Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 18 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 3.5 m/s². How far from its starting point does the police car catch up? Find d.
vcar = 18 m/sapolice = 3.5 m/s²v0,police = 0
d = m
2.KinematicsHard
A ball is thrown straight up at 8 m/s from the edge of a roof 10 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 8 m/sh₀ = 10 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 20 kg sled is pulled across level snow by a rope at 30° above the horizontal with a force of 130 N. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 20 kgF = 130 Nθ = 30°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 2 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 0.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 2 kgm2 = 0.5 kgμ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 50° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 10 m/sθ = 50°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 30° above horizontal from the top of a 20 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 19 m/sθ = 30°h = 20 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A car travelling at 100 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 100 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
A spring of stiffness 5000 N/m at the bottom of a 15° slope is compressed by 20 cm against a 1 kg block and released. The coefficient of kinetic friction between block and slope is 0.2. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 2 kg glider moving at 10 m/s makes a perfectly elastic head-on collision with a 4 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 2 kgm2 = 4 kgv1 = 10 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.3 kg ball hits a wall at 28 m/s and bounces straight back at 12 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.3 kgvin = 28 m/svout = 12 m/sΔt = 20 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of seawater, with its top edge 1 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 200 mm to 75 mm. In the wide section the pressure is 180 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A closed water tank has compressed air above the water at a gauge pressure of 200 kPa. Water leaves through an opening with a diameter of 50 mm, 3 m below the water surface, into the open air. Ignoring losses, find the flow rate Q. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 500 °C and a cold reservoir at 35 °C. It takes in 2000 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 500 °CTL = 35 °CQH = 2000 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump delivers 14.5 kW of heat to a heating system at 45 °C, taking heat from a source at 0 °C. Its actual COP is 35% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 45 °CTL = 0 °CηII = 35%Q̇H = 14.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A source of 600 Hz moves at 30 m/s towards a stationary observer. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 600 Hzv = 343 m/svs = 30 m/s
f′ = Hz
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.52 and a cladding with n₂ = 1.5. Find its numerical aperture NA.
n1 = 1.52n2 = 1.5
NA =
3Solutions
1.Kinematics
Answer: d = 185.1 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·18/3.5 = 10.29 s
Distance
d = v·t = 18·10.29 = 185.1 m
Answer
d = 185.1 m
At that moment the police car moves at 2v = 36 m/s.
2.Kinematics
Answer: hmax = 13.26 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 8²/(2·9.81) = 3.262 m
Height above the ground
hmax = 10 + 3.262 = 13.26 m
Answer
hmax = 13.26 m
3.Newton’s laws
Answer: a = 3.989 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 196.2 − 130·sin 30° = 131.2 N
Horizontal forces
m·a = F·cos θ − μ·N = 112.6 − 32.8
a = 79.78/20 = 3.989 m/s²
Answer
a = 3.989 m/s²
4.Newton’s laws
Answer: T = 3.924 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 10·cos 50° = 6.428 m/s
vy = v0·sin θ = 10·sin 50° = 7.66 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 7.66²/(2·9.81) = 2.991 m
Answer
H = 2.991 m
6.Projectile motion
Answer: x = 52.78 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 19·cos 30° = 16.45 m/s
vy = v0·sin θ = 19·sin 30° = 9.5 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 20 + 9.5·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (9.5 + √(90.25 + 392.4))/9.81 = 3.208 s
Horizontal distance
x = vx·t = 16.45·3.208 = 52.78 m
Answer
x = 52.78 m
7.Work & energy
Answer: d = 56.18 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 100/3.6 = 27.78 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 27.78²/(2·0.7·9.81) = 56.18 m
Answer
d = 56.18 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: d = 22.55 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 20 cm = 0.2 m
½kx² = ½·5000·0.2² = 100 J
Energy balance along the slope
m·g = 1·9.81 = 9.81 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 100/(9.81·(0.2588 + 0.2·0.9659)) = 22.55 m
Answer
d = 22.55 m
9.Momentum & collisions
Answer: v′2 = 6.667 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 4)/(2 + 4)·10 = −3.333 m/s
v′2 = 2·2/(2 + 4)·10 = 6.667 m/s
Answer
v′2 = 6.667 m/s
10.Momentum & collisions
Answer: J = 12 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.3·(12 + 28) = 12 N·s
Answer
J = 12 N·s
11.Hydrostatic force
Answer: F = 88.29 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·3 = 88.29 kN
Answer
F = 88.29 kN
12.Hydrostatic force
Answer: ycp = 2.481 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2.5/2 = 2.25 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2.25·5 = 113.1 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 288.1 K, T2 = 463.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(100/700)·(463.1/288.1) = 1.148 L
Answer
V2 = 1.148 L
17.Heat engines & refrigerators
Answer: Wmax = 1203 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 500 + 273.15 = 773.1 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 308.1/773.1 = 60.14 %
Maximum work
Wmax = ηmax·QH = 0.6014·2000 = 1203 kJ
Answer
Wmax = 1203 kJ
18.Heat engines & refrigerators
Answer: Ẇ = 5.86 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 45 + 273.15 = 318.1 K
TL = 0 + 273.15 = 273.1 K
Carnot and actual COP
COPmax = 318.1/(318.1 − 273.1) = 7.07
COP = 0.35·7.07 = 2.474
Power input
Ẇ = Q̇H/COP = 14.5/2.474 = 5.86 kW
Answer
Ẇ = 5.86 kW
19.Waves, sound & optics
Answer: f′ = 657.5 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.