Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 3 m/s² until it stops. Find the braking distance s.
v₀ = 100 km/ha = −3 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 19 m/s from the edge of a roof 40 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 19 m/sh₀ = 40 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 25 kg sled is pulled across level snow by a rope at 20° above the horizontal with a force of 200 N. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 25 kgF = 200 Nθ = 20°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 4.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 4.5 kgm2 = 1.5 kgμ = 0.2g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 14 m/sθ = 70°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 28 m/s and 35° above the horizontal from the top of a 60 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
v₀ = 28 m/sθ = 35°h = 60 mg = 9.81 m/s²
v = m/s
7.Work & energyMedium
A 1500 kg car drives up an 8° slope at a constant 36 km/h. Air resistance and rolling resistance together amount to 700 N. Find the power P the wheels must deliver, in kW.
A 10 kg block starts from rest at the bottom of a 15° slope and is pulled up the slope by a constant force of 45 N parallel to the slope. The coefficient of kinetic friction is 0.1. Find the speed v of the block after it has moved 2 m up the slope.
A 2.5 kg glider moving at 8 m/s makes a perfectly elastic head-on collision with a 4.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 2.5 kgm2 = 4.5 kgv1 = 8 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
At a crossing a 1400 kg car travelling east at 21 m/s collides with a 1500 kg car travelling north at 23 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1400 kgv1 = 21 m/s (E)m2 = 1500 kgv2 = 23 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 3 mH = 1 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of oil, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 75 mm. In the wide section the pressure is 320 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 250 mm, throat 125 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 110 mm. The discharge coefficient is 0.95. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A reversible refrigerator keeps a cold room at -10 °C by removing 9.5 kW of heat, and rejects heat to the surroundings at 30 °C. Find the rate Q̇H at which it rejects heat.
TL = -10 °CTH = 30 °CQ̇L = 9.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat engine takes in 2300 kJ of heat from a reservoir at 600 °C, produces 1242 kJ of work and rejects the rest to a reservoir at 15 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 600 °CTL = 15 °CQH = 2300 kJW = 1242 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
An object stands 40 cm in front of a thin converging lens with a focal length of 12 cm. Find the magnification m (negative for an inverted image).
do = 40 cmf = 12 cm
m =
20.Waves, sound & opticsHard
An object is 5 cm in front of a concave mirror with a radius of curvature of 16 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 5 cmR = 16 cm
di = cm
3Solutions
1.Kinematics
Answer: s = 128.6 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 27.78²/(2·3) = 128.6 m
Answer
s = 128.6 m
2.Kinematics
Answer: hmax = 58.4 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 19²/(2·9.81) = 18.4 m
Height above the ground
hmax = 40 + 18.4 = 58.4 m
Answer
hmax = 58.4 m
3.Newton’s laws
Answer: a = 6.103 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 245.3 − 200·sin 20° = 176.8 N
Horizontal forces
m·a = F·cos θ − μ·N = 187.9 − 35.37
a = 152.6/25 = 6.103 m/s²
Answer
a = 6.103 m/s²
4.Newton’s laws
Answer: T = 13.24 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 70° = 4.788 m/s
vy = v0·sin θ = 14·sin 70° = 13.16 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·13.16/9.81 = 2.682 s
Answer
t = 2.682 s
6.Projectile motion
Answer: v = 44.29 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 28·cos 35° = 22.94 m/s
vy0 = 28·sin 35° = 16.06 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(16.06² + 2·9.81·60) = 37.88 m/s
Impact speed
v = √(22.94² + 37.88²) = 44.29 m/s
Answer
v = 44.29 m/s
Check with energy: v² = v₀² + 2gh.
7.Work & energy
Answer: P = 27.48 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 1500·9.81 = 14715 N
mg·sin θ = 14715·sin 8° = 2048 N
F = 2048 + 700 = 2748 N
Power
v = 36/3.6 = 10 m/s
P = F·v = 2748·10 = 27479 W = 27.48 kW
Answer
P = 27.48 kW
8.Work & energy
Answer: v = 2.013 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 10·9.81 = 98.1 N
mg·sin θ = 25.39 N
μ·mg·cos θ = 9.476 N
Work–energy
½mv² = (45 − 34.87)·2 = 20.27 J
v = √(2·20.27/10) = 2.013 m/s
Answer
v = 2.013 m/s
9.Momentum & collisions
Answer: v′2 = 5.714 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2.5 − 4.5)/(2.5 + 4.5)·8 = −2.286 m/s
v′2 = 2·2.5/(2.5 + 4.5)·8 = 5.714 m/s
Answer
v′2 = 5.714 m/s
10.Momentum & collisions
Answer: v′ = 15.63 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1/2 = 3.5 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·2 = 68.67 kN
Answer
F = 68.67 kN
12.Hydrostatic force
Answer: F = 121.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2.5/2 = 3.75 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3.75·3.75 = 121.4 kN
Answer
F = 121.4 kN
13.Continuity & Bernoulli
Answer: p2 = 319.4 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.11 = 13597 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 343.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(100/250)·(343.1/293.1) = 4.682 L
Answer
V2 = 4.682 L
17.Heat engines & refrigerators
Answer: Q̇H = 10.94 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 30 + 273.15 = 303.1 K
TL = -10 + 273.15 = 263.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 9.5·303.1/263.1 = 10.94 kW
Answer
Q̇H = 10.94 kW
Power input: Ẇ = 1.444 kW.
18.Heat engines & refrigerators
Answer: Sgen = 1.038 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 2300 − 1242 = 1058 kJ
Absolute temperatures
TH = 600 + 273.15 = 873.1 K
TL = 15 + 273.15 = 288.1 K
Entropy changes of the reservoirs
ΔSH = −2300/873.1 = −2.634 kJ/K
ΔSL = 1058/288.1 = 3.672 kJ/K
Sgen = 3.672 − 2.634 = 1.038 kJ/K
Answer
Sgen = 1.038 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: m = −0.4286
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/12 − 1/40
di = 17.14 cm
Magnification
m = −di/do = −17.14/40 = −0.4286
Answer
m = −0.4286
20.Waves, sound & optics
Answer: di = −13.33 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.