Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 2 m/s² along a runway. Find its speed v after 800 m.
v₀ = 0a = 2 m/s²s = 800 m
v = m/s
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 4.3 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 4.3 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 9 kg block slides down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 9 kgθ = 20°μ = 0.1g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3 kg block on a ramp at 35° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 5.5 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 3 kgm2 = 5.5 kgθ = 35°μ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 14 m/sθ = 70°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 15 m/s and 35° above the horizontal from the top of a 25 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the speed v with which it hits the ground.
v₀ = 15 m/sθ = 35°h = 25 mg = 9.81 m/s²
v = m/s
7.Work & energyMedium
A 1000 kg car drives up a 4° slope at a constant 54 km/h. Air resistance and rolling resistance together amount to 450 N. Find the power P the wheels must deliver, in kW.
A spring of stiffness 2000 N/m at the bottom of a 35° slope is compressed by 20 cm against a 1 kg block and released. The coefficient of kinetic friction between block and slope is 0.25. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 1600 kg car moving at 17 m/s runs into a stationary 1600 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 1600 kgv1 = 17 m/sm2 = 1600 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
A 0.45 kg ball hits a wall at 13 m/s and bounces straight back at 6 m/s. The contact lasts 40 ms. Find the average force Favg of the wall on the ball.
m = 0.45 kgvin = 13 m/svout = 6 m/sΔt = 40 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of oil, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 1 mb = 1 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 40 mm. In the wide section the pressure is 400 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A hose with an inner diameter of 20 mm siphons water from an open tank. The highest point C of the hose is 1 m above the water surface, and the outlet (open to the air) is 4 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the absolute pressure pC at point C. The atmospheric pressure is 101.3 kPa.
A heat engine works between a hot reservoir at 775 °C and a cold reservoir at 15 °C. Find the highest possible thermal efficiency ηmax.
TH = 775 °CTL = 15 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 20 kW of heat from a source at 500 °C and rejects heat to the surroundings at 30 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -15 °C and also rejects heat to the surroundings at 30 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 500 °CT0 = 30 °CTL = -15 °CQ̇H = 20 kW
Q̇L = kW
19.Waves, sound & opticsMedium
A source of 300 Hz moves at 25 m/s away from a stationary observer. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 300 Hzv = 343 m/svs = 25 m/s
f′ = Hz
20.Waves, sound & opticsHard
Light of wavelength 633 nm falls on two slits 0.15 mm apart. The screen is 1 m away. Find the distance y3 from the central bright fringe to bright fringe number 3.
λ = 633 nmd = 0.15 mmL = 1 mm = 3
y3 = mm
3Solutions
1.Kinematics
Answer: v = 56.57 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·2·800) = 56.57 m/s
Answer
v = 56.57 m/s
(203.6 km/h)
2.Kinematics
Answer: d = 81 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(4.3 − t₁)
4.905·t₁² + 343·t₁ − 1475 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1475))/(2·4.905) = 4.064 s
Depth
d = ½·9.81·4.064² = 81 m
Answer
d = 81 m
3.Newton’s laws
Answer: a = 2.433 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 53.96 N
m₁·g·sin θ = 16.88 N
μ·m₁·g·cos θ = 6.027 N
Acceleration of the system
a = (53.96 − 16.88 − 6.027)/8.5 = 3.653 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 5.5·(9.81 − 3.653) = 33.87 N
Answer
T = 33.87 N
5.Projectile motion
Answer: x = 12.84 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 70° = 4.788 m/s
vy = v0·sin θ = 14·sin 70° = 13.16 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·13.16/9.81 = 2.682 s
Horizontal distance
x = vx·t = 4.788·2.682 = 12.84 m
Answer
x = 12.84 m
6.Projectile motion
Answer: v = 26.75 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 15·cos 35° = 12.29 m/s
vy0 = 15·sin 35° = 8.604 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(8.604² + 2·9.81·25) = 23.76 m/s
Impact speed
v = √(12.29² + 23.76²) = 26.75 m/s
Answer
v = 26.75 m/s
Check with energy: v² = v₀² + 2gh.
7.Work & energy
Answer: P = 17.01 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 1000·9.81 = 9810 N
mg·sin θ = 9810·sin 4° = 684.3 N
F = 684.3 + 450 = 1134 N
Power
v = 54/3.6 = 15 m/s
P = F·v = 1134·15 = 17015 W = 17.01 kW
Answer
P = 17.01 kW
8.Work & energy
Answer: d = 5.239 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 20 cm = 0.2 m
½kx² = ½·2000·0.2² = 40 J
Energy balance along the slope
m·g = 1·9.81 = 9.81 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 40/(9.81·(0.5736 + 0.25·0.8192)) = 5.239 m
Answer
d = 5.239 m
9.Momentum & collisions
Answer: ΔK/K = 50 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1600·17/3200 = 8.5 m/s
Kinetic energy before and after
Kbefore = ½·1600·17² = 231200 J
Kafter = ½·3200·8.5² = 115600 J
Fraction lost
ΔK/K = 115600/231200 = 50 %
Answer
ΔK/K = 50 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: Favg = 213.8 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.45·(6 + 13) = 8.55 N·s
Average force
Favg = J/Δt = 8.55/0.04 = 213.8 N
Answer
Favg = 213.8 N
11.Hydrostatic force
Answer: F = 202.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·7.5 = 202.3 kN
Answer
F = 202.3 kN
12.Hydrostatic force
Answer: F = 12.95 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1/2 = 1.5 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·1.5·1 = 12.95 kN
Answer
F = 12.95 kN
13.Continuity & Bernoulli
Answer: p2 = 398.6 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
If this pressure falls to the vapour pressure of the water, the siphon stops working.
15.Ideal gas law
Answer: V = 108.7 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 310/16.04 = 19.33 mol
T = 65 + 273.15 = 338.1 K
Volume
V = nRT/P = 19.33·8.314·338.1/500 = 108.7 L
Answer
V = 108.7 L
16.Ideal gas law
Answer: V2 = 4.595 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 308.1 K, T2 = 453.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(250/400)·(453.1/308.1) = 4.595 L
Answer
V2 = 4.595 L
17.Heat engines & refrigerators
Answer: ηmax = 72.51 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 775 + 273.15 = 1048 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/1048 = 72.51 %
Answer
ηmax = 72.51 %
18.Heat engines & refrigerators
Answer: Q̇L = 69.75 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
T0 = 30 + 273.15 = 303.1 K
TL = -15 + 273.15 = 258.1 K
Engine work
η = 1 − 303.1/773.1 = 0.6079
Ẇ = 0.6079·20 = 12.16 kW
Heat removed by the refrigerator
COPR = 258.1/(303.1 − 258.1) = 5.737
Q̇L = 5.737·12.16 = 69.75 kW
Answer
Q̇L = 69.75 kW
19.Waves, sound & optics
Answer: f′ = 279.6 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …