Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 72 km/h brakes with a constant deceleration of 7.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 72 km/ha = −7.5 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 13 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 13 m/sh₀ = 25 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 50 kg box is pushed up a ramp at 25° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.1. Use g = 9.81 m/s². Find the pushing force F.
m = 50 kgθ = 25°μ = 0.1g = 9.81 m/s²
F = N
4.Newton’s lawsHard
A 3.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 5.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 3.5 kgm2 = 5.5 kgμ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 50° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 16 m/sθ = 50°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 35° above horizontal from the top of a 60 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 35 m/sθ = 35°h = 60 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A car travelling at 60 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.4. Find the stopping distance d.
v = 60 km/hμ = 0.4g = 9.81 m/s²
d = m
8.Work & energyHard
A spring of stiffness 2000 N/m at the bottom of a 30° slope is compressed by 12 cm against a 0.5 kg block and released. The coefficient of kinetic friction between block and slope is 0.3. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 1100 kg car moving at 25 m/s runs into a stationary 1900 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1100 kgv1 = 25 m/sm2 = 1900 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
At a crossing a 1600 kg car travelling east at 17 m/s collides with a 1700 kg car travelling north at 13 m/s. The cars lock together. Find the direction θ of the wreck just after the collision, measured north of east.
m1 = 1600 kgv1 = 17 m/s (E)m2 = 1700 kgv2 = 13 m/s (N)
θ = °
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 3 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A pitot-static tube in a wind tunnel reads a difference of 1200 Pa between the stagnation pressure and the static pressure. The air density is 1.2 kg/m³. Find the air speed v.
p0 − p = 1200 Paρ = 1.2 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 75 mm to 50 mm while rising 6 m. At section 1 the pressure is 130 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 625 °C and a cold reservoir at 10 °C. Find the highest possible thermal efficiency ηmax.
TH = 625 °CTL = 10 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 5 °C in a kitchen at 25 °C, removing heat from the cold space at 1 kW. Find the minimum power input Ẇmin.
TH = 25 °CTL = 5 °CQ̇L = 1 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A small source sends sound equally in all directions. The level is 70 dB at 10 m from it. Find the level β2 at 100 m, ignoring absorption and reflections.
β1 = 70 dBr1 = 10 mr2 = 100 m
β2 = dB
20.Waves, sound & opticsHard
Light of wavelength 450 nm passes through a single slit 0.08 mm wide. Find the angle θ2 of dark fringe number 2 from the straight-through direction.
λ = 450 nma = 0.08 mmm = 2
θ2 = °
3Solutions
1.Kinematics
Answer: t = 2.667 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 72/3.6 = 20 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 20/7.5 = 2.667 s
Answer
t = 2.667 s
2.Kinematics
Answer: hmax = 33.61 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 13²/(2·9.81) = 8.614 m
Height above the ground
hmax = 25 + 8.614 = 33.61 m
Answer
hmax = 33.61 m
3.Newton’s laws
Answer: F = 251.7 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 207.3 + 44.45 = 251.7 N
Answer
F = 251.7 N
4.Newton’s laws
Answer: a = 5.995 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 16·cos 50° = 10.28 m/s
vy = v0·sin θ = 16·sin 50° = 12.26 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·12.26/9.81 = 2.499 s
Answer
t = 2.499 s
6.Projectile motion
Answer: x = 174.8 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 35·cos 35° = 28.67 m/s
vy = v0·sin θ = 35·sin 35° = 20.08 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 60 + 20.08·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (20.08 + √(403 + 1177))/9.81 = 6.099 s
Horizontal distance
x = vx·t = 28.67·6.099 = 174.8 m
Answer
x = 174.8 m
7.Work & energy
Answer: d = 35.39 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 60/3.6 = 16.67 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 16.67²/(2·0.4·9.81) = 35.39 m
Answer
d = 35.39 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: d = 3.864 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 12 cm = 0.12 m
½kx² = ½·2000·0.12² = 14.4 J
Energy balance along the slope
m·g = 0.5·9.81 = 4.905 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 14.4/(4.905·(0.5 + 0.3·0.866)) = 3.864 m
Answer
d = 3.864 m
9.Momentum & collisions
Answer: ΔK = 217708 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1100·25/3000 = 9.167 m/s
Kinetic energy before and after
Kbefore = ½·1100·25² = 343750 J
Kafter = ½·3000·9.167² = 126042 J
Energy lost
ΔK = 343750 − 126042 = 217708 J
Answer
ΔK = 217708 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: θ = 39.09 °
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum components
px = 1600·17 = 27200 kg·m/s
py = 1700·13 = 22100 kg·m/s
Direction
tan θ = py/px = 0.8125 → θ = 39.09°
Answer
θ = 39.09°
11.Hydrostatic force
Answer: F = 103 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·3 = 103 kN
Answer
F = 103 kN
12.Hydrostatic force
Answer: F = 111.2 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 3/2 = 2 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2·4.5 = 111.2 kN
Answer
F = 111.2 kN
13.Continuity & Bernoulli
Answer: v = 44.72 m/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·1200/1.2) = 44.72 m/s
Answer
v = 44.72 m/s
14.Continuity & Bernoulli
Answer: p2 = 63.02 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 308.1 K, T2 = 423.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(100/400)·(423.1/308.1) = 0.6866 L
Answer
V2 = 0.6866 L
17.Heat engines & refrigerators
Answer: ηmax = 68.47 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 625 + 273.15 = 898.1 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 283.1/898.1 = 68.47 %
Answer
ηmax = 68.47 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.0719 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 1/13.91 = 0.0719 kW
Answer
Ẇmin = 0.0719 kW
19.Waves, sound & optics
Answer: β2 = 50 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Intensity ratio
I₂/I₁ = (10/100)² = 0.01
New level
β₂ = 70 + 10·log₁₀(0.01) = 50 dB
Answer
β2 = 50 dB
Every doubling of the distance lowers the level by about 6 dB.
20.Waves, sound & optics
Answer: θ2 = 0.6446 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …