Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 108 km/h sees an obstacle. Her reaction time is 1.4 s, after which the car brakes with a constant deceleration of 4 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 108 km/htr = 1.4 sa = −4 m/s²
d = m
2.KinematicsHard
A ball is thrown straight up at 11 m/s from the edge of a roof 30 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 11 m/sh₀ = 30 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 25 kg sled is pulled across level snow by a rope at 35° above the horizontal with a force of 190 N. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 25 kgF = 190 Nθ = 35°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 2 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 3.5 kg mass. The coefficient of kinetic friction between block and table is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 2 kgm2 = 3.5 kgμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 50° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 28 m/sθ = 50°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 60 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 33 m/sθ = 45°h = 60 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A block slides from rest down a slope at 25° to the horizontal. The coefficient of kinetic friction is 0.35. Find its speed v after it has slid 10 m along the slope.
θ = 25°μ = 0.35d = 10 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A spring of stiffness 2000 N/m at the bottom of a 30° slope is compressed by 10 cm against a 0.5 kg block and released. The coefficient of kinetic friction between block and slope is 0.2. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
A 1600 kg car moving at 20 m/s runs into a stationary 1400 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1600 kgv1 = 20 m/sm2 = 1400 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 1000 kg car runs into a parked 1100 kg car. The wrecks lock together and skid 14.5 m before stopping. The coefficient of kinetic friction between tyres and road is 0.8. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 3 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 3 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 75 mm to 25 mm. In the wide section the pressure is 250 kPa and the velocity is 1 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A horizontal venturi meter (inlet 200 mm, throat 100 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 300 mm. The discharge coefficient is 0.99. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A reversible (Carnot) heat engine takes in 4600 kJ of heat from a reservoir at 725 °C and rejects 1535 kJ per cycle. Find the temperature TL of the cold reservoir in °C.
TH = 725 °CQH = 4600 kJQL = 1535 kJ
TL = °C
18.Heat engines & refrigeratorsHard
A heat pump delivers 17 kW of heat to a heating system at 55 °C, taking heat from a source at -10 °C. Its actual COP is 35% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 55 °CTL = -10 °CηII = 35%Q̇H = 17 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A string fixed at both ends is 0.5 m long; waves travel on it at 120 m/s. Find the frequency f3 of its harmonic number 3.
v = 120 m/sn = 3L = 0.5 m
f3 = Hz
20.Waves, sound & opticsHard
Two thin lenses share an axis, 10 cm apart: lens 1 with f₁ = 10 cm and lens 2 with f₂ = 10 cm. An object stands 15 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 10 cmf2 = 10 cms = 10 cmdo = 15 cm
di2 = cm
3Solutions
1.Kinematics
Answer: d = 154.5 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Reaction distance
d1 = v₀·tr = 30·1.4 = 42 m
Braking distance
d2 = v₀²/(2a) = 30²/(2·4) = 112.5 m
Total
d = 42 + 112.5 = 154.5 m
Answer
d = 154.5 m
2.Kinematics
Answer: t = 3.837 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−30 = 11·t − ½·9.81·t²
4.905·t² − 11·t − 30 = 0
Solve the quadratic
Only the positive root is physical.
t = (11 + √(11² + 2·9.81·30))/9.81 = 3.837 s
Answer
t = 3.837 s
3.Newton’s laws
Answer: a = 5.135 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 245.3 − 190·sin 35° = 136.3 N
Horizontal forces
m·a = F·cos θ − μ·N = 155.6 − 27.25
a = 128.4/25 = 5.135 m/s²
Answer
a = 5.135 m/s²
4.Newton’s laws
Answer: a = 5.529 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 28·cos 50° = 18 m/s
vy = v0·sin θ = 28·sin 50° = 21.45 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·21.45/9.81 = 4.373 s
Answer
t = 4.373 s
6.Projectile motion
Answer: t = 6.608 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 33·cos 45° = 23.33 m/s
vy = v0·sin θ = 33·sin 45° = 23.33 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 60 + 23.33·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (23.33 + √(544.5 + 1177))/9.81 = 6.608 s
Answer
t = 6.608 s
7.Work & energy
Answer: v = 4.548 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·10·(0.4226 − 0.35·0.9063)) = 4.548 m/s
Answer
v = 4.548 m/s
8.Work & energy
Answer: d = 3.028 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 10 cm = 0.1 m
½kx² = ½·2000·0.1² = 10 J
Energy balance along the slope
m·g = 0.5·9.81 = 4.905 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 10/(4.905·(0.5 + 0.2·0.866)) = 3.028 m
Answer
d = 3.028 m
9.Momentum & collisions
Answer: ΔK = 149333 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1600·20/3000 = 10.67 m/s
Kinetic energy before and after
Kbefore = ½·1600·20² = 320000 J
Kafter = ½·3000·10.67² = 170667 J
Energy lost
ΔK = 320000 − 170667 = 149333 J
Answer
ΔK = 149333 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v1 = 31.68 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 3/2 = 5.5 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.5·9 = 485.6 kN
Answer
F = 485.6 kN
12.Hydrostatic force
Answer: F = 73.58 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 3/2 = 2.5 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·3 = 73.58 kN
Answer
F = 73.58 kN
13.Continuity & Bernoulli
Answer: p2 = 210 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli
Work in Pa, then divide by 1000 to get kPa.
v2 = v1·(d1/d2)² = 1·(75/25)² = 9 m/s
½ρ(v1² − v2²) = ½·1000·(1² − 9²)/1000 = −40 kPa
p2 = p1 + ½ρ(v1² − v2²) = 250 + (−40) = 210 kPa
Answer
p2 = 210 kPa
14.Continuity & Bernoulli
Answer: Q = 69.16 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.3 = 37082 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperature of the source
TH = 725 + 273.15 = 998.1 K
Reversible heat ratio
TL = TH·QL/QH = 998.1·1535/4600 = 333.1 K = 59.93 °C
Answer
TL = 59.93 °C
18.Heat engines & refrigerators
Answer: Ẇ = 9.621 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 55 + 273.15 = 328.1 K
TL = -10 + 273.15 = 263.1 K
Carnot and actual COP
COPmax = 328.1/(328.1 − 263.1) = 5.048
COP = 0.35·5.048 = 1.767
Power input
Ẇ = Q̇H/COP = 17/1.767 = 9.621 kW
Answer
Ẇ = 9.621 kW
19.Waves, sound & optics
Answer: f3 = 360 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.5/3 = 0.3333 m
Frequency
f = v/λ = 120/0.3333 = 360 Hz
Answer
f3 = 360 Hz
20.Waves, sound & optics
Answer: di2 = 6.667 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.