Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 240 km/h to take off and the usable runway is 1000 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 240 km/hs = 1000 m
a = m/s²
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 3.9 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 3.9 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 6 kg block slides down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 6 kgθ = 20°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 90 N pulls the front 1 kg block; the 3 kg block is towed behind. The coefficient of kinetic friction is 0.1 for both blocks. Use g = 9.81 m/s². Find the acceleration a of the blocks.
m1 = 3 kgm2 = 1 kgF = 90 Nμ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 36 m/sθ = 20°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is thrown from ground level at 39 m/s and 50° above the horizontal. It lands on the flat roof of a building 2 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 39 m/sθ = 50°hroof = 2 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 2000 kg car drives up a 2° slope at a constant 72 km/h. Air resistance and rolling resistance together amount to 550 N. Find the power P the wheels must deliver, in kW.
A 1 kg block is released from rest at height 4 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.2) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 1 kgh = 4 mL = 2 mμ = 0.2k = 500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 20 g bullet is fired horizontally into a 1.5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 12 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 20 gM = 1.5 kgh = 12 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 1400 kg car runs into a parked 1400 kg car. The wrecks lock together and skid 19.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.6. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of seawater, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 150 mm to 100 mm. In the wide section the pressure is 130 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 1 m. At section 1 the pressure is 110 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 650 °C and a cold reservoir at 40 °C. Find the highest possible thermal efficiency ηmax.
TH = 650 °CTL = 40 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 90 kW of heat from a source at 900 °C and rejects heat to the surroundings at 27 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -20 °C and also rejects heat to the surroundings at 27 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 900 °CT0 = 27 °CTL = -20 °CQ̇H = 90 kW
Q̇L = kW
19.Waves, sound & opticsMedium
An object stands 60 cm in front of a thin converging lens with a focal length of 15 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 60 cmf = 15 cm
di = cm
20.Waves, sound & opticsHard
Two thin lenses share an axis, 30 cm apart: lens 1 with f₁ = 10 cm and lens 2 with f₂ = 5 cm. An object stands 30 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 10 cmf2 = 5 cms = 30 cmdo = 30 cm
di2 = cm
3Solutions
1.Kinematics
Answer: a = 2.222 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 240/3.6 = 66.67 m/s
Acceleration
a = v²/(2s) = 66.67²/(2·1000) = 2.222 m/s²
Answer
a = 2.222 m/s²
2.Kinematics
Answer: d = 67.29 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(3.9 − t₁)
4.905·t₁² + 343·t₁ − 1338 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1338))/(2·4.905) = 3.704 s
Depth
d = ½·9.81·3.704² = 67.29 m
Answer
d = 67.29 m
3.Newton’s laws
Answer: a = 1.512 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 36·cos 20° = 33.83 m/s
vy = v0·sin θ = 36·sin 20° = 12.31 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·12.31/9.81 = 2.51 s
Horizontal distance
x = vx·t = 33.83·2.51 = 84.92 m
Answer
x = 84.92 m
6.Projectile motion
Answer: x = 151 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 25.07 m/s, vy = 29.88 m/s
Time to land on the roof
Larger root: the ball is descending.
2 = 29.88·t − 4.905·t²
t = (29.88 + √(29.88² − 2·9.81·2))/9.81 = 6.023 s
Horizontal distance
x = vx·t = 25.07·6.023 = 151 m
Answer
x = 151 m
7.Work & energy
Answer: P = 24.69 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 2000·9.81 = 19620 N
mg·sin θ = 19620·sin 2° = 684.7 N
F = 684.7 + 550 = 1235 N
Power
v = 72/3.6 = 20 m/s
P = F·v = 1235·20 = 24695 W = 24.69 kW
Answer
P = 24.69 kW
8.Work & energy
Answer: x = 37.59 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 9.81·(4 − 0.2·2) = 35.32 J
Maximum compression
½kx² = 35.32 → x = √(2·35.32/500) = 0.3759 m = 37.59 cm
Answer
x = 37.59 cm
9.Momentum & collisions
Answer: v = 116.6 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.12) = 1.534 m/s
Collision
m·v = (m + M)·V → v = (0.02 + 1.5)·1.534/0.02 = 116.6 m/s
Answer
v = 116.6 m/s
10.Momentum & collisions
Answer: v1 = 30.3 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.25·7.5 = 386.3 kN
Answer
F = 386.3 kN
12.Hydrostatic force
Answer: F = 113.1 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2.5/2 = 2.25 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2.25·5 = 113.1 kN
Answer
F = 113.1 kN
13.Continuity & Bernoulli
Answer: p2 = 123.8 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 40 + 273.15 = 313.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 313.1/923.1 = 66.08 %
Answer
ηmax = 66.08 %
18.Heat engines & refrigerators
Answer: Q̇L = 360.7 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 900 + 273.15 = 1173 K
T0 = 27 + 273.15 = 300.1 K
TL = -20 + 273.15 = 253.1 K
Engine work
η = 1 − 300.1/1173 = 0.7442
Ẇ = 0.7442·90 = 66.97 kW
Heat removed by the refrigerator
COPR = 253.1/(300.1 − 253.1) = 5.386
Q̇L = 5.386·66.97 = 360.7 kW
Answer
Q̇L = 360.7 kW
19.Waves, sound & optics
Answer: di = 20 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/15 − 1/60
di = 20 cm
Ray diagram
real, on the far side of the lens
Answer
di = 20 cm
20.Waves, sound & optics
Answer: di2 = 7.5 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.