Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 2.75 m/s² along a runway. Find its speed v after 1500 m.
v₀ = 0a = 2.75 m/s²s = 1500 m
v = m/s
2.KinematicsHard
A tram starts from rest and accelerates at 3 m/s² for 8 s, then runs at constant speed for 22 s, and finally brakes at 3 m/s² until it stops. Find the total distance s between the two stops.
a1 = 3 m/s²t1 = 8 st2 = 22 sa3 = −3 m/s²
s = m
3.Newton’s lawsMedium
Masses of 6 kg and 0.5 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 6 kgm2 = 0.5 kgg = 9.81 m/s²
T = N
4.Newton’s lawsHard
A 6 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 6 kgm2 = 2 kgμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 32 m/s and 70° above the horizontal towards a wall 54 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 32 m/sθ = 70°x = 54 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 40° above horizontal from the top of a 25 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 12 m/sθ = 40°h = 25 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A car travelling at 70 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.8. Find the stopping distance d.
v = 70 km/hμ = 0.8g = 9.81 m/s²
d = m
8.Work & energyHard
A 5 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.3) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 5 kgh = 5 mL = 3 mμ = 0.3k = 1000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 1100 kg car moving at 7 m/s runs into a stationary 1800 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 1100 kgv1 = 7 m/sm2 = 1800 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
At a crossing a 1100 kg car travelling east at 10 m/s collides with a 1000 kg car travelling north at 8 m/s. The cars lock together. Find the speed v′ of the wreck just after the collision.
m1 = 1100 kgv1 = 10 m/s (E)m2 = 1000 kgv2 = 8 m/s (N)
v′ = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 0.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal venturi meter with an inlet diameter of 200 mm and a throat diameter of 150 mm. The pressure at the inlet is 56 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
A horizontal venturi meter (inlet 200 mm, throat 100 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 330 mm. The discharge coefficient is 0.95. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A reversible (Carnot) heat engine takes in 500 kJ of heat from a reservoir at 600 °C and rejects 174 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 600 °CQH = 500 kJQL = 174 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat pump delivers 17 kW of heat to a heating system at 22 °C, taking heat from a source at 0 °C. Its actual COP is 50% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 22 °CTL = 0 °CηII = 50%Q̇H = 17 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A string fixed at both ends is 1.5 m long; waves travel on it at 300 m/s. Find the frequency f5 of its harmonic number 5.
v = 300 m/sn = 5L = 1.5 m
f5 = Hz
20.Waves, sound & opticsHard
Two slits 0.1 mm apart are lit with monochromatic light. On a screen 2.5 m away, bright fringe number 3 lies 44.17 mm from the central fringe. Find the wavelength λ.
d = 0.1 mmL = 2.5 my3 = 44.17 mmm = 3
λ = nm
3Solutions
1.Kinematics
Answer: v = 90.83 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·2.75·1500) = 90.83 m/s
Answer
v = 90.83 m/s
(327 km/h)
2.Kinematics
Answer: s = 720 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 3·8 = 24 m/s
Distance of each phase
s1 = ½·3·8² = 96 m
s2 = 24·22 = 528 m
s3 = 24²/(2·3) = 96 m
Total distance
s = 96 + 528 + 96 = 720 m
Answer
s = 720 m
3.Newton’s laws
Answer: T = 9.055 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (6 − 0.5)·9.81/(6 + 0.5) = 8.301 m/s²
Tension from the lighter mass
T − m2·g = m2·a → T = 0.5·(9.81 + 8.301) = 9.055 N
Answer
T = 9.055 N
4.Newton’s laws
Answer: a = 0.981 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 32·cos 70° = 10.94 m/s
t = x/vx = 54/10.94 = 4.934 s
Height at that time
y = 30.07·4.934 − ½·9.81·4.934² = 28.96 m
Answer
y = 28.96 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: x = 29.2 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 12·cos 40° = 9.193 m/s
vy = v0·sin θ = 12·sin 40° = 7.713 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 25 + 7.713·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (7.713 + √(59.5 + 490.5))/9.81 = 3.177 s
Horizontal distance
x = vx·t = 9.193·3.177 = 29.2 m
Answer
x = 29.2 m
7.Work & energy
Answer: d = 24.09 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 70/3.6 = 19.44 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 19.44²/(2·0.8·9.81) = 24.09 m
Answer
d = 24.09 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 8.969 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(5 − 0.3·3) = 201.1 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·4.1) = 8.969 m/s
Answer
v = 8.969 m/s
9.Momentum & collisions
Answer: ΔK/K = 62.07 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1100·7/2900 = 2.655 m/s
Kinetic energy before and after
Kbefore = ½·1100·7² = 26950 J
Kafter = ½·2900·2.655² = 10222 J
Fraction lost
ΔK/K = 16728/26950 = 62.07 %
Answer
ΔK/K = 62.07 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v′ = 6.477 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(150/200)² = 0.5625·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.33 = 40790 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 343.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(300/650)·(343.1/288.1) = 5.496 L
Answer
V2 = 5.496 L
17.Heat engines & refrigerators
Answer: TL = 30.71 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 600 + 273.15 = 873.1 K
Reversible heat ratio
TL = TH·QL/QH = 873.1·174/500 = 303.9 K = 30.71 °C
Answer
TL = 30.71 °C
18.Heat engines & refrigerators
Answer: Ẇ = 2.534 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 22 + 273.15 = 295.1 K
TL = 0 + 273.15 = 273.1 K
Carnot and actual COP
COPmax = 295.1/(295.1 − 273.1) = 13.42
COP = 0.5·13.42 = 6.708
Power input
Ẇ = Q̇H/COP = 17/6.708 = 2.534 kW
Answer
Ẇ = 2.534 kW
19.Waves, sound & optics
Answer: f5 = 500 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·1.5/5 = 0.6 m
Frequency
f = v/λ = 300/0.6 = 500 Hz
Answer
f5 = 500 Hz
20.Waves, sound & optics
Answer: λ = 588.9 nm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …