Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 29 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 5 m/s². How long does it take the police car to catch up? Find t.
vcar = 29 m/sapolice = 5 m/s²v0,police = 0
t = s
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 4.7 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 4.7 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 13 kg block slides down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 13 kgθ = 20°μ = 0.1g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 10 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 10 kgm2 = 4 kgμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 30° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 28 m/sθ = 30°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 24 m/s and 45° above the horizontal from the top of a 15 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 24 m/sθ = 45°h = 15 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A car travelling at 90 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.8. Find the stopping distance d.
v = 90 km/hμ = 0.8g = 9.81 m/s²
d = m
8.Work & energyHard
A 5 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2.5 m long (μ = 0.25) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 5 kgh = 4 mL = 2.5 mμ = 0.25k = 1500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 3 kg glider moving at 2 m/s makes a perfectly elastic head-on collision with a 2.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3 kgm2 = 2.5 kgv1 = 2 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
At a crossing a 1000 kg car travelling east at 14 m/s collides with a 900 kg car travelling north at 22 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 1000 kgv1 = 14 m/s (E)m2 = 900 kgv2 = 22 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 2 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 2 mH = 1 mb = 2 mρ = 1260 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal venturi meter with an inlet diameter of 80 mm and a throat diameter of 40 mm. The pressure at the inlet is 48 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 50 mm and a gauge pressure of 130 kPa. The nozzle exit diameter is 25 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A reversible refrigerator keeps a cold room at 5 °C by removing 4 kW of heat, and rejects heat to the surroundings at 40 °C. Find the rate Q̇H at which it rejects heat.
TL = 5 °CTH = 40 °CQ̇L = 4 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -10 °C in a kitchen at 25 °C, removing heat from the cold space at 1 kW. Find the minimum power input Ẇmin.
TH = 25 °CTL = -10 °CQ̇L = 1 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A source of 1200 Hz moves at 30 m/s towards a stationary observer. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 1200 Hzv = 343 m/svs = 30 m/s
f′ = Hz
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.48 and a cladding with n₂ = 1.47. Find its numerical aperture NA.
n1 = 1.48n2 = 1.47
NA =
3Solutions
1.Kinematics
Answer: t = 11.6 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·29/5 = 11.6 s
Answer
t = 11.6 s
At that moment the police car moves at 2v = 58 m/s.
2.Kinematics
Answer: d = 95.85 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(4.7 − t₁)
4.905·t₁² + 343·t₁ − 1612 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1612))/(2·4.905) = 4.421 s
Depth
d = ½·9.81·4.421² = 95.85 m
Answer
d = 95.85 m
3.Newton’s laws
Answer: a = 2.433 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 30° = 24.25 m/s
vy = v0·sin θ = 28·sin 30° = 14 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·14/9.81 = 2.854 s
Horizontal distance
x = vx·t = 24.25·2.854 = 69.21 m
Answer
x = 69.21 m
6.Projectile motion
Answer: α = 54.88 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 24·cos 45° = 16.97 m/s
vy0 = 24·sin 45° = 16.97 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(16.97² + 2·9.81·15) = 24.13 m/s
Impact angle
tan α = vy/vx = 24.13/16.97 → α = 54.88°
Answer
α = 54.88°
7.Work & energy
Answer: d = 39.82 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 90/3.6 = 25 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 25²/(2·0.8·9.81) = 39.82 m
Answer
d = 39.82 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: x = 46.98 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(4 − 0.25·2.5) = 165.5 J
Maximum compression
½kx² = 165.5 → x = √(2·165.5/1500) = 0.4698 m = 46.98 cm
Answer
x = 46.98 cm
9.Momentum & collisions
Answer: v′2 = 2.182 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3 − 2.5)/(3 + 2.5)·2 = 0.1818 m/s
v′2 = 2·3/(3 + 2.5)·2 = 2.182 m/s
Answer
v′2 = 2.182 m/s
10.Momentum & collisions
Answer: θ = 54.74 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 1000·14 = 14000 kg·m/s
py = 900·22 = 19800 kg·m/s
Direction
tan θ = py/px = 1.414 → θ = 54.74°
Answer
θ = 54.74°
11.Hydrostatic force
Answer: F = 79.71 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2.5/2 = 3.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·2.5 = 79.71 kN
Answer
F = 79.71 kN
12.Hydrostatic force
Answer: ycp = 2.533 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1/2 = 2.5 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2.5·2 = 61.8 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(40/80)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 25/50 = 0.5
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·130000/(1000·0.9375)) = 16.65 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 16.65²/(2·9.81) = 14.14 m
Answer
H = 14.14 m
15.Ideal gas law
Answer: V = 13.03 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 70/32 = 2.188 mol
T = 85 + 273.15 = 358.1 K
Volume
V = nRT/P = 2.188·8.314·358.1/500 = 13.03 L
Answer
V = 13.03 L
16.Ideal gas law
Answer: V2 = 13.97 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 503.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(200/500)·(503.1/288.1) = 13.97 L
Answer
V2 = 13.97 L
17.Heat engines & refrigerators
Answer: Q̇H = 4.503 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 40 + 273.15 = 313.1 K
TL = 5 + 273.15 = 278.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 4·313.1/278.1 = 4.503 kW
Answer
Q̇H = 4.503 kW
Power input: Ẇ = 0.5033 kW.
18.Heat engines & refrigerators
Answer: Ẇmin = 0.133 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 1/7.519 = 0.133 kW
Answer
Ẇmin = 0.133 kW
19.Waves, sound & optics
Answer: f′ = 1315 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.