Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 3 m/s² along a runway. Find its speed v after 2000 m.
v₀ = 0a = 3 m/s²s = 2000 m
v = m/s
2.KinematicsHard
A ball is thrown straight up at 5 m/s from the edge of a roof 35 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 5 m/sh₀ = 35 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 2 kg block slides down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 2 kgθ = 45°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 7.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 1.5 kg mass. The coefficient of kinetic friction between block and table is 0.1. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 7.5 kgm2 = 1.5 kgμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 30° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 38 m/sθ = 30°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 30° above horizontal from the top of a 10 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 34 m/sθ = 30°h = 10 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A block slides from rest down a slope at 45° to the horizontal. The coefficient of kinetic friction is 0.4. Find its speed v after it has slid 6 m along the slope.
θ = 45°μ = 0.4d = 6 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 2 kg block is released from rest at height 4.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4 m long (μ = 0.25) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 2 kgh = 4.5 mL = 4 mμ = 0.25k = 2000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 15 g bullet is fired horizontally into a 4 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 18 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 15 gM = 4 kgh = 18 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.3 kg ball hits a wall at 10 m/s and bounces straight back at 20 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.3 kgvin = 10 m/svout = 20 m/sΔt = 20 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 75 mm to 50 mm. In the wide section the pressure is 290 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A hose with an inner diameter of 32 mm siphons water from an open tank. The highest point C of the hose is 2.5 m above the water surface, and the outlet (open to the air) is 2.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 32 mmzC = +2.5 mz2 = −2.5 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
What volume V does 400 g of CO₂ occupy at 500 kPa and 85 °C? Treat it as an ideal gas.
A heat engine works between a hot reservoir at 725 °C and a cold reservoir at 40 °C. Find the highest possible thermal efficiency ηmax.
TH = 725 °CTL = 40 °C
ηmax = %
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1200 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 25 °C. Both engines have the same thermal efficiency. Find Tm in °C.
TH = 1200 °CTL = 25 °C
Tm = °C
19.Waves, sound & opticsMedium
An object stands 30 cm in front of a thin diverging lens with a focal length of 25 cm. Find the magnification m (negative for an inverted image).
do = 30 cmf = −25 cm
m =
20.Waves, sound & opticsHard
Light of wavelength 532 nm falls on two slits 0.25 mm apart. The screen is 1.2 m away. Find the distance y4 from the central bright fringe to bright fringe number 4.
λ = 532 nmd = 0.25 mmL = 1.2 mm = 4
y4 = mm
3Solutions
1.Kinematics
Answer: v = 109.5 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·3·2000) = 109.5 m/s
Answer
v = 109.5 m/s
(394.4 km/h)
2.Kinematics
Answer: t = 3.229 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−35 = 5·t − ½·9.81·t²
4.905·t² − 5·t − 35 = 0
Solve the quadratic
Only the positive root is physical.
t = (5 + √(5² + 2·9.81·35))/9.81 = 3.229 s
Answer
t = 3.229 s
3.Newton’s laws
Answer: a = 4.856 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 38·cos 30° = 32.91 m/s
vy = v0·sin θ = 38·sin 30° = 19 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·19/9.81 = 3.874 s
Answer
t = 3.874 s
6.Projectile motion
Answer: x = 117.1 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 34·cos 30° = 29.44 m/s
vy = v0·sin θ = 34·sin 30° = 17 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 10 + 17·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (17 + √(289 + 196.2))/9.81 = 3.978 s
Horizontal distance
x = vx·t = 29.44·3.978 = 117.1 m
Answer
x = 117.1 m
7.Work & energy
Answer: v = 7.067 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·6·(0.7071 − 0.4·0.7071)) = 7.067 m/s
Answer
v = 7.067 m/s
8.Work & energy
Answer: v = 8.287 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(4.5 − 0.25·4) = 68.67 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·3.5) = 8.287 m/s
Answer
v = 8.287 m/s
9.Momentum & collisions
Answer: v = 503 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.18) = 1.879 m/s
Collision
m·v = (m + M)·V → v = (0.015 + 4)·1.879/0.015 = 503 m/s
Answer
v = 503 m/s
10.Momentum & collisions
Answer: J = 9 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.3·(20 + 10) = 9 N·s
Answer
J = 9 N·s
11.Hydrostatic force
Answer: F = 235.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 3/2 = 4 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4·6 = 235.4 kN
Answer
F = 235.4 kN
12.Hydrostatic force
Answer: F = 50.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 1.5/2 = 2.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2.25·2.25 = 50.9 kN
Answer
F = 50.9 kN
13.Continuity & Bernoulli
Answer: p2 = 283.8 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 453.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(400/150)·(453.1/283.1) = 42.68 L
Answer
V2 = 42.68 L
17.Heat engines & refrigerators
Answer: ηmax = 68.63 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 725 + 273.15 = 998.1 K
TL = 40 + 273.15 = 313.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 313.1/998.1 = 68.63 %
Answer
ηmax = 68.63 %
18.Heat engines & refrigerators
Answer: Tm = 389.6 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1200 + 273.15 = 1473 K
TL = 25 + 273.15 = 298.1 K
Equal efficiencies
1 − Tm/TH = 1 − TL/Tm gives Tm² = TH·TL.
Tm = √(1473·298.1) = 662.7 K = 389.6 °C
Answer
Tm = 389.6 °C
19.Waves, sound & optics
Answer: m = 0.4545
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−25) − 1/30
di = −13.64 cm
Magnification
m = −di/do = −(−13.64)/30 = 0.4545
Answer
m = 0.4545
20.Waves, sound & optics
Answer: y4 = 10.21 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …