Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 50 km/h sees an obstacle. Her reaction time is 0.9 s, after which the car brakes with a constant deceleration of 7 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 50 km/htr = 0.9 sa = −7 m/s²
d = m
2.KinematicsHard
Ball A is dropped from rest from a height of 10 m. At the same instant ball B is thrown straight up from the ground directly below at 30 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 10 mv0B = 30 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 2 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 2 kgθ = 45°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 10 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 10 m/sθ = 25°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is kicked from level ground at 36 m/s and 35° above the horizontal towards a wall 87 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 36 m/sθ = 35°x = 87 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 15° above horizontal from the top of a 15 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 16 m/sθ = 15°h = 15 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 2 kg ball hangs on a light string of length 3 m. It is pulled aside until the string makes 45° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 2 kgL = 3 mθ = 45°g = 9.81 m/s²
T = N
8.Work & energyHard
A 10 kg block is released from rest at height 2 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 1.5 m long (μ = 0.1) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 10 kgh = 2 mL = 1.5 mμ = 0.1k = 500 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 1200 kg car moving at 22 m/s runs into a stationary 1800 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1200 kgv1 = 22 m/sm2 = 1800 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 17 m/s and bounces straight back at 14 m/s. The contact lasts 10 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.5 kgvin = 17 m/svout = 14 m/sΔt = 10 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 2 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 75 mm to 40 mm. In the wide section the pressure is 120 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A fountain nozzle points straight up. Just below the nozzle the supply pipe has a diameter of 100 mm and a gauge pressure of 130 kPa. The nozzle exit diameter is 25 mm, and the height difference across the nozzle is negligible. Ignoring losses and air resistance, find the height H the jet rises above the nozzle. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 775 °C and a cold reservoir at 35 °C. It takes in 3900 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 775 °CTL = 35 °CQH = 3900 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 5 °C in a kitchen at 25 °C, removing heat from the cold space at 4.5 kW. Find the minimum power input Ẇmin.
TH = 25 °CTL = 5 °CQ̇L = 4.5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A source of 400 Hz moves at 30 m/s away from a stationary observer. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 400 Hzv = 343 m/svs = 30 m/s
f′ = Hz
20.Waves, sound & opticsHard
Light of wavelength 500 nm passes through a single slit 0.1 mm wide. Find the width w of the central bright maximum on a screen 1.5 m away (between the first dark fringes on either side).
λ = 500 nma = 0.1 mmL = 1.5 m
w = mm
3Solutions
1.Kinematics
Answer: d = 26.28 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Reaction distance
d1 = v₀·tr = 13.89·0.9 = 12.5 m
Braking distance
d2 = v₀²/(2a) = 13.89²/(2·7) = 13.78 m
Total
d = 12.5 + 13.78 = 26.28 m
Answer
d = 26.28 m
2.Kinematics
Answer: t = 0.3333 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
10 − ½g·t² = 30·t − ½g·t² → t = 10/30 = 0.3333 s
Answer
t = 0.3333 s
3.Newton’s laws
Answer: a = 4.856 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 25° + 0.15·cos 25°) = 5.48 m/s²
Distance
d = v₀²/(2a) = 10²/(2·5.48) = 9.125 m
Answer
d = 9.125 m
5.Projectile motion
Answer: y = 18.23 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 36·cos 35° = 29.49 m/s
t = x/vx = 87/29.49 = 2.95 s
Height at that time
y = 20.65·2.95 − ½·9.81·2.95² = 18.23 m
Answer
y = 18.23 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: x = 34.33 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 16·cos 15° = 15.45 m/s
vy = v0·sin θ = 16·sin 15° = 4.141 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 15 + 4.141·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (4.141 + √(17.15 + 294.3))/9.81 = 2.221 s
Horizontal distance
x = vx·t = 15.45·2.221 = 34.33 m
Answer
x = 34.33 m
7.Work & energy
Answer: T = 31.11 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·3·(1 − cos 45°) = 17.24 m²/s²
Forces at the bottom
m·g = 2·9.81 = 19.62 N
T = mg + mv²/L = 19.62 + 2·17.24/3 = 31.11 N
Answer
T = 31.11 N
Check: T = mg(3 − 2cos θ) = 31.11 N.
8.Work & energy
Answer: v = 6.025 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 98.1·(2 − 0.1·1.5) = 181.5 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·1.85) = 6.025 m/s
Answer
v = 6.025 m/s
9.Momentum & collisions
Answer: ΔK = 174240 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1200·22/3000 = 8.8 m/s
Kinetic energy before and after
Kbefore = ½·1200·22² = 290400 J
Kafter = ½·3000·8.8² = 116160 J
Energy lost
ΔK = 290400 − 116160 = 174240 J
Answer
ΔK = 174240 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: J = 15.5 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(14 + 17) = 15.5 N·s
Answer
J = 15.5 N·s
11.Hydrostatic force
Answer: F = 176.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·3 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·6 = 176.6 kN
Answer
F = 176.6 kN
12.Hydrostatic force
Answer: ycp = 4.083 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2/2 = 4 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·4·3 = 120.7 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 1.5·2³/12 = 1 m⁴
ycp = yc + Ic/(yc·A) = 4 + 1/(4·3) = 4.083 m
Answer
ycp = 4.083 m
13.Continuity & Bernoulli
Answer: p2 = 97.28 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Exit velocity
β = 25/100 = 0.25
v2 = √(2p1/(ρ(1 − β⁴))) = √(2·130000/(1000·0.9961)) = 16.16 m/s
Height of the jet
Bernoulli along the jet: at the top the velocity is zero and the pressure is atmospheric again.
H = v2²/(2g) = 16.16²/(2·9.81) = 13.3 m
Answer
H = 13.3 m
15.Ideal gas law
Answer: P = 5149 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 490/44.01 = 11.13 mol
T = 5 + 273.15 = 278.1 K
Pressure
P = nRT/V = 11.13·8.314·278.1/0.005 = 5149 kPa
Answer
P = 5149 kPa
16.Ideal gas law
Answer: V2 = 3.257 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 298.1 K, T2 = 453.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(150/700)·(453.1/298.1) = 3.257 L
Answer
V2 = 3.257 L
17.Heat engines & refrigerators
Answer: Wmax = 2753 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 775 + 273.15 = 1048 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 308.1/1048 = 70.6 %
Maximum work
Wmax = ηmax·QH = 0.706·3900 = 2753 kJ
Answer
Wmax = 2753 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.3236 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 4.5/13.91 = 0.3236 kW
Answer
Ẇmin = 0.3236 kW
19.Waves, sound & optics
Answer: f′ = 367.8 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …