Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 1.5 m/s² along a runway. Find its speed v after 1100 m.
v₀ = 0a = 1.5 m/s²s = 1100 m
v = m/s
2.KinematicsHard
A tram starts from rest and accelerates at 1.5 m/s² for 8 s, then runs at constant speed for 18 s, and finally brakes at 3.5 m/s² until it stops. Find the total distance s between the two stops.
a1 = 1.5 m/s²t1 = 8 st2 = 18 sa3 = −3.5 m/s²
s = m
3.Newton’s lawsMedium
A 50 kg box is pushed up a ramp at 15° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the pushing force F.
m = 50 kgθ = 15°μ = 0.15g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A 3.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5 kg mass. The coefficient of kinetic friction between block and table is 0.3. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 3.5 kgm2 = 5 kgμ = 0.3g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 30 m/s and 35° above the horizontal towards a wall 26 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 30 m/sθ = 35°x = 26 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 30° above horizontal from the top of a 30 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 33 m/sθ = 30°h = 30 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 5 kg block slides 18 m down a slope at 20° to the horizontal, with a coefficient of kinetic friction of 0.25. Find the work Wf done against friction.
m = 5 kgθ = 20°μ = 0.25d = 18 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 5 kg cart is released from rest at a height of 14 m on a smooth track that leads into a vertical circular loop of radius 4 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 5 kgh = 14 mR = 4 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 16 kg projectile moving horizontally at 38 m/s explodes into two fragments that move along the same line. The 15 kg fragment continues forwards at 91 m/s. Find the velocity v′2 of the 1 kg fragment (positive in the original direction).
M = 16 kgu = 38 m/sm1 = 15 kgv′1 = 91 m/sm2 = 1 kg
v′2 = m/s
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 21 m/s and bounces straight back at 16 m/s. The contact lasts 20 ms. Find the average force Favg of the wall on the ball.
m = 0.55 kgvin = 21 m/svout = 16 m/sΔt = 20 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A pitot-static tube in a wind tunnel reads a difference of 200 Pa between the stagnation pressure and the static pressure. The air density is 1.2 kg/m³. Find the air speed v.
p0 − p = 200 Paρ = 1.2 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 100 mm to 40 mm while rising 4 m. At section 1 the pressure is 330 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 300 °C and rejects heat to the surroundings at 30 °C. Its actual thermal efficiency is 33%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 300 °CTL = 30 °Cη = 33%
ηII = %
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 130 kW of heat from a source at 900 °C and rejects heat to the surroundings at 20 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -25 °C and also rejects heat to the surroundings at 20 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 900 °CT0 = 20 °CTL = -25 °CQ̇H = 130 kW
Q̇L = kW
19.Waves, sound & opticsMedium
A pipe closed at one end is 1 m long. The speed of sound is 343 m/s. Find the frequency f1 of its fundamental (first harmonic).
v = 343 m/sn = 1L = 1 m
f1 = Hz
20.Waves, sound & opticsHard
Light of wavelength 600 nm falls at right angles on a grating with 200 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 200 mm⁻¹λ = 600 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: v = 57.45 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·1.5·1100) = 57.45 m/s
Answer
v = 57.45 m/s
(206.8 km/h)
2.Kinematics
Answer: s = 284.6 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 1.5·8 = 12 m/s
Distance of each phase
s1 = ½·1.5·8² = 48 m
s2 = 12·18 = 216 m
s3 = 12²/(2·3.5) = 20.57 m
Total distance
s = 48 + 216 + 20.57 = 284.6 m
Answer
s = 284.6 m
3.Newton’s laws
Answer: F = 198 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 127 + 71.07 = 198 N
Answer
F = 198 N
4.Newton’s laws
Answer: a = 4.559 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 30·cos 35° = 24.57 m/s
t = x/vx = 26/24.57 = 1.058 s
Height at that time
y = 17.21·1.058 − ½·9.81·1.058² = 12.71 m
Answer
y = 12.71 m
The ball is still rising at the wall.
6.Projectile motion
Answer: x = 133.5 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 33·cos 30° = 28.58 m/s
vy = v0·sin θ = 33·sin 30° = 16.5 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 30 + 16.5·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (16.5 + √(272.2 + 588.6))/9.81 = 4.673 s
Horizontal distance
x = vx·t = 28.58·4.673 = 133.5 m
Answer
x = 133.5 m
7.Work & energy
Answer: Wf = 207.4 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 49.05·0.9397 = 46.09 N
F = μN = 0.25·46.09 = 11.52 N
Work against friction
Wf = F·d = 11.52·18 = 207.4 J
Answer
Wf = 207.4 J
8.Work & energy
Answer: N = 98.1 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(14 − 8) = 117.7 m²/s²
Forces at the top
m·g = 5·9.81 = 49.05 N
N = mv²/R − mg = 5·117.7/4 − 49.05 = 98.1 N
Answer
N = 98.1 N
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v′2 = −757 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 16·38 = 608 kg·m/s
Momentum after
608 = 15·91 + 1·v′2
v′2 = (608 − 1365)/1 = −757 m/s
Answer
v′2 = −757 m/s
The minus sign means the second fragment flies backwards.
10.Momentum & collisions
Answer: Favg = 1018 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(16 + 21) = 20.35 N·s
Average force
Favg = J/Δt = 20.35/0.02 = 1018 N
Answer
Favg = 1018 N
11.Hydrostatic force
Answer: F = 110.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 3/2 = 2.5 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·4.5 = 110.4 kN
Answer
F = 110.4 kN
12.Hydrostatic force
Answer: F = 110.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2.5/2 = 2.25 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.25·5 = 110.4 kN
Answer
F = 110.4 kN
13.Continuity & Bernoulli
Answer: v = 18.26 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·200/1.2) = 18.26 m/s
Answer
v = 18.26 m/s
14.Continuity & Bernoulli
Answer: p2 = 214.6 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 308.1 K, T2 = 393.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(200/550)·(393.1/308.1) = 0.9279 L
Answer
V2 = 0.9279 L
17.Heat engines & refrigerators
Answer: ηII = 70.05 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 300 + 273.15 = 573.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηCarnot = 1 − 303.1/573.1 = 47.11 %
Second-law efficiency
ηII = η/ηCarnot = 33/47.11 = 70.05 %
Answer
ηII = 70.05 %
18.Heat engines & refrigerators
Answer: Q̇L = 537.7 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 900 + 273.15 = 1173 K
T0 = 20 + 273.15 = 293.1 K
TL = -25 + 273.15 = 248.1 K
Engine work
η = 1 − 293.1/1173 = 0.7501
Ẇ = 0.7501·130 = 97.52 kW
Heat removed by the refrigerator
COPR = 248.1/(293.1 − 248.1) = 5.514
Q̇L = 5.514·97.52 = 537.7 kW
Answer
Q̇L = 537.7 kW
19.Waves, sound & optics
Answer: f1 = 85.75 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 4L/n = 4·1/1 = 4 m
Frequency
f = v/λ = 343/4 = 85.75 Hz
Answer
f1 = 85.75 Hz
20.Waves, sound & optics
Answer: θ1 = 6.892 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …