Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 80 km/h sees an obstacle. Her reaction time is 1.4 s, after which the car brakes with a constant deceleration of 4 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 80 km/htr = 1.4 sa = −4 m/s²
d = m
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 32 m/s² for 2 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 32 m/s²t1 = 2 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
Masses of 2.5 kg and 2 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the acceleration a of the masses.
m1 = 2.5 kgm2 = 2 kgg = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 20° with a speed of 10.5 m/s. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 10.5 m/sθ = 20°μ = 0.3g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is kicked from level ground at 34 m/s and 60° above the horizontal towards a wall 41 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 34 m/sθ = 60°x = 41 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 20° above horizontal from the top of a 35 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 25 m/sθ = 20°h = 35 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 10 kg block slides 8 m down a slope at 35° to the horizontal, with a coefficient of kinetic friction of 0.1. Find the work Wf done against friction.
m = 10 kgθ = 35°μ = 0.1d = 8 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A spring of stiffness 800 N/m at the bottom of a 35° slope is compressed by 12 cm against a 0.5 kg block and released. The coefficient of kinetic friction between block and slope is 0.3. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 1400 kg car moving at 25 m/s runs into a stationary 2000 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1400 kgv1 = 25 m/sm2 = 2000 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.35 kg ball hits a wall at 25 m/s and bounces straight back at 17 m/s. The contact lasts 25 ms. Find the average force Favg of the wall on the ball.
m = 0.35 kgvin = 25 m/svout = 17 m/sΔt = 25 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 2 mH = 2 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water drains from a large open tank through a sharp-edged orifice with a diameter of 40 mm. The water level is kept 1 m above the orifice and the discharge coefficient is 0.62. Find the flow rate Q. Use g = 9.81 m/s².
d = 40 mmh = 1 mCd = 0.62g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A closed water tank has compressed air above the water at a gauge pressure of 120 kPa. Water leaves through an opening with a diameter of 20 mm, 2.5 m below the water surface, into the open air. Ignoring losses, find the jet velocity v. Use g = 9.81 m/s².
A heat engine receives heat from a source at 700 °C and rejects heat to the surroundings at 15 °C. Its actual thermal efficiency is 42%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 700 °CTL = 15 °Cη = 42%
ηII = %
18.Heat engines & refrigeratorsHard
A heat engine takes in 2700 kJ of heat from a reservoir at 800 °C, produces 1161 kJ of work and rejects the rest to a reservoir at 35 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 800 °CTL = 35 °CQH = 2700 kJW = 1161 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
A string fixed at both ends must have its fundamental (first harmonic) at 125 Hz; waves travel on it at 100 m/s. Find its length L.
v = 100 m/sn = 1f1 = 125 Hz
L = m
20.Waves, sound & opticsHard
Light of wavelength 500 nm falls at right angles on a grating with 600 lines per millimetre. Find the angle θ3 of the order-3 maximum.
N = 600 mm⁻¹λ = 500 nmm = 3
θ3 = °
3Solutions
1.Kinematics
Answer: d = 92.84 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 80/3.6 = 22.22 m/s
Reaction distance
d1 = v₀·tr = 22.22·1.4 = 31.11 m
Braking distance
d2 = v₀²/(2a) = 22.22²/(2·4) = 61.73 m
Total
d = 31.11 + 61.73 = 92.84 m
Answer
d = 92.84 m
2.Kinematics
Answer: hmax = 272.8 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 32·2 = 64 m/s
h₁ = ½·32·2² = 64 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 64²/(2·9.81) = 208.8 m
hmax = 64 + 208.8 = 272.8 m
Answer
hmax = 272.8 m
3.Newton’s laws
Answer: a = 1.09 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (2.5 − 2)·9.81/(2.5 + 2) = 1.09 m/s²
Answer
a = 1.09 m/s²
4.Newton’s laws
Answer: d = 9.006 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 20° + 0.3·cos 20°) = 6.121 m/s²
Distance
d = v₀²/(2a) = 10.5²/(2·6.121) = 9.006 m
Answer
d = 9.006 m
5.Projectile motion
Answer: y = 42.48 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 34·cos 60° = 17 m/s
t = x/vx = 41/17 = 2.412 s
Height at that time
y = 29.44·2.412 − ½·9.81·2.412² = 42.48 m
Answer
y = 42.48 m
The ball is still rising at the wall.
6.Projectile motion
Answer: x = 86.49 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 25·cos 20° = 23.49 m/s
vy = v0·sin θ = 25·sin 20° = 8.551 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 35 + 8.551·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (8.551 + √(73.11 + 686.7))/9.81 = 3.681 s
Horizontal distance
x = vx·t = 23.49·3.681 = 86.49 m
Answer
x = 86.49 m
7.Work & energy
Answer: Wf = 64.29 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 98.1·0.8192 = 80.36 N
F = μN = 0.1·80.36 = 8.036 N
Work against friction
Wf = F·d = 8.036·8 = 64.29 J
Answer
Wf = 64.29 J
8.Work & energy
Answer: d = 1.433 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 12 cm = 0.12 m
½kx² = ½·800·0.12² = 5.76 J
Energy balance along the slope
m·g = 0.5·9.81 = 4.905 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 5.76/(4.905·(0.5736 + 0.3·0.8192)) = 1.433 m
Answer
d = 1.433 m
9.Momentum & collisions
Answer: ΔK = 257353 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1400·25/3400 = 10.29 m/s
Kinetic energy before and after
Kbefore = ½·1400·25² = 437500 J
Kafter = ½·3400·10.29² = 180147 J
Energy lost
ΔK = 437500 − 180147 = 257353 J
Answer
ΔK = 257353 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: Favg = 588 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.35·(17 + 25) = 14.7 N·s
Average force
Favg = J/Δt = 14.7/0.025 = 588 N
Answer
Favg = 588 N
11.Hydrostatic force
Answer: F = 206 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·6 = 206 kN
Answer
F = 206 kN
12.Hydrostatic force
Answer: ycp = 3.111 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·2 = 58.86 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 1·2³/12 = 0.6667 m⁴
ycp = yc + Ic/(yc·A) = 3 + 0.6667/(3·2) = 3.111 m
Answer
ycp = 3.111 m
13.Continuity & Bernoulli
Answer: Q = 3.451 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·1) = 4.429 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli from the surface to the jet
v = √(2·(120000/1000 + 9.81·2.5)) = 17 m/s
Answer
v = 17 m/s
15.Ideal gas law
Answer: V = 40.67 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 420/32 = 13.13 mol
T = 25 + 273.15 = 298.1 K
Volume
V = nRT/P = 13.13·8.314·298.1/800 = 40.67 L
Answer
V = 40.67 L
16.Ideal gas law
Answer: ρ = 0.7781 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 160 + 273.15 = 433.1 K
Density
ρ = 700·4.003/(8.314·433.1) = 0.7781 kg/m³
Answer
ρ = 0.7781 kg/m³
17.Heat engines & refrigerators
Answer: ηII = 59.67 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 700 + 273.15 = 973.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηCarnot = 1 − 288.1/973.1 = 70.39 %
Second-law efficiency
ηII = η/ηCarnot = 42/70.39 = 59.67 %
Answer
ηII = 59.67 %
18.Heat engines & refrigerators
Answer: Sgen = 2.478 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 2700 − 1161 = 1539 kJ
Absolute temperatures
TH = 800 + 273.15 = 1073 K
TL = 35 + 273.15 = 308.1 K
Entropy changes of the reservoirs
ΔSH = −2700/1073 = −2.516 kJ/K
ΔSL = 1539/308.1 = 4.994 kJ/K
Sgen = 4.994 − 2.516 = 2.478 kJ/K
Answer
Sgen = 2.478 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: L = 0.4 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 100/125 = 0.8 m
Length
L = nλ/2 = 1·0.8/2 = 0.4 m
Answer
L = 0.4 m
20.Waves, sound & optics
Answer: θ3 = 64.16 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …