Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 80 km/h brakes with a constant deceleration of 6 m/s² until it stops. How long does braking take? Find t.
v₀ = 80 km/ha = −6 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 16 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 16 m/sh₀ = 25 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
An 18 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 18 kgθ = 25°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 7 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2.5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 7 kgm2 = 2.5 kgμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 28 m/sθ = 20°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 55° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 21 m/sθ = 55°h = 45 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A car travelling at 30 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.4. Find the stopping distance d.
v = 30 km/hμ = 0.4g = 9.81 m/s²
d = m
8.Work & energyHard
A 0.5 kg block is released from rest at height 2 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4.5 m long (μ = 0.1) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 0.5 kgh = 2 mL = 4.5 mμ = 0.1k = 500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 900 kg car moving at 9 m/s runs into a stationary 1800 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 900 kgv1 = 9 m/sm2 = 1800 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 5 g bullet is fired horizontally into a 2.5 kg block hanging from light strings 1.5 m long, and stays in it. The strings swing out to a largest angle of 20° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 2.5 kgL = 1.5 mθ = 20°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 1 mH = 2 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 120 kPa and the velocity is 1.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 150 mm to 50 mm while rising 10 m. At section 1 the pressure is 350 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 200 °C and a cold reservoir at 30 °C. Find the highest possible thermal efficiency ηmax.
TH = 200 °CTL = 30 °C
ηmax = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1050 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 30 °C. Both engines have the same thermal efficiency. Find Tm in °C.
TH = 1050 °CTL = 30 °C
Tm = °C
19.Waves, sound & opticsMedium
A string fixed at both ends must have its harmonic number 5 at 300 Hz; waves travel on it at 180 m/s. Find its length L.
v = 180 m/sn = 5f5 = 300 Hz
L = m
20.Waves, sound & opticsHard
Light of wavelength 656 nm falls at right angles on a grating with 600 lines per millimetre. Find the angle θ2 of the order-2 maximum.
N = 600 mm⁻¹λ = 656 nmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: t = 3.704 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 80/3.6 = 22.22 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 22.22/6 = 3.704 s
Answer
t = 3.704 s
2.Kinematics
Answer: t = 4.416 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−25 = 16·t − ½·9.81·t²
4.905·t² − 16·t − 25 = 0
Solve the quadratic
Only the positive root is physical.
t = (16 + √(16² + 2·9.81·25))/9.81 = 4.416 s
Answer
t = 4.416 s
3.Newton’s laws
Answer: a = 2.812 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 20° = 26.31 m/s
vy = v0·sin θ = 28·sin 20° = 9.577 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·9.577/9.81 = 1.952 s
Answer
t = 1.952 s
6.Projectile motion
Answer: t = 5.253 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 21·cos 55° = 12.05 m/s
vy = v0·sin θ = 21·sin 55° = 17.2 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 45 + 17.2·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (17.2 + √(295.9 + 882.9))/9.81 = 5.253 s
Answer
t = 5.253 s
7.Work & energy
Answer: d = 8.849 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 30/3.6 = 8.333 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 8.333²/(2·0.4·9.81) = 8.849 m
Answer
d = 8.849 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: x = 17.44 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(2 − 0.1·4.5) = 7.603 J
Maximum compression
½kx² = 7.603 → x = √(2·7.603/500) = 0.1744 m = 17.44 cm
Answer
x = 17.44 cm
9.Momentum & collisions
Answer: ΔK = 24300 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 900·9/2700 = 3 m/s
Kinetic energy before and after
Kbefore = ½·900·9² = 36450 J
Kafter = ½·2700·3² = 12150 J
Energy lost
ΔK = 36450 − 12150 = 24300 J
Answer
ΔK = 24300 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v = 667.4 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.5·(1 − cos 20°) = 0.09046 m
Speed after impact
V = √(2·9.81·0.09046) = 1.332 m/s
Collision
v = (m + M)·V/m = 2.505·1.332/0.005 = 667.4 m/s
Answer
v = 667.4 m/s
11.Hydrostatic force
Answer: F = 137.3 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2/2 = 3.5 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·4 = 137.3 kN
Answer
F = 137.3 kN
12.Hydrostatic force
Answer: ycp = 2.167 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2/2 = 2 m
A = H·b = 2·1 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·2 = 39.24 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 1·2³/12 = 0.6667 m⁴
ycp = yc + Ic/(yc·A) = 2 + 0.6667/(2·2) = 2.167 m
Answer
ycp = 2.167 m
13.Continuity & Bernoulli
Answer: p2 = 115.4 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 313.1 K, T2 = 453.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(350/450)·(453.1/313.1) = 11.25 L
Answer
V2 = 11.25 L
17.Heat engines & refrigerators
Answer: ηmax = 35.93 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 200 + 273.15 = 473.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/473.1 = 35.93 %
Answer
ηmax = 35.93 %
18.Heat engines & refrigerators
Answer: Tm = 360.2 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1050 + 273.15 = 1323 K
TL = 30 + 273.15 = 303.1 K
Equal efficiencies
1 − Tm/TH = 1 − TL/Tm gives Tm² = TH·TL.
Tm = √(1323·303.1) = 633.3 K = 360.2 °C
Answer
Tm = 360.2 °C
19.Waves, sound & optics
Answer: L = 1.5 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 180/300 = 0.6 m
Length
L = nλ/2 = 5·0.6/2 = 1.5 m
Answer
L = 1.5 m
20.Waves, sound & optics
Answer: θ2 = 51.92 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …