Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 180 km/h to take off and the usable runway is 800 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 180 km/hs = 800 m
a = m/s²
2.KinematicsHard
A stone is dropped from rest into a well. The splash is heard 4.2 s after the stone is released. The speed of sound is 343 m/s; ignore air resistance and use g = 9.81 m/s². Find the depth d of the well.
ttotal = 4.2 svsound = 343 m/sg = 9.81 m/s²
d = m
3.Newton’s lawsMedium
A 20 kg sled is pulled across level snow by a rope at 15° above the horizontal with a force of 150 N. The coefficient of kinetic friction is 0.4. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 20 kgF = 150 Nθ = 15°μ = 0.4g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 20° with a speed of 3 m/s. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 3 m/sθ = 20°μ = 0.3g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is kicked from level ground at 26 m/s and 25° above the horizontal towards a wall 21 m away. Ignore air resistance and use g = 9.81 m/s². At what height y does the ball pass the wall?
v₀ = 26 m/sθ = 25°x = 21 mg = 9.81 m/s²
y = m
6.Projectile motionHard
A ball is launched at 50° above horizontal from the top of a 15 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 30 m/sθ = 50°h = 15 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A 2.5 kg block slides 11 m down a slope at 35° to the horizontal, with a coefficient of kinetic friction of 0.15. Find the work Wf done against friction.
m = 2.5 kgθ = 35°μ = 0.15d = 11 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
An 8 kg block starts from rest at the bottom of a 20° slope and is pulled up the slope by a constant force of 45 N parallel to the slope. The coefficient of kinetic friction is 0.1. Find the speed v of the block after it has moved 5 m up the slope.
A 500 kg car moving at 20 m/s runs into a stationary 1000 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 500 kgv1 = 20 m/sm2 = 1000 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.15 kg ball hits a wall at 10 m/s and bounces straight back at 19 m/s. The contact lasts 10 ms. Find the average force Favg of the wall on the ball.
m = 0.15 kgvin = 10 m/svout = 19 m/sΔt = 10 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of oil, with its top edge 2 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 2 mH = 1 mb = 2 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal pipe that narrows from 100 mm to 75 mm. In the wide section the pressure is 180 kPa and the velocity is 2.5 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 200 mm to 100 mm while rising 2 m. At section 1 the pressure is 280 kPa and the velocity is 1.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at 2 °C by removing 2.5 kW of heat, and rejects heat to the surroundings at 28 °C. Find the rate Q̇H at which it rejects heat.
TL = 2 °CTH = 28 °CQ̇L = 2.5 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 90 kW of heat from a source at 700 °C and rejects heat to the surroundings at 20 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -30 °C and also rejects heat to the surroundings at 20 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 700 °CT0 = 20 °CTL = -30 °CQ̇H = 90 kW
Q̇L = kW
19.Waves, sound & opticsMedium
An object stands 10 cm in front of a thin diverging lens with a focal length of 15 cm. Find the magnification m (negative for an inverted image).
do = 10 cmf = −15 cm
m =
20.Waves, sound & opticsHard
Light of wavelength 532 nm falls on two slits 0.25 mm apart. The screen is 2.5 m away. Find the distance y5 from the central bright fringe to bright fringe number 5.
λ = 532 nmd = 0.25 mmL = 2.5 mm = 5
y5 = mm
3Solutions
1.Kinematics
Answer: a = 1.563 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 180/3.6 = 50 m/s
Acceleration
a = v²/(2s) = 50²/(2·800) = 1.563 m/s²
Answer
a = 1.563 m/s²
2.Kinematics
Answer: d = 77.47 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Two parts of the time
½·9.81·t₁² = 343·(4.2 − t₁)
4.905·t₁² + 343·t₁ − 1441 = 0
Fall time
Only the positive root is physical.
t₁ = (−343 + √(343² + 4·4.905·1441))/(2·4.905) = 3.974 s
Depth
d = ½·9.81·3.974² = 77.47 m
Answer
d = 77.47 m
3.Newton’s laws
Answer: a = 4.097 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 196.2 − 150·sin 15° = 157.4 N
Horizontal forces
m·a = F·cos θ − μ·N = 144.9 − 62.95
a = 81.94/20 = 4.097 m/s²
Answer
a = 4.097 m/s²
4.Newton’s laws
Answer: d = 0.7352 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 20° + 0.3·cos 20°) = 6.121 m/s²
Distance
d = v₀²/(2a) = 3²/(2·6.121) = 0.7352 m
Answer
d = 0.7352 m
5.Projectile motion
Answer: y = 5.897 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Time to the wall
vx = 26·cos 25° = 23.56 m/s
t = x/vx = 21/23.56 = 0.8912 s
Height at that time
y = 10.99·0.8912 − ½·9.81·0.8912² = 5.897 m
Answer
y = 5.897 m
The ball is still rising at the wall.
6.Projectile motion
Answer: t = 5.266 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 30·cos 50° = 19.28 m/s
vy = v0·sin θ = 30·sin 50° = 22.98 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 15 + 22.98·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (22.98 + √(528.1 + 294.3))/9.81 = 5.266 s
Answer
t = 5.266 s
7.Work & energy
Answer: Wf = 33.15 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 24.53·0.8192 = 20.09 N
F = μN = 0.15·20.09 = 3.013 N
Work against friction
Wf = F·d = 3.013·11 = 33.15 J
Answer
Wf = 33.15 J
8.Work & energy
Answer: v = 3.671 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Forces along the slope
m·g = 8·9.81 = 78.48 N
mg·sin θ = 26.84 N
μ·mg·cos θ = 7.375 N
Work–energy
½mv² = (45 − 34.22)·5 = 53.92 J
v = √(2·53.92/8) = 3.671 m/s
Answer
v = 3.671 m/s
9.Momentum & collisions
Answer: ΔK = 66667 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 500·20/1500 = 6.667 m/s
Kinetic energy before and after
Kbefore = ½·500·20² = 100000 J
Kafter = ½·1500·6.667² = 33333 J
Energy lost
ΔK = 100000 − 33333 = 66667 J
Answer
ΔK = 66667 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: Favg = 435 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.15·(19 + 10) = 4.35 N·s
Average force
Favg = J/Δt = 4.35/0.01 = 435 N
Answer
Favg = 435 N
11.Hydrostatic force
Answer: F = 176.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 3/2 = 4 m
A = H·b = 3·1.5 = 4.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4·4.5 = 176.6 kN
Answer
F = 176.6 kN
12.Hydrostatic force
Answer: ycp = 2.533 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1/2 = 2.5 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·2.5·2 = 43.16 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 28 + 273.15 = 301.1 K
TL = 2 + 273.15 = 275.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 2.5·301.1/275.1 = 2.736 kW
Answer
Q̇H = 2.736 kW
Power input: Ẇ = 0.2362 kW.
18.Heat engines & refrigerators
Answer: Q̇L = 305.8 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 700 + 273.15 = 973.1 K
T0 = 20 + 273.15 = 293.1 K
TL = -30 + 273.15 = 243.1 K
Engine work
η = 1 − 293.1/973.1 = 0.6988
Ẇ = 0.6988·90 = 62.89 kW
Heat removed by the refrigerator
COPR = 243.1/(293.1 − 243.1) = 4.863
Q̇L = 4.863·62.89 = 305.8 kW
Answer
Q̇L = 305.8 kW
19.Waves, sound & optics
Answer: m = 0.6
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−15) − 1/10
di = −6 cm
Magnification
m = −di/do = −(−6)/10 = 0.6
Answer
m = 0.6
20.Waves, sound & optics
Answer: y5 = 26.6 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …