Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 45 km/h brakes with a constant deceleration of 3 m/s² until it stops. Find the braking distance s.
v₀ = 45 km/ha = −3 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 11 m/s from the edge of a roof 20 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 11 m/sh₀ = 20 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 35 kg sled is pulled across level snow by a rope at 30° above the horizontal with a force of 140 N. The coefficient of kinetic friction is 0.4. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 35 kgF = 140 Nθ = 30°μ = 0.4g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 1.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5.5 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 1.5 kgm2 = 5.5 kgμ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 55° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 26 m/sθ = 55°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 18 m/s and 60° above the horizontal from the top of a 5 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 18 m/sθ = 60°h = 5 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A 2.5 kg block slides 2 m down a slope at 20° to the horizontal, with a coefficient of kinetic friction of 0.2. Find the work Wf done against friction.
m = 2.5 kgθ = 20°μ = 0.2d = 2 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 0.5 kg cart is released from rest at a height of 11.3 m on a smooth track that leads into a vertical circular loop of radius 2.5 m. Find the speed v of the cart at the top of the loop.
m = 0.5 kgh = 11.3 mR = 2.5 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 2 kg glider moving at 8 m/s makes a perfectly elastic head-on collision with a 4.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 2 kgm2 = 4.5 kgv1 = 8 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.2 kg ball hits a wall at 15 m/s and bounces straight back at 16 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
m = 0.2 kgvin = 15 m/svout = 16 m/sΔt = 5 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of oil, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1.5 mH = 2 mb = 3 mρ = 880 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal venturi meter with an inlet diameter of 200 mm and a throat diameter of 150 mm. The pressure at the inlet is 30 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 7 m. At section 1 the pressure is 230 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 500 °C and a cold reservoir at 5 °C. It takes in 1200 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 500 °CTL = 5 °CQH = 1200 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -25 °C in a kitchen at 28 °C, removing heat from the cold space at 5 kW. Find the minimum power input Ẇmin.
TH = 28 °CTL = -25 °CQ̇L = 5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A string fixed at both ends is 1.5 m long; waves travel on it at 180 m/s. Find the frequency f1 of its fundamental (first harmonic).
v = 180 m/sn = 1L = 1.5 m
f1 = Hz
20.Waves, sound & opticsHard
A diffraction grating has 500 lines per millimetre. Light of wavelength 405 nm falls on it at right angles. What is the highest order mmax of bright maximum that can be seen?
N = 500 mm⁻¹λ = 405 nm
mmax =
3Solutions
1.Kinematics
Answer: s = 26.04 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 45/3.6 = 12.5 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 12.5²/(2·3) = 26.04 m
Answer
s = 26.04 m
2.Kinematics
Answer: hmax = 26.17 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 11²/(2·9.81) = 6.167 m
Height above the ground
hmax = 20 + 6.167 = 26.17 m
Answer
hmax = 26.17 m
3.Newton’s laws
Answer: a = 0.3401 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 343.4 − 140·sin 30° = 273.4 N
Horizontal forces
m·a = F·cos θ − μ·N = 121.2 − 109.3
a = 11.9/35 = 0.3401 m/s²
Answer
a = 0.3401 m/s²
4.Newton’s laws
Answer: T = 14.45 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 26·cos 55° = 14.91 m/s
vy = v0·sin θ = 26·sin 55° = 21.3 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·21.3/9.81 = 4.342 s
Horizontal distance
x = vx·t = 14.91·4.342 = 64.75 m
Answer
x = 64.75 m
6.Projectile motion
Answer: α = 64.02 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 18·cos 60° = 9 m/s
vy0 = 18·sin 60° = 15.59 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(15.59² + 2·9.81·5) = 18.47 m/s
Impact angle
tan α = vy/vx = 18.47/9 → α = 64.02°
Answer
α = 64.02°
7.Work & energy
Answer: Wf = 9.218 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 24.53·0.9397 = 23.05 N
F = μN = 0.2·23.05 = 4.609 N
Work against friction
Wf = F·d = 4.609·2 = 9.218 J
Answer
Wf = 9.218 J
8.Work & energy
Answer: v = 11.12 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(11.3 − 5) = 123.6 m²/s²
v = 11.12 m/s
Answer
v = 11.12 m/s
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v′2 = 4.923 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 4.5)/(2 + 4.5)·8 = −3.077 m/s
v′2 = 2·2/(2 + 4.5)·8 = 4.923 m/s
Answer
v′2 = 4.923 m/s
10.Momentum & collisions
Answer: Favg = 1240 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.2·(16 + 15) = 6.2 N·s
Average force
Favg = J/Δt = 6.2/0.005 = 1240 N
Answer
Favg = 1240 N
11.Hydrostatic force
Answer: F = 55.18 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2.5/2 = 2.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.25·2.5 = 55.18 kN
Answer
F = 55.18 kN
12.Hydrostatic force
Answer: F = 129.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2/2 = 2.5 m
A = H·b = 2·3 = 6 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·2.5·6 = 129.5 kN
Answer
F = 129.5 kN
13.Continuity & Bernoulli
Answer: Q = 165.6 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(150/200)² = 0.5625·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 308.1 K, T2 = 423.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(200/250)·(423.1/308.1) = 10.99 L
Answer
V2 = 10.99 L
17.Heat engines & refrigerators
Answer: Wmax = 768.3 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/773.1 = 64.02 %
Maximum work
Wmax = ηmax·QH = 0.6402·1200 = 768.3 kJ
Answer
Wmax = 768.3 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 1.068 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 5/4.682 = 1.068 kW
Answer
Ẇmin = 1.068 kW
19.Waves, sound & optics
Answer: f1 = 60 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·1.5/1 = 3 m
Frequency
f = v/λ = 180/3 = 60 Hz
Answer
f1 = 60 Hz
20.Waves, sound & optics
Answer: mmax = 4
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …