Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 3.5 m/s² along a runway. Find its speed v after 1600 m.
v₀ = 0a = 3.5 m/s²s = 1600 m
v = m/s
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 24 m/s² for 2 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 24 m/s²t1 = 2 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 35 kg sled is pulled across level snow by a rope at 40° above the horizontal with a force of 170 N. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 35 kgF = 170 Nθ = 40°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 9 kg block on a ramp at 20° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 8.5 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 9 kgm2 = 8.5 kgθ = 20°μ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 30° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 10 m/sθ = 30°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 16 m/s and 15° above the horizontal from the top of a 55 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 16 m/sθ = 15°h = 55 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A 1 kg block slides 11 m down a slope at 25° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 1 kgθ = 25°μ = 0.3d = 11 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 10 kg block rests on a rough horizontal table (μ = 0.1). A light string runs from it over a smooth pulley at the edge of the table to a hanging 3 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 3 m.
m1 = 10 kgm2 = 3 kgμ = 0.1d = 3 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 3.5 kg glider moving at 12 m/s makes a perfectly elastic head-on collision with a 3 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 3.5 kgm2 = 3 kgv1 = 12 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.4 kg ball hits a wall at 25 m/s and bounces straight back at 10 m/s. The contact lasts 5 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.4 kgvin = 25 m/svout = 10 m/sΔt = 5 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1 m wide sits in the wall of a tank of seawater, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 100 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 100 mm, throat 50 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 130 mm. The discharge coefficient is 0.97. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 550 °C and a cold reservoir at 35 °C. Find the highest possible thermal efficiency ηmax.
TH = 550 °CTL = 35 °C
ηmax = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 650 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 40 °C. Both engines have the same thermal efficiency. Find Tm in °C.
TH = 650 °CTL = 40 °C
Tm = °C
19.Waves, sound & opticsMedium
A string fixed at both ends must have its fundamental (first harmonic) at 83 Hz; waves travel on it at 200 m/s. Find its length L.
v = 200 m/sn = 1f1 = 83 Hz
L = m
20.Waves, sound & opticsHard
An object is 40 cm in front of a concave mirror with a radius of curvature of 60 cm. Find the magnification m (negative for an inverted image).
do = 40 cmR = 60 cm
m =
3Solutions
1.Kinematics
Answer: v = 105.8 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·3.5·1600) = 105.8 m/s
Answer
v = 105.8 m/s
(381 km/h)
2.Kinematics
Answer: hmax = 165.4 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 24·2 = 48 m/s
h₁ = ½·24·2² = 48 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 48²/(2·9.81) = 117.4 m
hmax = 48 + 117.4 = 165.4 m
Answer
hmax = 165.4 m
3.Newton’s laws
Answer: a = 2.383 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 343.4 − 170·sin 40° = 234.1 N
Horizontal forces
m·a = F·cos θ − μ·N = 130.2 − 46.82
a = 83.41/35 = 2.383 m/s²
Answer
a = 2.383 m/s²
4.Newton’s laws
Answer: T = 67.63 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 83.39 N
m₁·g·sin θ = 30.2 N
μ·m₁·g·cos θ = 20.74 N
Acceleration of the system
a = (83.39 − 30.2 − 20.74)/17.5 = 1.854 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 8.5·(9.81 − 1.854) = 67.63 N
Answer
T = 67.63 N
5.Projectile motion
Answer: t = 1.019 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 10·cos 30° = 8.66 m/s
vy = v0·sin θ = 10·sin 30° = 5 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·5/9.81 = 1.019 s
Answer
t = 1.019 s
6.Projectile motion
Answer: α = 64.98 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 16·cos 15° = 15.45 m/s
vy0 = 16·sin 15° = 4.141 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(4.141² + 2·9.81·55) = 33.11 m/s
Impact angle
tan α = vy/vx = 33.11/15.45 → α = 64.98°
Answer
α = 64.98°
7.Work & energy
Answer: Wf = 29.34 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 9.81·0.9063 = 8.891 N
F = μN = 0.3·8.891 = 2.667 N
Work against friction
Wf = F·d = 2.667·11 = 29.34 J
Answer
Wf = 29.34 J
8.Work & energy
Answer: v = 3.009 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 29.43·3 = 88.29 J
μ·m₁g·d = 0.1·98.1·3 = 29.43 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 58.86 → v = √(2·58.86/13) = 3.009 m/s
Answer
v = 3.009 m/s
9.Momentum & collisions
Answer: v′1 = 0.9231 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3.5 − 3)/(3.5 + 3)·12 = 0.9231 m/s
v′2 = 2·3.5/(3.5 + 3)·12 = 12.92 m/s
Answer
v′1 = 0.9231 m/s
10.Momentum & collisions
Answer: J = 14 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.4·(10 + 25) = 14 N·s
Answer
J = 14 N·s
11.Hydrostatic force
Answer: F = 19.62 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1/2 = 1 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1·2 = 19.62 kN
Answer
F = 19.62 kN
12.Hydrostatic force
Answer: F = 94.27 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 2.5/2 = 3.75 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·3.75·2.5 = 94.27 kN
Answer
F = 94.27 kN
13.Continuity & Bernoulli
Answer: p2 = 32.5 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.13 = 16069 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 308.1/823.1 = 62.56 %
Answer
ηmax = 62.56 %
18.Heat engines & refrigerators
Answer: Tm = 264.5 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 40 + 273.15 = 313.1 K
Equal efficiencies
1 − Tm/TH = 1 − TL/Tm gives Tm² = TH·TL.
Tm = √(923.1·313.1) = 537.7 K = 264.5 °C
Answer
Tm = 264.5 °C
19.Waves, sound & optics
Answer: L = 1.205 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 200/83 = 2.41 m
Length
L = nλ/2 = 1·2.41/2 = 1.205 m
Answer
L = 1.205 m
20.Waves, sound & optics
Answer: m = −3
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.