Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 80 km/h brakes with a constant deceleration of 5 m/s² until it stops. How long does braking take? Find t.
v₀ = 80 km/ha = −5 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 8 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 8 m/sh₀ = 25 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 2.5 m/s and comes to rest after 3.2 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 2.5 m/sd = 3.2 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 15° with a speed of 8.5 m/s. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 8.5 m/sθ = 15°μ = 0.1g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is kicked from level ground at 24 m/s and 70° above the horizontal towards a wall 26 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 24 m/sθ = 70°x = 26 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 30 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 19 m/sθ = 45°h = 30 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.4. Find its speed v after it has slid 6 m along the slope.
θ = 45°μ = 0.4d = 6 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A spring of stiffness 500 N/m at the bottom of a 15° slope is compressed by 15 cm against a 1 kg block and released. The coefficient of kinetic friction between block and slope is 0.15. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 1.5 kg glider moving at 2 m/s makes a perfectly elastic head-on collision with a 4.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 1.5 kgm2 = 4.5 kgv1 = 2 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.2 kg ball hits a wall at 18 m/s and bounces straight back at 20 m/s. The contact lasts 20 ms. Find the average force Favg of the wall on the ball.
m = 0.2 kgvin = 18 m/svout = 20 m/sΔt = 20 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of glycerin, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 75 mm. In the wide section the pressure is 270 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 10 m. At section 1 the pressure is 210 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 575 °C and a cold reservoir at 5 °C. Find the highest possible thermal efficiency ηmax.
TH = 575 °CTL = 5 °C
ηmax = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 850 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 30 °C. Both engines produce the same work. Find Tm in °C.
TH = 850 °CTL = 30 °C
Tm = °C
19.Waves, sound & opticsMedium
A string fixed at both ends is 0.6 m long; waves travel on it at 180 m/s. Find the frequency f5 of its harmonic number 5.
v = 180 m/sn = 5L = 0.6 m
f5 = Hz
20.Waves, sound & opticsHard
Light of wavelength 650 nm passes through a single slit 0.15 mm wide. Find the angle θ3 of dark fringe number 3 from the straight-through direction.
λ = 650 nma = 0.15 mmm = 3
θ3 = °
3Solutions
1.Kinematics
Answer: t = 4.444 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 80/3.6 = 22.22 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 22.22/5 = 4.444 s
Answer
t = 4.444 s
2.Kinematics
Answer: t = 3.216 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−25 = 8·t − ½·9.81·t²
4.905·t² − 8·t − 25 = 0
Solve the quadratic
Only the positive root is physical.
t = (8 + √(8² + 2·9.81·25))/9.81 = 3.216 s
Answer
t = 3.216 s
3.Newton’s laws
Answer: μ = 0.09955
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 2.5²/(2·3.2) = 0.9766 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 0.9766/9.81 = 0.09955
Answer
μ = 0.09955
4.Newton’s laws
Answer: d = 10.36 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 15° + 0.1·cos 15°) = 3.487 m/s²
Distance
d = v₀²/(2a) = 8.5²/(2·3.487) = 10.36 m
Answer
d = 10.36 m
5.Projectile motion
Answer: y = 22.22 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 24·cos 70° = 8.208 m/s
t = x/vx = 26/8.208 = 3.167 s
Height at that time
y = 22.55·3.167 − ½·9.81·3.167² = 22.22 m
Answer
y = 22.22 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: t = 4.197 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 19·cos 45° = 13.44 m/s
vy = v0·sin θ = 19·sin 45° = 13.44 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 30 + 13.44·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (13.44 + √(180.5 + 588.6))/9.81 = 4.197 s
Answer
t = 4.197 s
7.Work & energy
Answer: v = 7.067 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·6·(0.7071 − 0.4·0.7071)) = 7.067 m/s
Answer
v = 7.067 m/s
8.Work & energy
Answer: d = 1.42 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 15 cm = 0.15 m
½kx² = ½·500·0.15² = 5.625 J
Energy balance along the slope
m·g = 1·9.81 = 9.81 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 5.625/(9.81·(0.2588 + 0.15·0.9659)) = 1.42 m
Answer
d = 1.42 m
9.Momentum & collisions
Answer: v′2 = 1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1.5 − 4.5)/(1.5 + 4.5)·2 = −1 m/s
v′2 = 2·1.5/(1.5 + 4.5)·2 = 1 m/s
Answer
v′2 = 1 m/s
10.Momentum & collisions
Answer: Favg = 380 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.2·(20 + 18) = 7.6 N·s
Average force
Favg = J/Δt = 7.6/0.02 = 380 N
Answer
Favg = 380 N
11.Hydrostatic force
Answer: F = 55.18 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2.5/2 = 2.25 m
A = H·b = 2.5·1 = 2.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.25·2.5 = 55.18 kN
Answer
F = 55.18 kN
12.Hydrostatic force
Answer: F = 208.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1.5/2 = 3.75 m
A = H·b = 1.5·3 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·3.75·4.5 = 208.6 kN
Answer
F = 208.6 kN
13.Continuity & Bernoulli
Answer: p2 = 265.7 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 413.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(350/550)·(413.1/288.1) = 18.25 L
Answer
V2 = 18.25 L
17.Heat engines & refrigerators
Answer: ηmax = 67.21 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 575 + 273.15 = 848.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/848.1 = 67.21 %
Answer
ηmax = 67.21 %
18.Heat engines & refrigerators
Answer: Tm = 440 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 850 + 273.15 = 1123 K
TL = 30 + 273.15 = 303.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (1123 + 303.1)/2 = 713.2 K = 440 °C
Answer
Tm = 440 °C
19.Waves, sound & optics
Answer: f5 = 750 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.6/5 = 0.24 m
Frequency
f = v/λ = 180/0.24 = 750 Hz
Answer
f5 = 750 Hz
20.Waves, sound & optics
Answer: θ3 = 0.7449 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …