Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 60 km/h sees an obstacle. Her reaction time is 0.5 s, after which the car brakes with a constant deceleration of 6.5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 60 km/htr = 0.5 sa = −6.5 m/s²
d = m
2.KinematicsHard
A ball is thrown straight up at 20 m/s from the edge of a roof 40 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 20 m/sh₀ = 40 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 20 kg box is pushed up a ramp at 20° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the pushing force F.
m = 20 kgθ = 20°μ = 0.2g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A 1.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 1.5 kgm2 = 1 kgμ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 50° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 20 m/sθ = 50°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 28 m/s and 20° above the horizontal from the top of a 35 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 28 m/sθ = 20°h = 35 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 1500 N/m. A 0.25 kg ball is placed on it and the spring is compressed by 8 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.25 kgk = 1500 N/mx = 8 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A spring of stiffness 1000 N/m at the bottom of a 40° slope is compressed by 12 cm against a 1 kg block and released. The coefficient of kinetic friction between block and slope is 0.2. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 4 kg glider moving at 6 m/s makes a perfectly elastic head-on collision with a 1.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 4 kgm2 = 1.5 kgv1 = 6 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.15 kg ball hits a wall at 14 m/s and bounces straight back at 10 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
m = 0.15 kgvin = 14 m/svout = 10 m/sΔt = 5 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 1 m below the surface. Find the depth ycp of the centre of pressure below the surface.
A pitot-static tube in a water pipe reads a difference of 21 kPa between the stagnation pressure and the static pressure. Find the water velocity v at the tip.
p0 − p = 21 kPaρ = 1000 kg/m³
v = m/s
14.Continuity & BernoulliHard
A closed water tank has compressed air above the water at a gauge pressure of 30 kPa. Water leaves through an opening with a diameter of 25 mm, 4 m below the water surface, into the open air. Ignoring losses, find the jet velocity v. Use g = 9.81 m/s².
A reversible (Carnot) heat engine takes in 2000 kJ of heat from a reservoir at 500 °C and rejects 720 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 500 °CQH = 2000 kJQL = 720 kJ
TL = °C
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1150 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 35 °C. Both engines produce the same work. Find Tm in °C.
TH = 1150 °CTL = 35 °C
Tm = °C
19.Waves, sound & opticsMedium
A source of 600 Hz moves at 30 m/s away from a stationary observer. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 600 Hzv = 343 m/svs = 30 m/s
f′ = Hz
20.Waves, sound & opticsHard
Two thin lenses share an axis, 10 cm apart: lens 1 with f₁ = 5 cm and lens 2 with f₂ = 12 cm. An object stands 40 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 5 cmf2 = 12 cms = 10 cmdo = 40 cm
di2 = cm
3Solutions
1.Kinematics
Answer: d = 29.7 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 60/3.6 = 16.67 m/s
Reaction distance
d1 = v₀·tr = 16.67·0.5 = 8.333 m
Braking distance
d2 = v₀²/(2a) = 16.67²/(2·6.5) = 21.37 m
Total
d = 8.333 + 21.37 = 29.7 m
Answer
d = 29.7 m
2.Kinematics
Answer: hmax = 60.39 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 20²/(2·9.81) = 20.39 m
Height above the ground
hmax = 40 + 20.39 = 60.39 m
Answer
hmax = 60.39 m
3.Newton’s laws
Answer: F = 104 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 67.1 + 36.87 = 104 N
Answer
F = 104 N
4.Newton’s laws
Answer: T = 5.886 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 20·cos 50° = 12.86 m/s
vy = v0·sin θ = 20·sin 50° = 15.32 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·15.32/9.81 = 3.124 s
Answer
t = 3.124 s
6.Projectile motion
Answer: H = 39.67 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 28·sin 20° = 9.577 m/s
Rise above the cliff
Δh = vy²/(2g) = 9.577²/(2·9.81) = 4.674 m
Height above the ground
H = 35 + 4.674 = 39.67 m
Answer
H = 39.67 m
7.Work & energy
Answer: h = 1.957 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 8 cm = 0.08 m
½kx² = ½·1500·0.08² = 4.8 J
Height
m·g = 0.25·9.81 = 2.453 N
h = ½kx²/(mg) = 4.8/2.453 = 1.957 m
Answer
h = 1.957 m
8.Work & energy
Answer: d = 0.922 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 12 cm = 0.12 m
½kx² = ½·1000·0.12² = 7.2 J
Energy balance along the slope
m·g = 1·9.81 = 9.81 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 7.2/(9.81·(0.6428 + 0.2·0.766)) = 0.922 m
Answer
d = 0.922 m
9.Momentum & collisions
Answer: v′2 = 8.727 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4 − 1.5)/(4 + 1.5)·6 = 2.727 m/s
v′2 = 2·4/(4 + 1.5)·6 = 8.727 m/s
Answer
v′2 = 8.727 m/s
10.Momentum & collisions
Answer: Favg = 720 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.15·(10 + 14) = 3.6 N·s
Average force
Favg = J/Δt = 3.6/0.005 = 720 N
Answer
Favg = 720 N
11.Hydrostatic force
Answer: F = 165.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1.5/2 = 3.75 m
A = H·b = 1.5·3 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.75·4.5 = 165.5 kN
Answer
F = 165.5 kN
12.Hydrostatic force
Answer: ycp = 2.8 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 3/2 = 2.5 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2.5·4.5 = 113.1 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·21000/1000) = 6.481 m/s
Answer
v = 6.481 m/s
14.Continuity & Bernoulli
Answer: v = 11.77 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli from the surface to the jet
v = √(2·(30000/1000 + 9.81·4)) = 11.77 m/s
Answer
v = 11.77 m/s
15.Ideal gas law
Answer: V = 348.2 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 370/16.04 = 23.07 mol
T = 90 + 273.15 = 363.1 K
Volume
V = nRT/P = 23.07·8.314·363.1/200 = 348.2 L
Answer
V = 348.2 L
16.Ideal gas law
Answer: V2 = 3.177 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 353.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(150/550)·(353.1/303.1) = 3.177 L
Answer
V2 = 3.177 L
17.Heat engines & refrigerators
Answer: TL = 5.184 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 500 + 273.15 = 773.1 K
Reversible heat ratio
TL = TH·QL/QH = 773.1·720/2000 = 278.3 K = 5.184 °C
Answer
TL = 5.184 °C
18.Heat engines & refrigerators
Answer: Tm = 592.5 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1150 + 273.15 = 1423 K
TL = 35 + 273.15 = 308.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (1423 + 308.1)/2 = 865.7 K = 592.5 °C
Answer
Tm = 592.5 °C
19.Waves, sound & optics
Answer: f′ = 551.7 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.