms. Find the average force Favg of the wall on the ball.
m = 0.6 kgvin = 30 m/svout = 12 m/sΔt = 50 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 3 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of seawater, with its top edge 1.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 150 mm to 40 mm. In the wide section the pressure is 210 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 8 m. At section 1 the pressure is 370 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 450 °C and rejects heat to the surroundings at 20 °C. Its actual thermal efficiency is 30%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 450 °CTL = 20 °Cη = 30%
ηII = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is -10 °C outside, delivering 11 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = -10 °CQ̇H = 11 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
Light travels in diamond (n = 2.42) towards a flat boundary with flint glass (n = 1.62). Find the critical angle θc beyond which it is totally reflected.
n1 = 2.42n2 = 1.62
θc = °
20.Waves, sound & opticsHard
Light of wavelength 650 nm falls on two slits 0.4 mm apart. The screen is 1 m away. Find the distance y2 from the central bright fringe to bright fringe number 2.
λ = 650 nmd = 0.4 mmL = 1 mm = 2
y2 = mm
3Solutions
1.Kinematics
Answer: v = 105.8 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·3.5·1600) = 105.8 m/s
Answer
v = 105.8 m/s
(381 km/h)
2.Kinematics
Answer: hmax = 53.05 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 16²/(2·9.81) = 13.05 m
Height above the ground
hmax = 40 + 13.05 = 53.05 m
Answer
hmax = 53.05 m
3.Newton’s laws
Answer: a = 3.27 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (7 − 3.5)·9.81/(7 + 3.5) = 3.27 m/s²
Answer
a = 3.27 m/s²
4.Newton’s laws
Answer: d = 1.118 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 25° + 0.15·cos 25°) = 5.48 m/s²
Distance
d = v₀²/(2a) = 3.5²/(2·5.48) = 1.118 m
Answer
d = 1.118 m
5.Projectile motion
Answer: y = 60.91 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 40·cos 70° = 13.68 m/s
t = x/vx = 73/13.68 = 5.336 s
Height at that time
y = 37.59·5.336 − ½·9.81·5.336² = 60.91 m
Answer
y = 60.91 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: x = 73.1 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 22·cos 30° = 19.05 m/s
vy = v0·sin θ = 22·sin 30° = 11 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 30 + 11·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (11 + √(121 + 588.6))/9.81 = 3.837 s
Horizontal distance
x = vx·t = 19.05·3.837 = 73.1 m
Answer
x = 73.1 m
7.Work & energy
Answer: P = 58.46 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 1200·9.81 = 11772 N
mg·sin θ = 11772·sin 8° = 1638 N
F = 1638 + 700 = 2338 N
Power
v = 90/3.6 = 25 m/s
P = F·v = 2338·25 = 58459 W = 58.46 kW
Answer
P = 58.46 kW
8.Work & energy
Answer: d = 22.95 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 20 cm = 0.2 m
½kx² = ½·2000·0.2² = 40 J
Energy balance along the slope
m·g = 0.5·9.81 = 4.905 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 40/(4.905·(0.2588 + 0.1·0.9659)) = 22.95 m
Answer
d = 22.95 m
9.Momentum & collisions
Answer: ΔK/K = 29.41 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1200·9/1700 = 6.353 m/s
Kinetic energy before and after
Kbefore = ½·1200·9² = 48600 J
Kafter = ½·1700·6.353² = 34306 J
Fraction lost
ΔK/K = 14294/48600 = 29.41 %
Answer
ΔK/K = 29.41 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: Favg = 504 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.6·(12 + 30) = 25.2 N·s
Average force
Favg = J/Δt = 25.2/0.05 = 504 N
Answer
Favg = 504 N
11.Hydrostatic force
Answer: F = 132.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 3/2 = 4.5 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.5·3 = 132.4 kN
Answer
F = 132.4 kN
12.Hydrostatic force
Answer: ycp = 2.939 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2.75·7.5 = 207.4 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 333.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(250/500)·(333.1/288.1) = 1.156 L
Answer
V2 = 1.156 L
17.Heat engines & refrigerators
Answer: ηII = 50.45 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 450 + 273.15 = 723.1 K
TL = 20 + 273.15 = 293.1 K
Carnot efficiency
ηCarnot = 1 − 293.1/723.1 = 59.46 %
Second-law efficiency
ηII = η/ηCarnot = 30/59.46 = 50.45 %
Answer
ηII = 50.45 %
18.Heat engines & refrigerators
Answer: Ẇmin = 1.193 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 11/9.223 = 1.193 kW
Answer
Ẇmin = 1.193 kW
19.Waves, sound & optics
Answer: θc = 42.02 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.62/2.42 = 0.6694
Critical angle
θc = arcsin(0.6694) = 42.02°
Answer
θc = 42.02°
20.Waves, sound & optics
Answer: y2 = 3.25 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …