Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 60 km/h brakes with a constant deceleration of 3 m/s² until it stops. How long does braking take? Find t.
v₀ = 60 km/ha = −3 m/s²v = 0
t = s
2.KinematicsHard
A tram starts from rest and accelerates at 3 m/s² for 8 s, then runs at constant speed for 23 s, and finally brakes at 5 m/s² until it stops. Find the total travel time t.
a1 = 3 m/s²t1 = 8 st2 = 23 sa3 = −5 m/s²
t = s
3.Newton’s lawsMedium
A 16 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 16 kgθ = 40°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 6 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4.5 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 6 kgm2 = 4.5 kgμ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 32 m/sθ = 70°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 20° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 29 m/sθ = 20°h = 45 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 1200 kg car drives up a 5° slope at a constant 72 km/h. Air resistance and rolling resistance together amount to 700 N. Find the power P the wheels must deliver, in kW.
A 4 kg block is released from rest at height 3.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3.5 m long (μ = 0.3) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 4 kgh = 3.5 mL = 3.5 mμ = 0.3k = 2500 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 1700 kg car moving at 18 m/s runs into a stationary 1700 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 1700 kgv1 = 18 m/sm2 = 1700 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
A 12 g bullet is fired horizontally into a 2 kg block hanging from light strings 1.3 m long, and stays in it. The strings swing out to a largest angle of 25° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 2 kgL = 1.3 mθ = 25°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of seawater, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal venturi meter with an inlet diameter of 100 mm and a throat diameter of 60 mm. The pressure at the inlet is 55 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 10 m. At section 1 the pressure is 250 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 425 °C and a cold reservoir at 5 °C. Find the highest possible thermal efficiency ηmax.
TH = 425 °CTL = 5 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is -5 °C outside, delivering 15 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 21 °CTL = -5 °CQ̇H = 15 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A pipe closed at one end must have its harmonic number 3 at 515 Hz. The speed of sound is 343 m/s. Find the length L of the pipe.
v = 343 m/sn = 3f3 = 515 Hz
L = m
20.Waves, sound & opticsHard
An object is 10 cm in front of a concave mirror with a radius of curvature of 60 cm. Find the magnification m (negative for an inverted image).
do = 10 cmR = 60 cm
m =
3Solutions
1.Kinematics
Answer: t = 5.556 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 60/3.6 = 16.67 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 16.67/3 = 5.556 s
Answer
t = 5.556 s
2.Kinematics
Answer: t = 35.8 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 3·8 = 24 m/s
Braking time
t3 = v/a3 = 24/5 = 4.8 s
Total time
t = 8 + 23 + 4.8 = 35.8 s
Answer
t = 35.8 s
3.Newton’s laws
Answer: a = 4.051 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 32·cos 70° = 10.94 m/s
vy = v0·sin θ = 32·sin 70° = 30.07 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·30.07/9.81 = 6.131 s
Answer
t = 6.131 s
6.Projectile motion
Answer: t = 4.204 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 29·cos 20° = 27.25 m/s
vy = v0·sin θ = 29·sin 20° = 9.919 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 45 + 9.919·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (9.919 + √(98.38 + 882.9))/9.81 = 4.204 s
Answer
t = 4.204 s
7.Work & energy
Answer: P = 34.52 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 1200·9.81 = 11772 N
mg·sin θ = 11772·sin 5° = 1026 N
F = 1026 + 700 = 1726 N
Power
v = 72/3.6 = 20 m/s
P = F·v = 1726·20 = 34520 W = 34.52 kW
Answer
P = 34.52 kW
8.Work & energy
Answer: v = 6.933 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(3.5 − 0.3·3.5) = 96.14 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·2.45) = 6.933 m/s
Answer
v = 6.933 m/s
9.Momentum & collisions
Answer: ΔK/K = 50 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1700·18/3400 = 9 m/s
Kinetic energy before and after
Kbefore = ½·1700·18² = 275400 J
Kafter = ½·3400·9² = 137700 J
Fraction lost
ΔK/K = 137700/275400 = 50 %
Answer
ΔK/K = 50 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v = 259.2 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.3·(1 − cos 25°) = 0.1218 m
Speed after impact
V = √(2·9.81·0.1218) = 1.546 m/s
Collision
v = (m + M)·V/m = 2.012·1.546/0.012 = 259.2 m/s
Answer
v = 259.2 m/s
11.Hydrostatic force
Answer: F = 117.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 3/2 = 2 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2·6 = 117.7 kN
Answer
F = 117.7 kN
12.Hydrostatic force
Answer: ycp = 4.789 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1.5/2 = 4.75 m
A = H·b = 1.5·2 = 3 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·4.75·3 = 143.3 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(60/100)² = 0.36·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 425 + 273.15 = 698.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/698.1 = 60.16 %
Answer
ηmax = 60.16 %
18.Heat engines & refrigerators
Answer: Ẇmin = 1.326 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 15/11.31 = 1.326 kW
Answer
Ẇmin = 1.326 kW
19.Waves, sound & optics
Answer: L = 0.4995 m
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength
λ = v/f = 343/515 = 0.666 m
Length
L = nλ/4 = 3·0.666/4 = 0.4995 m
Answer
L = 0.4995 m
20.Waves, sound & optics
Answer: m = 1.5
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.