Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 180 km/h to take off and the usable runway is 1500 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 180 km/hs = 1500 m
a = m/s²
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 3.7 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 3.7 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 10 m/s and comes to rest after 20 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 10 m/sd = 20 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
A 2 kg block on a ramp at 20° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 8 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.2. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 2 kgm2 = 8 kgθ = 20°μ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 20° above the horizontal and lands 20 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 20°R = 20 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 21 m/s and 20° above the horizontal from the top of a 45 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 21 m/sθ = 20°h = 45 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A block slides from rest down a slope at 20° to the horizontal. The coefficient of kinetic friction is 0.15. Find its speed v after it has slid 18 m along the slope.
θ = 20°μ = 0.15d = 18 mg = 9.81 m/s²
v = m/s
8.Work & energyHard
A 5 kg block rests on a rough horizontal table (μ = 0.4). A light string runs from it over a smooth pulley at the edge of the table to a hanging 6 kg block. The system is released from rest. Find the speed v of the blocks after the hanging block has dropped 1 m.
m1 = 5 kgm2 = 6 kgμ = 0.4d = 1 mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 500 kg car moving at 25 m/s runs into a stationary 600 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 500 kgv1 = 25 m/sm2 = 600 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 28 m/s and bounces straight back at 15 m/s. The contact lasts 20 ms. Find the average force Favg of the wall on the ball.
m = 0.55 kgvin = 28 m/svout = 15 m/sΔt = 20 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 3 m wide sits in the wall of a tank of seawater, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 40 mm. The water level is kept 5.5 m above the orifice and the discharge coefficient is 0.65. Find the flow rate Q. Use g = 9.81 m/s².
d = 40 mmh = 5.5 mCd = 0.65g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A closed water tank has compressed air above the water at a gauge pressure of 110 kPa. Water leaves through an opening with a diameter of 40 mm, 3.5 m below the water surface, into the open air. Ignoring losses, find the jet velocity v. Use g = 9.81 m/s².
A heat engine works between a hot reservoir at 550 °C and a cold reservoir at 25 °C. It takes in 2100 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 550 °CTL = 25 °CQH = 2100 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1200 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 40 °C. Both engines produce the same work. Find Tm in °C.
TH = 1200 °CTL = 40 °C
Tm = °C
19.Waves, sound & opticsMedium
A small loudspeaker radiates 0.2 W of sound power equally in all directions. Find the sound intensity level β at 20 m.
P = 0.2 Wr = 20 mI0 = 10⁻¹² W/m²
β = dB
20.Waves, sound & opticsHard
Light of wavelength 656 nm falls at right angles on a grating with 500 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 500 mm⁻¹λ = 656 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: a = 0.8333 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 180/3.6 = 50 m/s
Acceleration
a = v²/(2s) = 50²/(2·1500) = 0.8333 m/s²
Answer
a = 0.8333 m/s²
2.Kinematics
Answer: d = 60.86 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(3.7 − t₁)
4.905·t₁² + 343·t₁ − 1269 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1269))/(2·4.905) = 3.523 s
Depth
d = ½·9.81·3.523² = 60.86 m
Answer
d = 60.86 m
3.Newton’s laws
Answer: μ = 0.2548
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 10²/(2·20) = 2.5 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 2.5/9.81 = 0.2548
Answer
μ = 0.2548
4.Newton’s laws
Answer: a = 6.808 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 78.48 N
m₁·g·sin θ = 6.71 N
μ·m₁·g·cos θ = 3.687 N
Acceleration of the system
a = (78.48 − 6.71 − 3.687)/10 = 6.808 m/s²
Answer
a = 6.808 m/s²
5.Projectile motion
Answer: v0 = 17.47 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·20/sin 40°) = 17.47 m/s
Answer
v0 = 17.47 m/s
6.Projectile motion
Answer: α = 57.16 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 21·cos 20° = 19.73 m/s
vy0 = 21·sin 20° = 7.182 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(7.182² + 2·9.81·45) = 30.57 m/s
Impact angle
tan α = vy/vx = 30.57/19.73 → α = 57.16°
Answer
α = 57.16°
7.Work & energy
Answer: v = 8.427 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy balance along the slope
The block drops a height d·sin θ while friction removes μmg·cos θ·d. The mass cancels.
½v² = g·d·(sin θ − μ·cos θ)
v = √(2·9.81·18·(0.342 − 0.15·0.9397)) = 8.427 m/s
Answer
v = 8.427 m/s
8.Work & energy
Answer: v = 2.671 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy released and lost
m₂g·d = 58.86·1 = 58.86 J
μ·m₁g·d = 0.4·49.05·1 = 19.62 J
Kinetic energy of both blocks
½(m₁ + m₂)v² = 39.24 → v = √(2·39.24/11) = 2.671 m/s
Answer
v = 2.671 m/s
9.Momentum & collisions
Answer: ΔK/K = 54.55 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 500·25/1100 = 11.36 m/s
Kinetic energy before and after
Kbefore = ½·500·25² = 156250 J
Kafter = ½·1100·11.36² = 71023 J
Fraction lost
ΔK/K = 85227/156250 = 54.55 %
Answer
ΔK/K = 54.55 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: Favg = 1183 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(15 + 28) = 23.65 N·s
Average force
Favg = J/Δt = 23.65/0.02 = 1183 N
Answer
Favg = 1183 N
11.Hydrostatic force
Answer: F = 165.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 2.5/2 = 2.25 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.25·7.5 = 165.5 kN
Answer
F = 165.5 kN
12.Hydrostatic force
Answer: F = 207.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2.5/2 = 2.75 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·2.75·7.5 = 207.4 kN
Answer
F = 207.4 kN
13.Continuity & Bernoulli
Answer: Q = 8.485 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·5.5) = 10.39 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli from the surface to the jet
v = √(2·(110000/1000 + 9.81·3.5)) = 16.99 m/s
Answer
v = 16.99 m/s
15.Ideal gas law
Answer: P = 521.4 kPa
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = m/M = 380/44.01 = 8.634 mol
T = 90 + 273.15 = 363.1 K
Pressure
P = nRT/V = 8.634·8.314·363.1/0.05 = 521.4 kPa
Answer
P = 521.4 kPa
16.Ideal gas law
Answer: V2 = 28.48 L
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 283.1 K, T2 = 403.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(150/150)·(403.1/283.1) = 28.48 L
Answer
V2 = 28.48 L
17.Heat engines & refrigerators
Answer: Wmax = 1339 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
TL = 25 + 273.15 = 298.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 298.1/823.1 = 63.78 %
Maximum work
Wmax = ηmax·QH = 0.6378·2100 = 1339 kJ
Answer
Wmax = 1339 kJ
18.Heat engines & refrigerators
Answer: Tm = 620 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1200 + 273.15 = 1473 K
TL = 40 + 273.15 = 313.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (1473 + 313.1)/2 = 893.2 K = 620 °C
Answer
Tm = 620 °C
19.Waves, sound & optics
Answer: β = 76 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Intensity
I = P/(4πr²) = 3.979 × 10⁻⁵ W/m²
Level
β = 10·log₁₀(3.979 × 10⁻⁵/10⁻¹²) = 76 dB
Answer
β = 76 dB
20.Waves, sound & optics
Answer: θ1 = 19.15 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …