Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 21 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 4 m/s². How long does it take the police car to catch up? Find t.
vcar = 21 m/sapolice = 4 m/s²v0,police = 0
t = s
2.KinematicsHard
A tram starts from rest and accelerates at 2.5 m/s² for 6 s, then runs at constant speed for 15 s, and finally brakes at 4.5 m/s² until it stops. Find the total distance s between the two stops.
a1 = 2.5 m/s²t1 = 6 st2 = 15 sa3 = −4.5 m/s²
s = m
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 10.5 m/s and comes to rest after 28 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 10.5 m/sd = 28 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 115 N pulls the front 9 kg block; the 12 kg block is towed behind. The coefficient of kinetic friction is 0.25 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 12 kgm2 = 9 kgF = 115 Nμ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 30° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 26 m/sθ = 30°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 25° above horizontal from the top of a 10 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 12 m/sθ = 25°h = 10 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A car travelling at 40 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.8. Find the stopping distance d.
v = 40 km/hμ = 0.8g = 9.81 m/s²
d = m
8.Work & energyHard
A 2.5 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.1) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 2.5 kgh = 5 mL = 3 mμ = 0.1k = 2000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 15 g bullet is fired horizontally into a 2.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 20 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 15 gM = 2.5 kgh = 20 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 1300 kg car runs into a parked 1600 kg car. The wrecks lock together and skid 7 m before stopping. The coefficient of kinetic friction between tyres and road is 0.7. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 50 mm. The water level is kept 3.5 m above the orifice and the discharge coefficient is 0.63. Find the flow rate Q. Use g = 9.81 m/s².
d = 50 mmh = 3.5 mCd = 0.63g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A closed water tank has compressed air above the water at a gauge pressure of 20 kPa. Water leaves through an opening with a diameter of 30 mm, 4.5 m below the water surface, into the open air. Ignoring losses, find the flow rate Q. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 550 °C and a cold reservoir at 15 °C. Find the highest possible thermal efficiency ηmax.
TH = 550 °CTL = 15 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump delivers 13 kW of heat to a heating system at 20 °C, taking heat from a source at -10 °C. Its actual COP is 30% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 20 °CTL = -10 °CηII = 30%Q̇H = 13 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A source of 1000 Hz moving at 15 m/s and an observer moving at 10 m/s approach each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 1000 Hzv = 343 m/svs = 15 m/svo = 10 m/s
f′ = Hz
20.Waves, sound & opticsHard
Light of wavelength 450 nm falls on two slits 0.15 mm apart. The screen is 1.5 m away. Find the distance y3 from the central bright fringe to bright fringe number 3.
λ = 450 nmd = 0.15 mmL = 1.5 mm = 3
y3 = mm
3Solutions
1.Kinematics
Answer: t = 10.5 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·21/4 = 10.5 s
Answer
t = 10.5 s
At that moment the police car moves at 2v = 42 m/s.
2.Kinematics
Answer: s = 295 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 2.5·6 = 15 m/s
Distance of each phase
s1 = ½·2.5·6² = 45 m
s2 = 15·15 = 225 m
s3 = 15²/(2·4.5) = 25 m
Total distance
s = 45 + 225 + 25 = 295 m
Answer
s = 295 m
3.Newton’s laws
Answer: μ = 0.2007
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 10.5²/(2·28) = 1.969 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 1.969/9.81 = 0.2007
Answer
μ = 0.2007
4.Newton’s laws
Answer: T = 65.71 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: t = 2.65 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 26·cos 30° = 22.52 m/s
vy = v0·sin θ = 26·sin 30° = 13 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·13/9.81 = 2.65 s
Answer
t = 2.65 s
6.Projectile motion
Answer: t = 2.036 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 12·cos 25° = 10.88 m/s
vy = v0·sin θ = 12·sin 25° = 5.071 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 10 + 5.071·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (5.071 + √(25.72 + 196.2))/9.81 = 2.036 s
Answer
t = 2.036 s
7.Work & energy
Answer: d = 7.865 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 40/3.6 = 11.11 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 11.11²/(2·0.8·9.81) = 7.865 m
Answer
d = 7.865 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 9.603 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 24.53·(5 − 0.1·3) = 115.3 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·4.7) = 9.603 m/s
Answer
v = 9.603 m/s
9.Momentum & collisions
Answer: v = 332.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.2) = 1.981 m/s
Collision
m·v = (m + M)·V → v = (0.015 + 2.5)·1.981/0.015 = 332.1 m/s
Answer
v = 332.1 m/s
10.Momentum & collisions
Answer: v1 = 21.87 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1/2 = 1 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1·1 = 9.81 kN
Answer
F = 9.81 kN
12.Hydrostatic force
Answer: F = 386.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.25·7.5 = 386.3 kN
Answer
F = 386.3 kN
13.Continuity & Bernoulli
Answer: Q = 10.25 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·3.5) = 8.287 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/823.1 = 64.99 %
Answer
ηmax = 64.99 %
18.Heat engines & refrigerators
Answer: Ẇ = 4.435 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 20 + 273.15 = 293.1 K
TL = -10 + 273.15 = 263.1 K
Carnot and actual COP
COPmax = 293.1/(293.1 − 263.1) = 9.772
COP = 0.3·9.772 = 2.931
Power input
Ẇ = Q̇H/COP = 13/2.931 = 4.435 kW
Answer
Ẇ = 4.435 kW
19.Waves, sound & optics
Answer: f′ = 1076 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …