Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 8 m/s² until it stops. Find the braking distance s.
v₀ = 108 km/ha = −8 m/s²v = 0
s = m
2.KinematicsHard
Ball A is dropped from rest from a height of 20 m. At the same instant ball B is thrown straight up from the ground directly below at 24 m/s. Ignore air resistance and use g = 9.81 m/s². At what height y above the ground do they meet?
H = 20 mv0B = 24 m/sg = 9.81 m/s²
y = m
3.Newton’s lawsMedium
An 8 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 8 kgθ = 40°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 5.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 5.5 kgm2 = 5 kgμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 30° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 26 m/sθ = 30°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is thrown from ground level at 32 m/s and 55° above the horizontal. It lands on the flat roof of a building 19 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 32 m/sθ = 55°hroof = 19 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 1000 N/m. A 0.1 kg ball is placed on it and the spring is compressed by 3 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.1 kgk = 1000 N/mx = 3 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A spring of stiffness 2000 N/m at the bottom of a 25° slope is compressed by 15 cm against a 1 kg block and released. The coefficient of kinetic friction between block and slope is 0.25. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 5 g bullet is fired horizontally into a 4.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 18 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 4.5 kgh = 18 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 20 g bullet is fired horizontally into a 3 kg block hanging from light strings 1.7 m long, and stays in it. The strings swing out to a largest angle of 20° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 20 gM = 3 kgL = 1.7 mθ = 20°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 2 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 2 m wide sits in the wall of a tank of oil, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 3 mH = 1 mb = 2 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 150 mm to 100 mm. In the wide section the pressure is 210 kPa and the velocity is 2.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A hose with an inner diameter of 32 mm siphons water from an open tank. The highest point C of the hose is 2.5 m above the water surface, and the outlet (open to the air) is 4.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the absolute pressure pC at point C. The atmospheric pressure is 101.3 kPa.
A reversible refrigerator keeps a cold room at -30 °C by removing 7 kW of heat, and rejects heat to the surroundings at 25 °C. Find the rate Q̇H at which it rejects heat.
TL = -30 °CTH = 25 °CQ̇L = 7 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 20 °C while it is 0 °C outside, delivering 8 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 20 °CTL = 0 °CQ̇H = 8 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe open at both ends must have its harmonic number 4 at 915 Hz. The speed of sound is 343 m/s. Find the length L of the pipe.
v = 343 m/sn = 4f4 = 915 Hz
L = m
20.Waves, sound & opticsHard
Light of wavelength 450 nm falls on two slits 0.25 mm apart. The screen is 2 m away. Find the distance y3 from the central bright fringe to bright fringe number 3.
λ = 450 nmd = 0.25 mmL = 2 mm = 3
y3 = mm
3Solutions
1.Kinematics
Answer: s = 56.25 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 30²/(2·8) = 56.25 m
Answer
s = 56.25 m
2.Kinematics
Answer: y = 16.59 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
20 − ½g·t² = 24·t − ½g·t² → t = 20/24 = 0.8333 s
Meeting height
y = 24·0.8333 − ½·9.81·0.8333² = 16.59 m
Answer
y = 16.59 m
3.Newton’s laws
Answer: a = 4.427 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 26·cos 30° = 22.52 m/s
vy = v0·sin θ = 26·sin 30° = 13 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 13²/(2·9.81) = 8.614 m
Answer
H = 8.614 m
6.Projectile motion
Answer: x = 82.22 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 18.35 m/s, vy = 26.21 m/s
Time to land on the roof
Larger root: the ball is descending.
19 = 26.21·t − 4.905·t²
t = (26.21 + √(26.21² − 2·9.81·19))/9.81 = 4.479 s
Horizontal distance
x = vx·t = 18.35·4.479 = 82.22 m
Answer
x = 82.22 m
7.Work & energy
Answer: h = 0.4587 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 3 cm = 0.03 m
½kx² = ½·1000·0.03² = 0.45 J
Height
m·g = 0.1·9.81 = 0.981 N
h = ½kx²/(mg) = 0.45/0.981 = 0.4587 m
Answer
h = 0.4587 m
8.Work & energy
Answer: d = 3.533 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 15 cm = 0.15 m
½kx² = ½·2000·0.15² = 22.5 J
Energy balance along the slope
m·g = 1·9.81 = 9.81 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 22.5/(9.81·(0.4226 + 0.25·0.9063)) = 3.533 m
Answer
d = 3.533 m
9.Momentum & collisions
Answer: v = 1693 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.18) = 1.879 m/s
Collision
m·v = (m + M)·V → v = (0.005 + 4.5)·1.879/0.005 = 1693 m/s
Answer
v = 1693 m/s
10.Momentum & collisions
Answer: v = 214.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.7·(1 − cos 20°) = 0.1025 m
Speed after impact
V = √(2·9.81·0.1025) = 1.418 m/s
Collision
v = (m + M)·V/m = 3.02·1.418/0.02 = 214.2 m/s
Answer
v = 214.2 m/s
11.Hydrostatic force
Answer: F = 39.24 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2/2 = 2 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·2 = 39.24 kN
Answer
F = 39.24 kN
12.Hydrostatic force
Answer: ycp = 3.524 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1/2 = 3.5 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3.5·2 = 60.43 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
If this pressure falls to the vapour pressure of the water, the siphon stops working.
15.Ideal gas law
Answer: P = 2300 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 170/44.01 = 3.863 mol
T = 85 + 273.15 = 358.1 K
Pressure
P = nRT/V = 3.863·8.314·358.1/0.005 = 2300 kPa
Answer
P = 2300 kPa
16.Ideal gas law
Answer: ρ = 7.638 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 130 + 273.15 = 403.1 K
Density
ρ = 800·32/(8.314·403.1) = 7.638 kg/m³
Answer
ρ = 7.638 kg/m³
17.Heat engines & refrigerators
Answer: Q̇H = 8.583 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 25 + 273.15 = 298.1 K
TL = -30 + 273.15 = 243.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 7·298.1/243.1 = 8.583 kW
Answer
Q̇H = 8.583 kW
Power input: Ẇ = 1.583 kW.
18.Heat engines & refrigerators
Answer: Ẇmin = 0.5458 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 8/14.66 = 0.5458 kW
Answer
Ẇmin = 0.5458 kW
19.Waves, sound & optics
Answer: L = 0.7497 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 343/915 = 0.3749 m
Length
L = nλ/2 = 4·0.3749/2 = 0.7497 m
Answer
L = 0.7497 m
20.Waves, sound & optics
Answer: y3 = 10.8 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …