Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 3.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 90 km/ha = −3.5 m/s²v = 0
t = s
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 34 m/s² for 2 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 34 m/s²t1 = 2 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 40 kg box is pushed up a ramp at 35° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.4. Use g = 9.81 m/s². Find the pushing force F.
m = 40 kgθ = 35°μ = 0.4g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A 9 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 9 kgm2 = 4 kgμ = 0.3g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 30° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 14 m/sθ = 30°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 15 m/s and 40° above the horizontal from the top of a 50 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 15 m/sθ = 40°h = 50 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A block slides from rest down a slope at 15° to the horizontal. The coefficient of kinetic friction is 0.1. Find its speed v after it has slid 13 m along the slope.
θ = 15°μ = 0.1d = 13 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
An 8 kg block rests on a rough horizontal table (μ = 0.2). A light string runs from it over a smooth pulley at the edge of the table to a hanging 3 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 2 m.
m1 = 8 kgm2 = 3 kgμ = 0.2d = 2 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 5 kg glider moving at 9 m/s makes a perfectly elastic head-on collision with a 0.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 5 kgm2 = 0.5 kgv1 = 9 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 10 g bullet is fired horizontally into a 4 kg block hanging from light strings 1.9 m long, and stays in it. The strings swing out to a largest angle of 35° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 4 kgL = 1.9 mθ = 35°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
A pitot-static tube in a water pipe reads a difference of 11 kPa between the stagnation pressure and the static pressure. Find the water velocity v at the tip.
p0 − p = 11 kPaρ = 1000 kg/m³
v = m/s
14.Continuity & BernoulliHard
A hose with an inner diameter of 25 mm siphons water from an open tank. The highest point C of the hose is 2.5 m above the water surface, and the outlet (open to the air) is 4.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the absolute pressure pC at point C. The atmospheric pressure is 101.3 kPa.
A reversible refrigerator keeps a cold room at 0 °C by removing 8 kW of heat, and rejects heat to the surroundings at 30 °C. Find the rate Q̇H at which it rejects heat.
TL = 0 °CTH = 30 °CQ̇L = 8 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 130 kW of heat from a source at 400 °C and rejects heat to the surroundings at 25 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -10 °C and also rejects heat to the surroundings at 25 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 400 °CT0 = 25 °CTL = -10 °CQ̇H = 130 kW
Q̇L = kW
19.Waves, sound & opticsMedium
An object stands 10 cm in front of a thin converging lens with a focal length of 12 cm. Find the magnification m (negative for an inverted image).
do = 10 cmf = 12 cm
m =
20.Waves, sound & opticsHard
An object is 20 cm in front of a concave mirror with a radius of curvature of 16 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 20 cmR = 16 cm
di = cm
3Solutions
1.Kinematics
Answer: t = 7.143 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 25/3.5 = 7.143 s
Answer
t = 7.143 s
2.Kinematics
Answer: hmax = 303.7 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 34·2 = 68 m/s
h₁ = ½·34·2² = 68 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 68²/(2·9.81) = 235.7 m
hmax = 68 + 235.7 = 303.7 m
Answer
hmax = 303.7 m
3.Newton’s laws
Answer: F = 353.6 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 225.1 + 128.6 = 353.6 N
Answer
F = 353.6 N
4.Newton’s laws
Answer: T = 35.32 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 30° = 12.12 m/s
vy = v0·sin θ = 14·sin 30° = 7 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·7/9.81 = 1.427 s
Horizontal distance
x = vx·t = 12.12·1.427 = 17.3 m
Answer
x = 17.3 m
6.Projectile motion
Answer: α = 70.68 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 15·cos 40° = 11.49 m/s
vy0 = 15·sin 40° = 9.642 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(9.642² + 2·9.81·50) = 32.77 m/s
Impact angle
tan α = vy/vx = 32.77/11.49 → α = 70.68°
Answer
α = 70.68°
7.Work & energy
Answer: v = 6.433 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·13·(0.2588 − 0.1·0.9659)) = 6.433 m/s
Answer
v = 6.433 m/s
8.Work & energy
Answer: v = 2.235 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 29.43·2 = 58.86 J
μ·m₁g·d = 0.2·78.48·2 = 31.39 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 27.47 → v = √(2·27.47/11) = 2.235 m/s
Answer
v = 2.235 m/s
9.Momentum & collisions
Answer: v′2 = 16.36 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (5 − 0.5)/(5 + 0.5)·9 = 7.364 m/s
v′2 = 2·5/(5 + 0.5)·9 = 16.36 m/s
Answer
v′2 = 16.36 m/s
10.Momentum & collisions
Answer: v = 1041 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.9·(1 − cos 35°) = 0.3436 m
Speed after impact
V = √(2·9.81·0.3436) = 2.596 m/s
Collision
v = (m + M)·V/m = 4.01·2.596/0.01 = 1041 m/s
Answer
v = 1041 m/s
11.Hydrostatic force
Answer: F = 143.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1.5/2 = 3.25 m
A = H·b = 1.5·3 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·4.5 = 143.5 kN
Answer
F = 143.5 kN
12.Hydrostatic force
Answer: ycp = 5.349 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.25·5 = 257.5 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·11000/1000) = 4.69 m/s
Answer
v = 4.69 m/s
14.Continuity & Bernoulli
Answer: pC = 32.63 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
If this pressure falls to the vapour pressure of the water, the siphon stops working.
15.Ideal gas law
Answer: P = 5410 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 460/4.003 = 114.9 mol
T = 10 + 273.15 = 283.1 K
Pressure
P = nRT/V = 114.9·8.314·283.1/0.05 = 5410 kPa
Answer
P = 5410 kPa
16.Ideal gas law
Answer: V2 = 2.398 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 353.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(250/650)·(353.1/283.1) = 2.398 L
Answer
V2 = 2.398 L
17.Heat engines & refrigerators
Answer: Q̇H = 8.879 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 30 + 273.15 = 303.1 K
TL = 0 + 273.15 = 273.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 8·303.1/273.1 = 8.879 kW
Answer
Q̇H = 8.879 kW
Power input: Ẇ = 0.8786 kW.
18.Heat engines & refrigerators
Answer: Q̇L = 544.5 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
T0 = 25 + 273.15 = 298.1 K
TL = -10 + 273.15 = 263.1 K
Engine work
η = 1 − 298.1/673.1 = 0.5571
Ẇ = 0.5571·130 = 72.42 kW
Heat removed by the refrigerator
COPR = 263.1/(298.1 − 263.1) = 7.519
Q̇L = 7.519·72.42 = 544.5 kW
Answer
Q̇L = 544.5 kW
19.Waves, sound & optics
Answer: m = 6
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/12 − 1/10
di = −60 cm
Magnification
m = −di/do = −(−60)/10 = 6
Answer
m = 6
20.Waves, sound & optics
Answer: di = 13.33 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.