Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 260 km/h to take off and the usable runway is 1500 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 260 km/hs = 1500 m
a = m/s²
2.KinematicsHard
A ball is thrown straight up at 5 m/s from the edge of a roof 20 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 5 m/sh₀ = 20 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 13 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 13 kgθ = 30°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 9 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 6 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 9 kgm2 = 6 kgμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 45° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 32 m/sθ = 45°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 60° above horizontal from the top of a 30 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 21 m/sθ = 60°h = 30 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 2000 kg car drives up a 2° slope at a constant 36 km/h. Air resistance and rolling resistance together amount to 450 N. Find the power P the wheels must deliver, in kW.
A 2 kg block starts from rest at the bottom of a 35° slope and is pulled up the slope by a constant force of 25 N parallel to the slope. The coefficient of kinetic friction is 0.15. Find the speed v of the block after it has moved 4 m up the slope.
A 4 kg glider moving at 12 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 4 kgm2 = 1 kgv1 = 12 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 5 g bullet is fired horizontally into a 3 kg block hanging from light strings 1.5 m long, and stays in it. The strings swing out to a largest angle of 35° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 3 kgL = 1.5 mθ = 35°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 3 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows at 12 L/s through a horizontal pipe that narrows from 150 mm to 75 mm. The pressure in the narrow section is 250 kPa. Ignoring losses, find the pressure p1 in the wide section.
Water flows up through a pipe that narrows from 200 mm to 50 mm while rising 2 m. At section 1 the pressure is 390 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 425 °C and a cold reservoir at 40 °C. Find the highest possible thermal efficiency ηmax.
TH = 425 °CTL = 40 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is -5 °C outside, delivering 15 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 21 °CTL = -5 °CQ̇H = 15 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A string fixed at both ends must have its harmonic number 4 at 600 Hz; waves travel on it at 240 m/s. Find its length L.
v = 240 m/sn = 4f4 = 600 Hz
L = m
20.Waves, sound & opticsHard
Light of wavelength 550 nm falls on two slits 0.15 mm apart. The screen is 1 m away. Find the distance y2 from the central bright fringe to bright fringe number 2.
λ = 550 nmd = 0.15 mmL = 1 mm = 2
y2 = mm
3Solutions
1.Kinematics
Answer: a = 1.739 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 260/3.6 = 72.22 m/s
Acceleration
a = v²/(2s) = 72.22²/(2·1500) = 1.739 m/s²
Answer
a = 1.739 m/s²
2.Kinematics
Answer: t = 2.592 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−20 = 5·t − ½·9.81·t²
4.905·t² − 5·t − 20 = 0
Solve the quadratic
Only the positive root is physical.
t = (5 + √(5² + 2·9.81·20))/9.81 = 2.592 s
Answer
t = 2.592 s
3.Newton’s laws
Answer: a = 3.631 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 32·cos 45° = 22.63 m/s
vy = v0·sin θ = 32·sin 45° = 22.63 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·22.63/9.81 = 4.613 s
Horizontal distance
x = vx·t = 22.63·4.613 = 104.4 m
Answer
x = 104.4 m
6.Projectile motion
Answer: t = 4.945 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 21·cos 60° = 10.5 m/s
vy = v0·sin θ = 21·sin 60° = 18.19 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 30 + 18.19·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (18.19 + √(330.8 + 588.6))/9.81 = 4.945 s
Answer
t = 4.945 s
7.Work & energy
Answer: P = 11.35 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 2000·9.81 = 19620 N
mg·sin θ = 19620·sin 2° = 684.7 N
F = 684.7 + 450 = 1135 N
Power
v = 36/3.6 = 10 m/s
P = F·v = 1135·10 = 11347 W = 11.35 kW
Answer
P = 11.35 kW
8.Work & energy
Answer: v = 6.734 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 2·9.81 = 19.62 N
mg·sin θ = 11.25 N
μ·mg·cos θ = 2.411 N
Work–energy
½mv² = (25 − 13.66)·4 = 45.34 J
v = √(2·45.34/2) = 6.734 m/s
Answer
v = 6.734 m/s
9.Momentum & collisions
Answer: v′2 = 19.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4 − 1)/(4 + 1)·12 = 7.2 m/s
v′2 = 2·4/(4 + 1)·12 = 19.2 m/s
Answer
v′2 = 19.2 m/s
10.Momentum & collisions
Answer: v = 1387 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.5·(1 − cos 35°) = 0.2713 m
Speed after impact
V = √(2·9.81·0.2713) = 2.307 m/s
Collision
v = (m + M)·V/m = 3.005·2.307/0.005 = 1387 m/s
Answer
v = 1387 m/s
11.Hydrostatic force
Answer: F = 103 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·3 = 103 kN
Answer
F = 103 kN
12.Hydrostatic force
Answer: ycp = 5.636 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 3/2 = 5.5 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.5·4.5 = 242.8 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 425 + 273.15 = 698.1 K
TL = 40 + 273.15 = 313.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 313.1/698.1 = 55.15 %
Answer
ηmax = 55.15 %
18.Heat engines & refrigerators
Answer: Ẇmin = 1.326 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 15/11.31 = 1.326 kW
Answer
Ẇmin = 1.326 kW
19.Waves, sound & optics
Answer: L = 0.8 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 240/600 = 0.4 m
Length
L = nλ/2 = 4·0.4/2 = 0.8 m
Answer
L = 0.8 m
20.Waves, sound & optics
Answer: y2 = 7.333 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …