Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 80 km/h sees an obstacle. Her reaction time is 0.6 s, after which the car brakes with a constant deceleration of 7 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 80 km/htr = 0.6 sa = −7 m/s²
d = m
2.KinematicsHard
A tram starts from rest and accelerates at 2 m/s² for 10 s, then runs at constant speed for 12 s, and finally brakes at 3.5 m/s² until it stops. Find the total travel time t.
a1 = 2 m/s²t1 = 10 st2 = 12 sa3 = −3.5 m/s²
t = s
3.Newton’s lawsMedium
A 5 kg block slides down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 5 kgθ = 25°μ = 0.25g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 2 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 2 kgm2 = 4.5 kgμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 30° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 14 m/sθ = 30°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 13 m/s and 45° above the horizontal from the top of a 10 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 13 m/sθ = 45°h = 10 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 0.2 kg ball hangs on a light string of length 0.8 m. It is pulled aside until the string makes 40° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 0.2 kgL = 0.8 mθ = 40°g = 9.81 m/s²
T = N
8.Work & energyHard
A 10 kg cart is released from rest at a height of 4.8 m on a smooth track that leads into a vertical circular loop of radius 1.5 m. Find the speed v of the cart at the top of the loop.
m = 10 kgh = 4.8 mR = 1.5 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 20 g bullet is fired horizontally into a 4 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 23 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 20 gM = 4 kgh = 23 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 0.3 kg ball hits a wall at 23 m/s and bounces straight back at 8 m/s. The contact lasts 5 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.3 kgvin = 23 m/svout = 8 m/sΔt = 5 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 1 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 50 mm. The water level is kept 4.5 m above the orifice and the discharge coefficient is 0.62. Find the flow rate Q. Use g = 9.81 m/s².
d = 50 mmh = 4.5 mCd = 0.62g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 100 mm to 40 mm while rising 3 m. At section 1 the pressure is 250 kPa and the velocity is 0.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 700 °C and rejects heat to the surroundings at 25 °C. Its actual thermal efficiency is 28%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 700 °CTL = 25 °Cη = 28%
ηII = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 5 °C in a kitchen at 25 °C, removing heat from the cold space at 4 kW. Find the minimum power input Ẇmin.
TH = 25 °CTL = 5 °CQ̇L = 4 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object 1.5 cm tall stands 40 cm in front of a thin converging lens with a focal length of 12 cm. Find the image height hi (negative for an inverted image).
ho = 1.5 cmdo = 40 cmf = 12 cm
hi = cm
20.Waves, sound & opticsHard
Light of wavelength 550 nm passes through a single slit 0.05 mm wide. Find the width w of the central bright maximum on a screen 3 m away (between the first dark fringes on either side).
λ = 550 nma = 0.05 mmL = 3 m
w = mm
3Solutions
1.Kinematics
Answer: d = 48.61 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 80/3.6 = 22.22 m/s
Reaction distance
d1 = v₀·tr = 22.22·0.6 = 13.33 m
Braking distance
d2 = v₀²/(2a) = 22.22²/(2·7) = 35.27 m
Total
d = 13.33 + 35.27 = 48.61 m
Answer
d = 48.61 m
2.Kinematics
Answer: t = 27.71 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 2·10 = 20 m/s
Braking time
t3 = v/a3 = 20/3.5 = 5.714 s
Total time
t = 10 + 12 + 5.714 = 27.71 s
Answer
t = 27.71 s
3.Newton’s laws
Answer: a = 1.923 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 30° = 12.12 m/s
vy = v0·sin θ = 14·sin 30° = 7 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·7/9.81 = 1.427 s
Horizontal distance
x = vx·t = 12.12·1.427 = 17.3 m
Answer
x = 17.3 m
6.Projectile motion
Answer: H = 14.31 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 13·sin 45° = 9.192 m/s
Rise above the cliff
Δh = vy²/(2g) = 9.192²/(2·9.81) = 4.307 m
Height above the ground
H = 10 + 4.307 = 14.31 m
Answer
H = 14.31 m
7.Work & energy
Answer: T = 2.88 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·0.8·(1 − cos 40°) = 3.672 m²/s²
Forces at the bottom
m·g = 0.2·9.81 = 1.962 N
T = mg + mv²/L = 1.962 + 0.2·3.672/0.8 = 2.88 N
Answer
T = 2.88 N
Check: T = mg(3 − 2cos θ) = 2.88 N.
8.Work & energy
Answer: v = 5.943 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(4.8 − 3) = 35.32 m²/s²
v = 5.943 m/s
Answer
v = 5.943 m/s
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v = 427 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.23) = 2.124 m/s
Collision
m·v = (m + M)·V → v = (0.02 + 4)·2.124/0.02 = 427 m/s
Answer
v = 427 m/s
10.Momentum & collisions
Answer: J = 9.3 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.3·(8 + 23) = 9.3 N·s
Answer
J = 9.3 N·s
11.Hydrostatic force
Answer: F = 44.15 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1/2 = 4.5 m
A = H·b = 1·1 = 1 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.5·1 = 44.15 kN
Answer
F = 44.15 kN
12.Hydrostatic force
Answer: F = 36.79 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1/2 = 2.5 m
A = H·b = 1·1.5 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·1.5 = 36.79 kN
Answer
F = 36.79 kN
13.Continuity & Bernoulli
Answer: Q = 11.44 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·4.5) = 9.396 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 700 + 273.15 = 973.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηCarnot = 1 − 298.1/973.1 = 69.36 %
Second-law efficiency
ηII = η/ηCarnot = 28/69.36 = 40.37 %
Answer
ηII = 40.37 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.2876 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 4/13.91 = 0.2876 kW
Answer
Ẇmin = 0.2876 kW
19.Waves, sound & optics
Answer: hi = −0.6429 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/12 − 1/40
di = 17.14 cm
Magnification and height
m = −17.14/40 = −0.4286
hi = −0.4286·1.5 = −0.6429 cm
Answer
hi = −0.6429 cm
20.Waves, sound & optics
Answer: w = 66 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …