Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 72 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. Find the braking distance s.
v₀ = 72 km/ha = −4.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 11 m/s from the edge of a roof 15 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 11 m/sh₀ = 15 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 6 kg block slides down a frictionless slope at 20° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 6 kgθ = 20°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 30° with a speed of 7.5 m/s. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 7.5 m/sθ = 30°μ = 0.3g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 65° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 34 m/sθ = 65°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 29 m/s and 40° above the horizontal from the top of a 50 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 29 m/sθ = 40°h = 50 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A car travelling at 80 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.7. Find the stopping distance d.
v = 80 km/hμ = 0.7g = 9.81 m/s²
d = m
8.Work & energyHard
An 8 kg block starts from rest at the bottom of a 20° slope and is pulled up the slope by a constant force of 55 N parallel to the slope. The coefficient of kinetic friction is 0.15. Find the speed v of the block after it has moved 4 m up the slope.
A 3.5 kg glider moving at 5 m/s makes a perfectly elastic head-on collision with a 1.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3.5 kgm2 = 1.5 kgv1 = 5 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.2 kg ball hits a wall at 26 m/s and bounces straight back at 4 m/s. The contact lasts 40 ms. Find the average force Favg of the wall on the ball.
m = 0.2 kgvin = 26 m/svout = 4 m/sΔt = 40 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 150 mm to 75 mm. In the wide section the pressure is 130 kPa and the velocity is 2.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A closed water tank has compressed air above the water at a gauge pressure of 190 kPa. Water leaves through an opening with a diameter of 50 mm, 2.5 m below the water surface, into the open air. Ignoring losses, find the jet velocity v. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 775 °C and a cold reservoir at 30 °C. It takes in 2600 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 775 °CTL = 30 °CQH = 2600 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump delivers 13.5 kW of heat to a heating system at 22 °C, taking heat from a source at 5 °C. Its actual COP is 30% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 22 °CTL = 5 °CηII = 30%Q̇H = 13.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A small source sends sound equally in all directions. The level is 60 dB at 1 m from it. Find the level β2 at 10 m, ignoring absorption and reflections.
β1 = 60 dBr1 = 1 mr2 = 10 m
β2 = dB
20.Waves, sound & opticsHard
An optical fibre has a core with n₁ = 1.48 and a cladding with n₂ = 1.47. Find its numerical aperture NA.
n1 = 1.48n2 = 1.47
NA =
3Solutions
1.Kinematics
Answer: s = 44.44 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 72/3.6 = 20 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 20²/(2·4.5) = 44.44 m
Answer
s = 44.44 m
2.Kinematics
Answer: t = 3.199 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−15 = 11·t − ½·9.81·t²
4.905·t² − 11·t − 15 = 0
Solve the quadratic
Only the positive root is physical.
t = (11 + √(11² + 2·9.81·15))/9.81 = 3.199 s
Answer
t = 3.199 s
3.Newton’s laws
Answer: a = 3.355 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 30° + 0.3·cos 30°) = 7.454 m/s²
Distance
d = v₀²/(2a) = 7.5²/(2·7.454) = 3.773 m
Answer
d = 3.773 m
5.Projectile motion
Answer: H = 48.4 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 34·cos 65° = 14.37 m/s
vy = v0·sin θ = 34·sin 65° = 30.81 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 30.81²/(2·9.81) = 48.4 m
Answer
H = 48.4 m
6.Projectile motion
Answer: α = 58.64 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 29·cos 40° = 22.22 m/s
vy0 = 29·sin 40° = 18.64 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(18.64² + 2·9.81·50) = 36.45 m/s
Impact angle
tan α = vy/vx = 36.45/22.22 → α = 58.64°
Answer
α = 58.64°
7.Work & energy
Answer: d = 35.96 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 80/3.6 = 22.22 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 22.22²/(2·0.7·9.81) = 35.96 m
Answer
d = 35.96 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 4.135 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 8·9.81 = 78.48 N
mg·sin θ = 26.84 N
μ·mg·cos θ = 11.06 N
Work–energy
½mv² = (55 − 37.9)·4 = 68.38 J
v = √(2·68.38/8) = 4.135 m/s
Answer
v = 4.135 m/s
9.Momentum & collisions
Answer: v′2 = 7 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3.5 − 1.5)/(3.5 + 1.5)·5 = 2 m/s
v′2 = 2·3.5/(3.5 + 1.5)·5 = 7 m/s
Answer
v′2 = 7 m/s
10.Momentum & collisions
Answer: Favg = 150 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.2·(4 + 26) = 6 N·s
Average force
Favg = J/Δt = 6/0.04 = 150 N
Answer
Favg = 150 N
11.Hydrostatic force
Answer: F = 128.8 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2.5/2 = 1.75 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·7.5 = 128.8 kN
Answer
F = 128.8 kN
12.Hydrostatic force
Answer: ycp = 1.4 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 1.5/2 = 1.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·1.25·2.25 = 28.28 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli from the surface to the jet
v = √(2·(190000/1000 + 9.81·2.5)) = 20.71 m/s
Answer
v = 20.71 m/s
15.Ideal gas law
Answer: P = 787.6 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 50/32 = 1.563 mol
T = 30 + 273.15 = 303.1 K
Pressure
P = nRT/V = 1.563·8.314·303.1/0.005 = 787.6 kPa
Answer
P = 787.6 kPa
16.Ideal gas law
Answer: ρ = 3.916 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 200 + 273.15 = 473.1 K
Density
ρ = 550·28.01/(8.314·473.1) = 3.916 kg/m³
Answer
ρ = 3.916 kg/m³
17.Heat engines & refrigerators
Answer: Wmax = 1848 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 775 + 273.15 = 1048 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/1048 = 71.08 %
Maximum work
Wmax = ηmax·QH = 0.7108·2600 = 1848 kJ
Answer
Wmax = 1848 kJ
18.Heat engines & refrigerators
Answer: Ẇ = 2.592 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 22 + 273.15 = 295.1 K
TL = 5 + 273.15 = 278.1 K
Carnot and actual COP
COPmax = 295.1/(295.1 − 278.1) = 17.36
COP = 0.3·17.36 = 5.209
Power input
Ẇ = Q̇H/COP = 13.5/5.209 = 2.592 kW
Answer
Ẇ = 2.592 kW
19.Waves, sound & optics
Answer: β2 = 40 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Intensity ratio
I₂/I₁ = (1/10)² = 0.01
New level
β₂ = 60 + 10·log₁₀(0.01) = 40 dB
Answer
β2 = 40 dB
Every doubling of the distance lowers the level by about 6 dB.
20.Waves, sound & optics
Answer: NA = 0.1718
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.