Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 60 km/h sees an obstacle. Her reaction time is 1.1 s, after which the car brakes with a constant deceleration of 7.5 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 60 km/htr = 1.1 sa = −7.5 m/s²
d = m
2.KinematicsHard
Ball A is dropped from rest from a height of 10 m. At the same instant ball B is thrown straight up from the ground directly below at 11 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 10 mv0B = 11 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 12 kg block slides down a frictionless slope at 25° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 12 kgθ = 25°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 80 N pulls the front 3 kg block; the 7 kg block is towed behind. The coefficient of kinetic friction is 0.1 for both blocks. Use g = 9.81 m/s². Find the acceleration a of the blocks.
m1 = 7 kgm2 = 3 kgF = 80 Nμ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 30 m/s and must land 30 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 30 m/sR = 30 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 60° above horizontal from the top of a 30 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 24 m/sθ = 60°h = 30 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 2000 N/m. A 0.25 kg ball is placed on it and the spring is compressed by 6 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.25 kgk = 2000 N/mx = 6 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A spring of stiffness 3000 N/m at the bottom of a 15° slope is compressed by 15 cm against a 5 kg block and released. The coefficient of kinetic friction between block and slope is 0.2. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 0.5 kg glider moving at 10 m/s makes a perfectly elastic head-on collision with a 2 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 0.5 kgm2 = 2 kgv1 = 10 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 1400 kg car runs into a parked 1800 kg car. The wrecks lock together and skid 19 m before stopping. The coefficient of kinetic friction between tyres and road is 0.8. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 150 mm to 100 mm. In the wide section the pressure is 280 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 1 m. At section 1 the pressure is 230 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at 4 °C by removing 4 kW of heat, and rejects heat to the surroundings at 28 °C. Find the rate Q̇H at which it rejects heat.
TL = 4 °CTH = 28 °CQ̇L = 4 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 190 kW of heat from a source at 700 °C and rejects heat to the surroundings at 30 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -25 °C and also rejects heat to the surroundings at 30 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 700 °CT0 = 30 °CTL = -25 °CQ̇H = 190 kW
Q̇L = kW
19.Waves, sound & opticsMedium
Light inside a transparent block is totally reflected at the boundary with acrylic (n = 1.49) for every angle of incidence above 30°. Find the refractive index n1 of the block.
θc = 30°n2 = 1.49
n1 =
20.Waves, sound & opticsHard
Two thin lenses share an axis, 20 cm apart: lens 1 with f₁ = 8 cm and lens 2 with f₂ = −15 cm. An object stands 20 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 8 cmf2 = −15 cms = 20 cmdo = 20 cm
di2 = cm
3Solutions
1.Kinematics
Answer: d = 36.85 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 60/3.6 = 16.67 m/s
Reaction distance
d1 = v₀·tr = 16.67·1.1 = 18.33 m
Braking distance
d2 = v₀²/(2a) = 16.67²/(2·7.5) = 18.52 m
Total
d = 18.33 + 18.52 = 36.85 m
Answer
d = 36.85 m
2.Kinematics
Answer: t = 0.9091 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
10 − ½g·t² = 11·t − ½g·t² → t = 10/11 = 0.9091 s
Answer
t = 0.9091 s
3.Newton’s laws
Answer: a = 4.146 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·30/30² = 0.327
Angle
2θ = 19.09° → θ = 9.543°
Answer
θ = 9.543°
The other solution is 90° − θ = 80.46°.
6.Projectile motion
Answer: t = 5.375 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 60° = 12 m/s
vy = v0·sin θ = 24·sin 60° = 20.78 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 30 + 20.78·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (20.78 + √(432 + 588.6))/9.81 = 5.375 s
Answer
t = 5.375 s
7.Work & energy
Answer: h = 1.468 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 6 cm = 0.06 m
½kx² = ½·2000·0.06² = 3.6 J
Height
m·g = 0.25·9.81 = 2.453 N
h = ½kx²/(mg) = 3.6/2.453 = 1.468 m
Answer
h = 1.468 m
8.Work & energy
Answer: d = 1.522 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 15 cm = 0.15 m
½kx² = ½·3000·0.15² = 33.75 J
Energy balance along the slope
m·g = 5·9.81 = 49.05 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 33.75/(49.05·(0.2588 + 0.2·0.9659)) = 1.522 m
Answer
d = 1.522 m
9.Momentum & collisions
Answer: v′2 = 4 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (0.5 − 2)/(0.5 + 2)·10 = −6 m/s
v′2 = 2·0.5/(0.5 + 2)·10 = 4 m/s
Answer
v′2 = 4 m/s
10.Momentum & collisions
Answer: v1 = 39.47 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.75·1.5 = 40.47 kN
Answer
F = 40.47 kN
12.Hydrostatic force
Answer: F = 148.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2/2 = 4 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·4·3 = 148.3 kN
Answer
F = 148.3 kN
13.Continuity & Bernoulli
Answer: p2 = 273.8 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 413.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(100/700)·(413.1/293.1) = 2.013 L
Answer
V2 = 2.013 L
17.Heat engines & refrigerators
Answer: Q̇H = 4.346 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 28 + 273.15 = 301.1 K
TL = 4 + 273.15 = 277.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 4·301.1/277.1 = 4.346 kW
Answer
Q̇H = 4.346 kW
Power input: Ẇ = 0.3464 kW.
18.Heat engines & refrigerators
Answer: Q̇L = 590.2 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 700 + 273.15 = 973.1 K
T0 = 30 + 273.15 = 303.1 K
TL = -25 + 273.15 = 248.1 K
Engine work
η = 1 − 303.1/973.1 = 0.6885
Ẇ = 0.6885·190 = 130.8 kW
Heat removed by the refrigerator
COPR = 248.1/(303.1 − 248.1) = 4.512
Q̇L = 4.512·130.8 = 590.2 kW
Answer
Q̇L = 590.2 kW
19.Waves, sound & optics
Answer: n1 = 2.98
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refractive index of the block
n₁ = n₂/sin θc = 1.49/0.5 = 2.98
Answer
n1 = 2.98
20.Waves, sound & optics
Answer: di2 = −4.615 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.