Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 5.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 100 km/ha = −5.5 m/s²v = 0
t = s
2.KinematicsHard
Ball A is dropped from rest from a height of 40 m. At the same instant ball B is thrown straight up from the ground directly below at 24 m/s. Ignore air resistance and use g = 9.81 m/s². At what height y above the ground do they meet?
H = 40 mv0B = 24 m/sg = 9.81 m/s²
y = m
3.Newton’s lawsMedium
A 13 kg block slides down a slope at 35° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 13 kgθ = 35°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 6.5 kg block on a ramp at 35° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 8.5 kg mass. The hanging mass moves down. The ramp is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 6.5 kgm2 = 8.5 kgθ = 35°μ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 30 m/sθ = 20°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 60° above horizontal from the top of a 20 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 35 m/sθ = 60°h = 20 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 10 kg ball hangs on a light string of length 1.5 m. It is pulled aside until the string makes 50° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 10 kgL = 1.5 mθ = 50°g = 9.81 m/s²
T = N
8.Work & energyHard
A 0.5 kg block is released from rest at height 3.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2 m long (μ = 0.25) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 0.5 kgh = 3.5 mL = 2 mμ = 0.25k = 2500 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 3.5 kg glider moving at 10 m/s makes a perfectly elastic head-on collision with a 4.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3.5 kgm2 = 4.5 kgv1 = 10 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 12 g bullet is fired horizontally into a 4.5 kg block hanging from light strings 1.9 m long, and stays in it. The strings swing out to a largest angle of 15° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 4.5 kgL = 1.9 mθ = 15°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 150 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 7 m. At section 1 the pressure is 360 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at -5 °C by removing 5.5 kW of heat, and rejects heat to the surroundings at 30 °C. Find the rate Q̇H at which it rejects heat.
TL = -5 °CTH = 30 °CQ̇L = 5.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 21 °C while it is 0 °C outside, delivering 4 kW of heat to the house. Find the minimum power input Ẇmin.
TH = 21 °CTL = 0 °CQ̇H = 4 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 50 cm in front of a thin converging lens with a focal length of 20 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 50 cmf = 20 cm
di = cm
20.Waves, sound & opticsHard
Two thin lenses share an axis, 20 cm apart: lens 1 with f₁ = 20 cm and lens 2 with f₂ = 8 cm. An object stands 12 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 20 cmf2 = 8 cms = 20 cmdo = 12 cm
di2 = cm
3Solutions
1.Kinematics
Answer: t = 5.051 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 27.78/5.5 = 5.051 s
Answer
t = 5.051 s
2.Kinematics
Answer: y = 26.38 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
40 − ½g·t² = 24·t − ½g·t² → t = 40/24 = 1.667 s
Meeting height
y = 24·1.667 − ½·9.81·1.667² = 26.38 m
Answer
y = 26.38 m
3.Newton’s laws
Answer: a = 3.216 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 83.39 N
m₁·g·sin θ = 36.57 N
μ·m₁·g·cos θ = 0 N
Acceleration of the system
a = (83.39 − 36.57 − 0)/15 = 3.121 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 8.5·(9.81 − 3.121) = 56.86 N
Answer
T = 56.86 N
5.Projectile motion
Answer: H = 5.366 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 30·cos 20° = 28.19 m/s
vy = v0·sin θ = 30·sin 20° = 10.26 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 10.26²/(2·9.81) = 5.366 m
Answer
H = 5.366 m
6.Projectile motion
Answer: t = 6.781 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 35·cos 60° = 17.5 m/s
vy = v0·sin θ = 35·sin 60° = 30.31 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 20 + 30.31·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (30.31 + √(918.7 + 392.4))/9.81 = 6.781 s
Answer
t = 6.781 s
7.Work & energy
Answer: T = 168.2 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·1.5·(1 − cos 50°) = 10.51 m²/s²
Forces at the bottom
m·g = 10·9.81 = 98.1 N
T = mg + mv²/L = 98.1 + 10·10.51/1.5 = 168.2 N
Answer
T = 168.2 N
Check: T = mg(3 − 2cos θ) = 168.2 N.
8.Work & energy
Answer: v = 7.672 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 4.905·(3.5 − 0.25·2) = 14.71 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·3) = 7.672 m/s
Answer
v = 7.672 m/s
9.Momentum & collisions
Answer: v′2 = 8.75 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3.5 − 4.5)/(3.5 + 4.5)·10 = −1.25 m/s
v′2 = 2·3.5/(3.5 + 4.5)·10 = 8.75 m/s
Answer
v′2 = 8.75 m/s
10.Momentum & collisions
Answer: v = 423.8 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.9·(1 − cos 15°) = 0.06474 m
Speed after impact
V = √(2·9.81·0.06474) = 1.127 m/s
Collision
v = (m + M)·V/m = 4.512·1.127/0.012 = 423.8 m/s
Answer
v = 423.8 m/s
11.Hydrostatic force
Answer: F = 239.1 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2.5/2 = 3.25 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·7.5 = 239.1 kN
Answer
F = 239.1 kN
12.Hydrostatic force
Answer: ycp = 5.349 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·2 = 5 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·5.25·5 = 324.5 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 473.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 2·(250/450)·(473.1/283.1) = 1.857 L
Answer
V2 = 1.857 L
17.Heat engines & refrigerators
Answer: Q̇H = 6.218 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 30 + 273.15 = 303.1 K
TL = -5 + 273.15 = 268.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 5.5·303.1/268.1 = 6.218 kW
Answer
Q̇H = 6.218 kW
Power input: Ẇ = 0.7179 kW.
18.Heat engines & refrigerators
Answer: Ẇmin = 0.2856 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇H/COP = 4/14.01 = 0.2856 kW
Answer
Ẇmin = 0.2856 kW
19.Waves, sound & optics
Answer: di = 33.33 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/20 − 1/50
di = 33.33 cm
Ray diagram
real, on the far side of the lens
Answer
di = 33.33 cm
20.Waves, sound & optics
Answer: di2 = 9.524 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.