Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 36 km/h brakes with a constant deceleration of 8 m/s² until it stops. How long does braking take? Find t.
v₀ = 36 km/ha = −8 m/s²v = 0
t = s
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 5 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 5 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
An 8 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 8 kgθ = 35°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
An 8 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 8 kgm2 = 4 kgμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is kicked from level ground at 20 m/s and 40° above the horizontal towards a wall 12 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 20 m/sθ = 40°x = 12 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 35° above horizontal from the top of a 15 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 35 m/sθ = 35°h = 15 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 0.5 kg ball hangs on a light string of length 0.8 m. It is pulled aside until the string makes 90° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 0.5 kgL = 0.8 mθ = 90°g = 9.81 m/s²
T = N
8.Work & energyHard
A spring of stiffness 800 N/m at the bottom of a 15° slope is compressed by 20 cm against a 5 kg block and released. The coefficient of kinetic friction between block and slope is 0.1. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 2.5 kg glider moving at 9 m/s makes a perfectly elastic head-on collision with a 1.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 2.5 kgm2 = 1.5 kgv1 = 9 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 20 g bullet is fired horizontally into a 5 kg block hanging from light strings 0.5 m long, and stays in it. The strings swing out to a largest angle of 15° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 20 gM = 5 kgL = 0.5 mθ = 15°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows at 10 L/s through a horizontal pipe that narrows from 150 mm to 100 mm. The pressure in the narrow section is 80 kPa. Ignoring losses, find the pressure p1 in the wide section.
A hose with an inner diameter of 20 mm siphons water from an open tank. The highest point C of the hose is 2 m above the water surface, and the outlet (open to the air) is 1 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 20 mmzC = +2 mz2 = −1 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
What volume V does 50 g of CO₂ occupy at 650 kPa and 75 °C? Treat it as an ideal gas.
A heat engine works between a hot reservoir at 550 °C and a cold reservoir at 20 °C. It takes in 1900 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 550 °CTL = 20 °CQH = 1900 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump delivers 11.5 kW of heat to a heating system at 45 °C, taking heat from a source at 7 °C. Its actual COP is 35% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 45 °CTL = 7 °CηII = 35%Q̇H = 11.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
Light inside a transparent block is totally reflected at the boundary with air (n = 1.00) for every angle of incidence above 24.4°. Find the refractive index n1 of the block.
θc = 24.4°n2 = 1.00
n1 =
20.Waves, sound & opticsHard
Light of wavelength 550 nm passes through a single slit 0.05 mm wide. Find the angle θ1 of dark fringe number 1 from the straight-through direction.
λ = 550 nma = 0.05 mmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: t = 1.25 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 36/3.6 = 10 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 10/8 = 1.25 s
Answer
t = 1.25 s
2.Kinematics
Answer: d = 107.7 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(5 − t₁)
4.905·t₁² + 343·t₁ − 1715 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1715))/(2·4.905) = 4.686 s
Depth
d = ½·9.81·4.686² = 107.7 m
Answer
d = 107.7 m
3.Newton’s laws
Answer: a = 4.02 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 20·cos 40° = 15.32 m/s
t = x/vx = 12/15.32 = 0.7832 s
Height at that time
y = 12.86·0.7832 − ½·9.81·0.7832² = 7.06 m
Answer
y = 7.06 m
The ball is still rising at the wall.
6.Projectile motion
Answer: t = 4.738 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 35·cos 35° = 28.67 m/s
vy = v0·sin θ = 35·sin 35° = 20.08 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 15 + 20.08·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (20.08 + √(403 + 294.3))/9.81 = 4.738 s
Answer
t = 4.738 s
7.Work & energy
Answer: T = 14.71 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·0.8·(1 − cos 90°) = 15.7 m²/s²
Forces at the bottom
m·g = 0.5·9.81 = 4.905 N
T = mg + mv²/L = 4.905 + 0.5·15.7/0.8 = 14.71 N
Answer
T = 14.71 N
Check: T = mg(3 − 2cos θ) = 14.71 N.
8.Work & energy
Answer: d = 0.9178 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 20 cm = 0.2 m
½kx² = ½·800·0.2² = 16 J
Energy balance along the slope
m·g = 5·9.81 = 49.05 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 16/(49.05·(0.2588 + 0.1·0.9659)) = 0.9178 m
Answer
d = 0.9178 m
9.Momentum & collisions
Answer: v′2 = 11.25 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2.5 − 1.5)/(2.5 + 1.5)·9 = 2.25 m/s
v′2 = 2·2.5/(2.5 + 1.5)·9 = 11.25 m/s
Answer
v′2 = 11.25 m/s
10.Momentum & collisions
Answer: v = 145.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.5·(1 − cos 15°) = 0.01704 m
Speed after impact
V = √(2·9.81·0.01704) = 0.5782 m/s
Collision
v = (m + M)·V/m = 5.02·0.5782/0.02 = 145.1 m/s
Answer
v = 145.1 m/s
11.Hydrostatic force
Answer: F = 101.2 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·3.75 = 101.2 kN
Answer
F = 101.2 kN
12.Hydrostatic force
Answer: F = 58.86 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2/2 = 1.5 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.5·4 = 58.86 kN
Answer
F = 58.86 kN
13.Continuity & Bernoulli
Answer: p1 = 80.65 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(400/400)·(443.1/288.1) = 7.69 L
Answer
V2 = 7.69 L
17.Heat engines & refrigerators
Answer: Wmax = 1223 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
TL = 20 + 273.15 = 293.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 293.1/823.1 = 64.39 %
Maximum work
Wmax = ηmax·QH = 0.6439·1900 = 1223 kJ
Answer
Wmax = 1223 kJ
18.Heat engines & refrigerators
Answer: Ẇ = 3.924 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 45 + 273.15 = 318.1 K
TL = 7 + 273.15 = 280.1 K
Carnot and actual COP
COPmax = 318.1/(318.1 − 280.1) = 8.372
COP = 0.35·8.372 = 2.93
Power input
Ẇ = Q̇H/COP = 11.5/2.93 = 3.924 kW
Answer
Ẇ = 3.924 kW
19.Waves, sound & optics
Answer: n1 = 2.421
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refractive index of the block
n₁ = n₂/sin θc = 1.00/0.4131 = 2.421
Answer
n1 = 2.421
20.Waves, sound & optics
Answer: θ1 = 0.6303 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …