Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 90 km/h brakes with a constant deceleration of 6 m/s² until it stops. How long does braking take? Find t.
v₀ = 90 km/ha = −6 m/s²v = 0
t = s
2.KinematicsHard
A ball is thrown straight up at 20 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 20 m/sh₀ = 35 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 19 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 19 kgθ = 25°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 5 kgm2 = 3 kgμ = 0.1g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is kicked from level ground at 26 m/s and 40° above the horizontal towards a wall 54 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 26 m/sθ = 40°x = 54 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 30° above horizontal from the top of a 40 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 32 m/sθ = 30°h = 40 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 2 kg block slides 11 m down a slope at 45° to the horizontal, with a coefficient of kinetic friction of 0.1. Find the work Wf done against friction.
m = 2 kgθ = 45°μ = 0.1d = 11 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A spring of stiffness 2000 N/m at the bottom of a 25° slope is compressed by 12 cm against a 5 kg block and released. The coefficient of kinetic friction between block and slope is 0.3. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 5 kg glider moving at 9 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 5 kgm2 = 1 kgv1 = 9 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.3 kg ball hits a wall at 13 m/s and bounces straight back at 20 m/s. The contact lasts 10 ms. Find the average force Favg of the wall on the ball.
m = 0.3 kgvin = 13 m/svout = 20 m/sΔt = 10 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
A pitot-static tube in a water pipe reads a difference of 5 kPa between the stagnation pressure and the static pressure. Find the water velocity v at the tip.
p0 − p = 5 kPaρ = 1000 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 2 m. At section 1 the pressure is 100 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 700 °C and rejects heat to the surroundings at 15 °C. Its actual thermal efficiency is 35%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 700 °CTL = 15 °Cη = 35%
ηII = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -18 °C in a kitchen at 30 °C, removing heat from the cold space at 0.5 kW. Find the highest possible coefficient of performance COPmax.
TH = 30 °CTL = -18 °CQ̇L = 0.5 kW
COPmax =
19.Waves, sound & opticsMedium
A source of 600 Hz moves at 20 m/s towards a stationary observer. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 600 Hzv = 343 m/svs = 20 m/s
f′ = Hz
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.5 and a cladding with n₂ = 1.45. Find its numerical aperture NA.
n1 = 1.5n2 = 1.45
NA =
3Solutions
1.Kinematics
Answer: t = 4.167 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 90/3.6 = 25 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 25/6 = 4.167 s
Answer
t = 4.167 s
2.Kinematics
Answer: t = 5.399 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−35 = 20·t − ½·9.81·t²
4.905·t² − 20·t − 35 = 0
Solve the quadratic
Only the positive root is physical.
t = (20 + √(20² + 2·9.81·35))/9.81 = 5.399 s
Answer
t = 5.399 s
3.Newton’s laws
Answer: a = 2.368 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 26·cos 40° = 19.92 m/s
t = x/vx = 54/19.92 = 2.711 s
Height at that time
y = 16.71·2.711 − ½·9.81·2.711² = 9.256 m
Answer
y = 9.256 m
The ball is already on its way down at the wall.
6.Projectile motion
Answer: t = 4.92 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 32·cos 30° = 27.71 m/s
vy = v0·sin θ = 32·sin 30° = 16 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 40 + 16·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (16 + √(256 + 784.8))/9.81 = 4.92 s
Answer
t = 4.92 s
7.Work & energy
Answer: Wf = 15.26 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 19.62·0.7071 = 13.87 N
F = μN = 0.1·13.87 = 1.387 N
Work against friction
Wf = F·d = 1.387·11 = 15.26 J
Answer
Wf = 15.26 J
8.Work & energy
Answer: d = 0.4227 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 12 cm = 0.12 m
½kx² = ½·2000·0.12² = 14.4 J
Energy balance along the slope
m·g = 5·9.81 = 49.05 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 14.4/(49.05·(0.4226 + 0.3·0.9063)) = 0.4227 m
Answer
d = 0.4227 m
9.Momentum & collisions
Answer: v′2 = 15 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (5 − 1)/(5 + 1)·9 = 6 m/s
v′2 = 2·5/(5 + 1)·9 = 15 m/s
Answer
v′2 = 15 m/s
10.Momentum & collisions
Answer: Favg = 990 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.3·(20 + 13) = 9.9 N·s
Average force
Favg = J/Δt = 9.9/0.01 = 990 N
Answer
Favg = 990 N
11.Hydrostatic force
Answer: F = 165.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1.5/2 = 3.75 m
A = H·b = 1.5·3 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.75·4.5 = 165.5 kN
Answer
F = 165.5 kN
12.Hydrostatic force
Answer: ycp = 3.8 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1.5/2 = 3.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·3.75·2.25 = 84.84 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·5000/1000) = 3.162 m/s
Answer
v = 3.162 m/s
14.Continuity & Bernoulli
Answer: p2 = 78.96 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 700 + 273.15 = 973.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηCarnot = 1 − 288.1/973.1 = 70.39 %
Second-law efficiency
ηII = η/ηCarnot = 35/70.39 = 49.72 %
Answer
ηII = 49.72 %
18.Heat engines & refrigerators
Answer: COPmax = 5.316
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.