Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 120 km/h brakes with a constant deceleration of 3 m/s² until it stops. How long does braking take? Find t.
v₀ = 120 km/ha = −3 m/s²v = 0
t = s
2.KinematicsHard
Ball A is dropped from rest from a height of 30 m. At the same instant ball B is thrown straight up from the ground directly below at 25 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 30 mv0B = 25 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 10 kg block slides down a slope at 40° to the horizontal. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 10 kgθ = 40°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 45 N pulls the front 10 kg block; the 11 kg block is towed behind. The coefficient of kinetic friction is 0.15 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 11 kgm2 = 10 kgF = 45 Nμ = 0.15g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 70° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 14 m/sθ = 70°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is thrown from ground level at 29 m/s and 45° above the horizontal. It lands on the flat roof of a building 10 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 29 m/sθ = 45°hroof = 10 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 0.5 kg block slides 4 m down a slope at 25° to the horizontal, with a coefficient of kinetic friction of 0.35. Find the work Wf done against friction.
m = 0.5 kgθ = 25°μ = 0.35d = 4 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 10 kg block is released from rest at height 2 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.3) and then runs onto a spring (k = 4000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 10 kgh = 2 mL = 3 mμ = 0.3k = 4000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 0.5 kg glider moving at 3 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 0.5 kgm2 = 1 kgv1 = 3 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 5 g bullet is fired horizontally into a 3 kg block hanging from light strings 0.7 m long, and stays in it. The strings swing out to a largest angle of 40° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 3 kgL = 0.7 mθ = 40°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of glycerin, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 3 mb = 2 mρ = 1260 kg/m³g = 9.81 m/s²
F = kN
13.Continuity & BernoulliMedium
Water drains from a large open tank through a sharp-edged orifice with a diameter of 25 mm. The water level is kept 5.5 m above the orifice and the discharge coefficient is 0.64. Find the flow rate Q. Use g = 9.81 m/s².
d = 25 mmh = 5.5 mCd = 0.64g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A horizontal venturi meter (inlet 100 mm, throat 50 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 380 mm. The discharge coefficient is 0.99. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 550 °C and a cold reservoir at 5 °C. It takes in 1800 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 550 °CTL = 5 °CQH = 1800 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
Two Carnot engines work in series. Engine A receives heat from a reservoir at 1100 °C and rejects heat to an intermediate reservoir at temperature Tm. Engine B takes all that heat and rejects heat to a reservoir at 35 °C. Both engines produce the same work. Find Tm in °C.
TH = 1100 °CTL = 35 °C
Tm = °C
19.Waves, sound & opticsMedium
Light travels in crown glass (n = 1.50) towards a flat boundary with acrylic (n = 1.49). Find the critical angle θc beyond which it is totally reflected.
n1 = 1.50n2 = 1.49
θc = °
20.Waves, sound & opticsHard
Light of wavelength 633 nm falls at right angles on a grating with 100 lines per millimetre. Find the angle θ1 of the order-1 maximum.
N = 100 mm⁻¹λ = 633 nmm = 1
θ1 = °
3Solutions
1.Kinematics
Answer: t = 11.11 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 120/3.6 = 33.33 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 33.33/3 = 11.11 s
Answer
t = 11.11 s
2.Kinematics
Answer: t = 1.2 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
30 − ½g·t² = 25·t − ½g·t² → t = 30/25 = 1.2 s
Answer
t = 1.2 s
3.Newton’s laws
Answer: a = 4.051 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: t = 2.682 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 14·cos 70° = 4.788 m/s
vy = v0·sin θ = 14·sin 70° = 13.16 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·13.16/9.81 = 2.682 s
Answer
t = 2.682 s
6.Projectile motion
Answer: x = 74.17 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 20.51 m/s, vy = 20.51 m/s
Time to land on the roof
Larger root: the ball is descending.
10 = 20.51·t − 4.905·t²
t = (20.51 + √(20.51² − 2·9.81·10))/9.81 = 3.617 s
Horizontal distance
x = vx·t = 20.51·3.617 = 74.17 m
Answer
x = 74.17 m
7.Work & energy
Answer: Wf = 6.224 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 4.905·0.9063 = 4.445 N
F = μN = 0.35·4.445 = 1.556 N
Work against friction
Wf = F·d = 1.556·4 = 6.224 J
Answer
Wf = 6.224 J
8.Work & energy
Answer: v = 4.646 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 98.1·(2 − 0.3·3) = 107.9 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·1.1) = 4.646 m/s
Answer
v = 4.646 m/s
9.Momentum & collisions
Answer: v′1 = −1 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (0.5 − 1)/(0.5 + 1)·3 = −1 m/s
v′2 = 2·0.5/(0.5 + 1)·3 = 2 m/s
Answer
v′1 = −1 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: v = 1077 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.7·(1 − cos 40°) = 0.1638 m
Speed after impact
V = √(2·9.81·0.1638) = 1.793 m/s
Collision
v = (m + M)·V/m = 3.005·1.793/0.005 = 1077 m/s
Answer
v = 1077 m/s
11.Hydrostatic force
Answer: F = 25.75 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1.5/2 = 1.75 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.75·1.5 = 25.75 kN
Answer
F = 25.75 kN
12.Hydrostatic force
Answer: F = 185.4 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 3/2 = 2.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·2.5·6 = 185.4 kN
Answer
F = 185.4 kN
13.Continuity & Bernoulli
Answer: Q = 3.263 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·5.5) = 10.39 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.38 = 46970 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/823.1 = 66.21 %
Maximum work
Wmax = ηmax·QH = 0.6621·1800 = 1192 kJ
Answer
Wmax = 1192 kJ
18.Heat engines & refrigerators
Answer: Tm = 567.5 °C
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 1100 + 273.15 = 1373 K
TL = 35 + 273.15 = 308.1 K
Equal work
W = Q·(1 − Tlow/Thigh) and Q/T is the same at every reservoir, so W is proportional to the temperature drop.
Tm = (1373 + 308.1)/2 = 840.7 K = 567.5 °C
Answer
Tm = 567.5 °C
19.Waves, sound & optics
Answer: θc = 83.38 °
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Refraction at 90°
sin θc = n₂/n₁ = 1.49/1.50 = 0.9933
Critical angle
θc = arcsin(0.9933) = 83.38°
Answer
θc = 83.38°
20.Waves, sound & optics
Answer: θ1 = 3.629 °
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …