Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 45 km/h brakes with a constant deceleration of 3.5 m/s² until it stops. Find the braking distance s.
v₀ = 45 km/ha = −3.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 11 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 11 m/sh₀ = 10 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 8.5 m/s and comes to rest after 74 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 8.5 m/sd = 74 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 5 kgm2 = 3 kgμ = 0.3g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 65° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 14 m/sθ = 65°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 5 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 18 m/sθ = 45°h = 5 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 1 kg block slides 16 m down a slope at 25° to the horizontal, with a coefficient of kinetic friction of 0.35. Find the work Wf done against friction.
m = 1 kgθ = 25°μ = 0.35d = 16 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 10 kg block starts from rest at the bottom of a 35° slope and is pulled up the slope by a constant force of 125 N parallel to the slope. The coefficient of kinetic friction is 0.25. Find the speed v of the block after it has moved 10 m up the slope.
A 3.5 kg glider moving at 9 m/s makes a perfectly elastic head-on collision with a 1.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3.5 kgm2 = 1.5 kgv1 = 9 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
An 8 g bullet is fired horizontally into a 5 kg block hanging from light strings 0.7 m long, and stays in it. The strings swing out to a largest angle of 30° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 8 gM = 5 kgL = 0.7 mθ = 30°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 120 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 100 mm, throat 50 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 180 mm. The discharge coefficient is 0.97. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A reversible refrigerator keeps a cold room at -20 °C by removing 9 kW of heat, and rejects heat to the surroundings at 30 °C. Find the rate Q̇H at which it rejects heat.
TL = -20 °CTH = 30 °CQ̇L = 9 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat pump delivers 18.5 kW of heat to a heating system at 55 °C, taking heat from a source at 0 °C. Its actual COP is 45% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 55 °CTL = 0 °CηII = 45%Q̇H = 18.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
An observer moves at 15 m/s away from a stationary source of 440 Hz. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 440 Hzv = 343 m/svo = 15 m/s
f′ = Hz
20.Waves, sound & opticsHard
A parking sensor at rest sends ultrasound of 20 kHz towards a car that approaches at 5 m/s. Find the frequency f″ of the echo received back at the sensor (speed of sound 343 m/s).
f = 20 kHzu = 5 m/sv = 343 m/s
f″ = Hz
3Solutions
1.Kinematics
Answer: s = 22.32 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 45/3.6 = 12.5 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 12.5²/(2·3.5) = 22.32 m
Answer
s = 22.32 m
2.Kinematics
Answer: hmax = 16.17 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 11²/(2·9.81) = 6.167 m
Height above the ground
hmax = 10 + 6.167 = 16.17 m
Answer
hmax = 16.17 m
3.Newton’s laws
Answer: μ = 0.04976
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 8.5²/(2·74) = 0.4882 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 0.4882/9.81 = 0.04976
Answer
μ = 0.04976
4.Newton’s laws
Answer: a = 1.839 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 65° = 5.917 m/s
vy = v0·sin θ = 14·sin 65° = 12.69 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·12.69/9.81 = 2.587 s
Horizontal distance
x = vx·t = 5.917·2.587 = 15.31 m
Answer
x = 15.31 m
6.Projectile motion
Answer: x = 37.44 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 18·cos 45° = 12.73 m/s
vy = v0·sin θ = 18·sin 45° = 12.73 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 5 + 12.73·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (12.73 + √(162 + 98.1))/9.81 = 2.941 s
Horizontal distance
x = vx·t = 12.73·2.941 = 37.44 m
Answer
x = 37.44 m
7.Work & energy
Answer: Wf = 49.79 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 9.81·0.9063 = 8.891 N
F = μN = 0.35·8.891 = 3.112 N
Work against friction
Wf = F·d = 3.112·16 = 49.79 J
Answer
Wf = 49.79 J
8.Work & energy
Answer: v = 9.863 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 10·9.81 = 98.1 N
mg·sin θ = 56.27 N
μ·mg·cos θ = 20.09 N
Work–energy
½mv² = (125 − 76.36)·10 = 486.4 J
v = √(2·486.4/10) = 9.863 m/s
Answer
v = 9.863 m/s
9.Momentum & collisions
Answer: v′2 = 12.6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3.5 − 1.5)/(3.5 + 1.5)·9 = 3.6 m/s
v′2 = 2·3.5/(3.5 + 1.5)·9 = 12.6 m/s
Answer
v′2 = 12.6 m/s
10.Momentum & collisions
Answer: v = 849.1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.7·(1 − cos 30°) = 0.09378 m
Speed after impact
V = √(2·9.81·0.09378) = 1.356 m/s
Collision
v = (m + M)·V/m = 5.008·1.356/0.008 = 849.1 m/s
Answer
v = 849.1 m/s
11.Hydrostatic force
Answer: F = 176.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 3/2 = 4 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4·4.5 = 176.6 kN
Answer
F = 176.6 kN
12.Hydrostatic force
Answer: F = 250.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 3/2 = 4.5 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·4.5·4.5 = 250.3 kN
Answer
F = 250.3 kN
13.Continuity & Bernoulli
Answer: p2 = 118.9 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.18 = 22249 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 298.1 K, T2 = 363.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(200/750)·(363.1/298.1) = 0.6496 L
Answer
V2 = 0.6496 L
17.Heat engines & refrigerators
Answer: Q̇H = 10.78 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 30 + 273.15 = 303.1 K
TL = -20 + 273.15 = 253.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 9·303.1/253.1 = 10.78 kW
Answer
Q̇H = 10.78 kW
Power input: Ẇ = 1.778 kW.
18.Heat engines & refrigerators
Answer: Ẇ = 6.89 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 55 + 273.15 = 328.1 K
TL = 0 + 273.15 = 273.1 K
Carnot and actual COP
COPmax = 328.1/(328.1 − 273.1) = 5.966
COP = 0.45·5.966 = 2.685
Power input
Ẇ = Q̇H/COP = 18.5/2.685 = 6.89 kW
Answer
Ẇ = 6.89 kW
19.Waves, sound & optics
Answer: f′ = 420.8 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.