Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 72 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 72 km/ha = −4.5 m/s²v = 0
t = s
2.KinematicsHard
A tram starts from rest and accelerates at 1.5 m/s² for 5 s, then runs at constant speed for 21 s, and finally brakes at 2.5 m/s² until it stops. Find the total distance s between the two stops.
a1 = 1.5 m/s²t1 = 5 st2 = 21 sa3 = −2.5 m/s²
s = m
3.Newton’s lawsMedium
A 3 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 3 kgθ = 25°μ = 0.1g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 9.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2.5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 9.5 kgm2 = 2.5 kgμ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 40 m/s and 20° above the horizontal towards a wall 73 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 40 m/sθ = 20°x = 73 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 15° above horizontal from the top of a 50 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 29 m/sθ = 15°h = 50 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 1200 kg car drives up an 8° slope at a constant 36 km/h. Air resistance and rolling resistance together amount to 500 N. Find the power P the wheels must deliver, in kW.
A 5 kg block is released from rest at height 2 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.25) and then runs onto a spring (k = 800 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 5 kgh = 2 mL = 1.5 mμ = 0.25k = 800 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1600 kg car moving at 17 m/s runs into a stationary 1900 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 1600 kgv1 = 17 m/sm2 = 1900 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
A 12 g bullet is fired horizontally into a 1 kg block hanging from light strings 0.7 m long, and stays in it. The strings swing out to a largest angle of 35° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 1 kgL = 0.7 mθ = 35°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 2 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
A pitot-static tube in a water pipe reads a difference of 21 kPa between the stagnation pressure and the static pressure. Find the water velocity v at the tip.
p0 − p = 21 kPaρ = 1000 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 150 mm to 40 mm while rising 6 m. At section 1 the pressure is 250 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 450 °C and rejects heat to the surroundings at 40 °C. Its actual thermal efficiency is 23%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 450 °CTL = 40 °Cη = 23%
ηII = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is 5 °C outside, delivering 12 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 22 °CTL = 5 °CQ̇H = 12 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe closed at one end is 0.65 m long. The speed of sound is 343 m/s. Find the frequency f5 of its harmonic number 5.
v = 343 m/sn = 5L = 0.65 m
f5 = Hz
20.Waves, sound & opticsHard
Light of wavelength 589 nm falls on two slits 0.25 mm apart. The screen is 1.5 m away. Find the spacing Δy between neighbouring bright fringes.
λ = 589 nmd = 0.25 mmL = 1.5 m
Δy = mm
3Solutions
1.Kinematics
Answer: t = 4.444 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 72/3.6 = 20 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 20/4.5 = 4.444 s
Answer
t = 4.444 s
2.Kinematics
Answer: s = 187.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 1.5·5 = 7.5 m/s
Distance of each phase
s1 = ½·1.5·5² = 18.75 m
s2 = 7.5·21 = 157.5 m
s3 = 7.5²/(2·2.5) = 11.25 m
Total distance
s = 18.75 + 157.5 + 11.25 = 187.5 m
Answer
s = 187.5 m
3.Newton’s laws
Answer: a = 3.257 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 40·cos 20° = 37.59 m/s
t = x/vx = 73/37.59 = 1.942 s
Height at that time
y = 13.68·1.942 − ½·9.81·1.942² = 8.069 m
Answer
y = 8.069 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: t = 4.048 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 29·cos 15° = 28.01 m/s
vy = v0·sin θ = 29·sin 15° = 7.506 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 50 + 7.506·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (7.506 + √(56.34 + 981))/9.81 = 4.048 s
Answer
t = 4.048 s
7.Work & energy
Answer: P = 21.38 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 1200·9.81 = 11772 N
mg·sin θ = 11772·sin 8° = 1638 N
F = 1638 + 500 = 2138 N
Power
v = 36/3.6 = 10 m/s
P = F·v = 2138·10 = 21383 W = 21.38 kW
Answer
P = 21.38 kW
8.Work & energy
Answer: x = 44.64 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(2 − 0.25·1.5) = 79.71 J
Maximum compression
½kx² = 79.71 → x = √(2·79.71/800) = 0.4464 m = 44.64 cm
Answer
x = 44.64 cm
9.Momentum & collisions
Answer: ΔK/K = 54.29 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1600·17/3500 = 7.771 m/s
Kinetic energy before and after
Kbefore = ½·1600·17² = 231200 J
Kafter = ½·3500·7.771² = 105691 J
Fraction lost
ΔK/K = 125509/231200 = 54.29 %
Answer
ΔK/K = 54.29 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v = 132.9 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.7·(1 − cos 35°) = 0.1266 m
Speed after impact
V = √(2·9.81·0.1266) = 1.576 m/s
Collision
v = (m + M)·V/m = 1.012·1.576/0.012 = 132.9 m/s
Answer
v = 132.9 m/s
11.Hydrostatic force
Answer: F = 294.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2/2 = 5 m
A = H·b = 2·3 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5·6 = 294.3 kN
Answer
F = 294.3 kN
12.Hydrostatic force
Answer: ycp = 3.028 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·1.5 = 44.15 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·21000/1000) = 6.481 m/s
Answer
v = 6.481 m/s
14.Continuity & Bernoulli
Answer: p2 = 92.76 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 450 + 273.15 = 723.1 K
TL = 40 + 273.15 = 313.1 K
Carnot efficiency
ηCarnot = 1 − 313.1/723.1 = 56.7 %
Second-law efficiency
ηII = η/ηCarnot = 23/56.7 = 40.57 %
Answer
ηII = 40.57 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.6912 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 12/17.36 = 0.6912 kW
Answer
Ẇmin = 0.6912 kW
19.Waves, sound & optics
Answer: f5 = 659.6 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·0.65/5 = 0.52 m
Frequency
f = v/λ = 343/0.52 = 659.6 Hz
Answer
f5 = 659.6 Hz
20.Waves, sound & optics
Answer: Δy = 3.534 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …