Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 72 km/h brakes with a constant deceleration of 3.5 m/s² until it stops. Find the braking distance s.
v₀ = 72 km/ha = −3.5 m/s²v = 0
s = m
2.KinematicsHard
Ball A is dropped from rest from a height of 50 m. At the same instant ball B is thrown straight up from the ground directly below at 28 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 50 mv0B = 28 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 3.5 m/s and comes to rest after 6.2 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 3.5 m/sd = 6.2 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 4.5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 4 kg mass. The coefficient of kinetic friction between block and table is 0.25. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 4.5 kgm2 = 4 kgμ = 0.25g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 40° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 24 m/sθ = 40°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is thrown from ground level at 24 m/s and 35° above the horizontal. It lands on the flat roof of a building 3 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 24 m/sθ = 35°hroof = 3 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A toy launcher has a vertical spring of stiffness 2000 N/m. A 0.05 kg ball is placed on it and the spring is compressed by 2 cm, then released. Ignoring air resistance and the spring’s mass, find the height h the ball rises, measured from its position when the spring was compressed.
m = 0.05 kgk = 2000 N/mx = 2 cmg = 9.81 m/s²
h = m
8.Work & energyHard
A 1 kg cart is released from rest at a height of 8.8 m on a smooth track that leads into a vertical circular loop of radius 2.5 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 1 kgh = 8.8 mR = 2.5 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 14 kg projectile moving horizontally at 40 m/s explodes into two fragments that move along the same line. The 4 kg fragment continues forwards at 49 m/s. Find the velocity v′2 of the 10 kg fragment (positive in the original direction).
M = 14 kgu = 40 m/sm1 = 4 kgv′1 = 49 m/sm2 = 10 kg
v′2 = m/s
10.Momentum & collisionsHard
A 12 g bullet is fired horizontally into a 1.5 kg block hanging from light strings 1.9 m long, and stays in it. The strings swing out to a largest angle of 20° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 12 gM = 1.5 kgL = 1.9 mθ = 20°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 2 mH = 3 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 2.5 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows at 38 L/s through a horizontal pipe that narrows from 100 mm to 75 mm. The pressure in the narrow section is 220 kPa. Ignoring losses, find the pressure p1 in the wide section.
Water flows up through a pipe that narrows from 200 mm to 100 mm while rising 10 m. At section 1 the pressure is 160 kPa and the velocity is 2.5 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 400 °C and rejects heat to the surroundings at 40 °C. Its actual thermal efficiency is 40%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 400 °CTL = 40 °Cη = 40%
ηII = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 2 °C in a kitchen at 35 °C, removing heat from the cold space at 3 kW. Find the minimum power input Ẇmin.
TH = 35 °CTL = 2 °CQ̇L = 3 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A string fixed at both ends is 0.5 m long; waves travel on it at 150 m/s. Find the frequency f5 of its harmonic number 5.
v = 150 m/sn = 5L = 0.5 m
f5 = Hz
20.Waves, sound & opticsHard
A diffraction grating has 600 lines per millimetre. Light of wavelength 600 nm falls on it at right angles. What is the highest order mmax of bright maximum that can be seen?
N = 600 mm⁻¹λ = 600 nm
mmax =
3Solutions
1.Kinematics
Answer: s = 57.14 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 72/3.6 = 20 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 20²/(2·3.5) = 57.14 m
Answer
s = 57.14 m
2.Kinematics
Answer: t = 1.786 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
50 − ½g·t² = 28·t − ½g·t² → t = 50/28 = 1.786 s
Answer
t = 1.786 s
3.Newton’s laws
Answer: μ = 0.1007
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 3.5²/(2·6.2) = 0.9879 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 0.9879/9.81 = 0.1007
Answer
μ = 0.1007
4.Newton’s laws
Answer: a = 3.318 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 40° = 18.39 m/s
vy = v0·sin θ = 24·sin 40° = 15.43 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·15.43/9.81 = 3.145 s
Answer
t = 3.145 s
6.Projectile motion
Answer: x = 50.49 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 19.66 m/s, vy = 13.77 m/s
Time to land on the roof
Larger root: the ball is descending.
3 = 13.77·t − 4.905·t²
t = (13.77 + √(13.77² − 2·9.81·3))/9.81 = 2.568 s
Horizontal distance
x = vx·t = 19.66·2.568 = 50.49 m
Answer
x = 50.49 m
7.Work & energy
Answer: h = 0.8155 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 2 cm = 0.02 m
½kx² = ½·2000·0.02² = 0.4 J
Height
m·g = 0.05·9.81 = 0.4905 N
h = ½kx²/(mg) = 0.4/0.4905 = 0.8155 m
Answer
h = 0.8155 m
8.Work & energy
Answer: N = 20.01 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(8.8 − 5) = 74.56 m²/s²
Forces at the top
m·g = 1·9.81 = 9.81 N
N = mv²/R − mg = 1·74.56/2.5 − 9.81 = 20.01 N
Answer
N = 20.01 N
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v′2 = 36.4 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 14·40 = 560 kg·m/s
Momentum after
560 = 4·49 + 10·v′2
v′2 = (560 − 196)/10 = 36.4 m/s
Answer
v′2 = 36.4 m/s
10.Momentum & collisions
Answer: v = 188.9 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.9·(1 − cos 20°) = 0.1146 m
Speed after impact
V = √(2·9.81·0.1146) = 1.499 m/s
Collision
v = (m + M)·V/m = 1.512·1.499/0.012 = 188.9 m/s
Answer
v = 188.9 m/s
11.Hydrostatic force
Answer: F = 309 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 3/2 = 3.5 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.5·9 = 309 kN
Answer
F = 309 kN
12.Hydrostatic force
Answer: ycp = 3.028 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1/2 = 3 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·3·2 = 74.16 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Ic = b·H³/12 = 2·1³/12 = 0.1667 m⁴
ycp = yc + Ic/(yc·A) = 3 + 0.1667/(3·2) = 3.028 m
Answer
ycp = 3.028 m
13.Continuity & Bernoulli
Answer: p1 = 245.3 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 298.1 K, T2 = 443.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 5·(250/300)·(443.1/298.1) = 6.193 L
Answer
V2 = 6.193 L
17.Heat engines & refrigerators
Answer: ηII = 74.79 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
TL = 40 + 273.15 = 313.1 K
Carnot efficiency
ηCarnot = 1 − 313.1/673.1 = 53.48 %
Second-law efficiency
ηII = η/ηCarnot = 40/53.48 = 74.79 %
Answer
ηII = 74.79 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.3598 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 3/8.338 = 0.3598 kW
Answer
Ẇmin = 0.3598 kW
19.Waves, sound & optics
Answer: f5 = 750 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.5/5 = 0.2 m
Frequency
f = v/λ = 150/0.2 = 750 Hz
Answer
f5 = 750 Hz
20.Waves, sound & optics
Answer: mmax = 2
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …