Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 2.5 m/s² along a runway. Find its speed v after 900 m.
v₀ = 0a = 2.5 m/s²s = 900 m
v = m/s
2.KinematicsHard
A ball is thrown straight up at 20 m/s from the edge of a roof 5 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 20 m/sh₀ = 5 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 10 kg sled is pulled across level snow by a rope at 35° above the horizontal with a force of 30 N. The coefficient of kinetic friction is 0.2. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 10 kgF = 30 Nθ = 35°μ = 0.2g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 3.5 kg block on a ramp at 35° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 5 kg mass. The hanging mass moves down. The coefficient of kinetic friction between block and ramp is 0.25. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 3.5 kgm2 = 5 kgθ = 35°μ = 0.25g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 55° above horizontal from level ground. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 24 m/sθ = 55°g = 9.81 m/s²
t = s
6.Projectile motionHard
A ball is launched at 15° above horizontal from the top of a 45 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 35 m/sθ = 15°h = 45 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 0.5 kg block slides 18 m down a slope at 30° to the horizontal, with a coefficient of kinetic friction of 0.25. Find the work Wf done against friction.
m = 0.5 kgθ = 30°μ = 0.25d = 18 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 5 kg block is released from rest at height 4.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.1) and then runs onto a spring (k = 800 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 5 kgh = 4.5 mL = 3 mμ = 0.1k = 800 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 0.5 kg glider moving at 12 m/s makes a perfectly elastic head-on collision with a 2.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 0.5 kgm2 = 2.5 kgv1 = 12 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 10 g bullet is fired horizontally into a 4 kg block hanging from light strings 1.3 m long, and stays in it. The strings swing out to a largest angle of 20° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 10 gM = 4 kgL = 1.3 mθ = 20°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 75 mm to 25 mm. In the wide section the pressure is 310 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 75 mm to 50 mm while rising 6 m. At section 1 the pressure is 310 kPa and the velocity is 1.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 275 °C and a cold reservoir at 30 °C. It takes in 3700 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 275 °CTL = 30 °CQH = 3700 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -25 °C in a kitchen at 35 °C, removing heat from the cold space at 3 kW. Find the minimum power input Ẇmin.
TH = 35 °CTL = -25 °CQ̇L = 3 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 50 cm in front of a thin converging lens with a focal length of 25 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 50 cmf = 25 cm
di = cm
20.Waves, sound & opticsHard
An object is 40 cm in front of a convex mirror with a radius of curvature of 20 cm. Find the magnification m (negative for an inverted image).
do = 40 cmR = 20 cm
m =
3Solutions
1.Kinematics
Answer: v = 67.08 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·2.5·900) = 67.08 m/s
Answer
v = 67.08 m/s
(241.5 km/h)
2.Kinematics
Answer: t = 4.314 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−5 = 20·t − ½·9.81·t²
4.905·t² − 20·t − 5 = 0
Solve the quadratic
Only the positive root is physical.
t = (20 + √(20² + 2·9.81·5))/9.81 = 4.314 s
Answer
t = 4.314 s
3.Newton’s laws
Answer: a = 0.8396 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 98.1 − 30·sin 35° = 80.89 N
Horizontal forces
m·a = F·cos θ − μ·N = 24.57 − 16.18
a = 8.396/10 = 0.8396 m/s²
Answer
a = 0.8396 m/s²
4.Newton’s laws
Answer: T = 35.92 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 49.05 N
m₁·g·sin θ = 19.69 N
μ·m₁·g·cos θ = 7.031 N
Acceleration of the system
a = (49.05 − 19.69 − 7.031)/8.5 = 2.626 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 5·(9.81 − 2.626) = 35.92 N
Answer
T = 35.92 N
5.Projectile motion
Answer: t = 4.008 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 55° = 13.77 m/s
vy = v0·sin θ = 24·sin 55° = 19.66 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·19.66/9.81 = 4.008 s
Answer
t = 4.008 s
6.Projectile motion
Answer: x = 138.3 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 35·cos 15° = 33.81 m/s
vy = v0·sin θ = 35·sin 15° = 9.059 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 45 + 9.059·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (9.059 + √(82.06 + 882.9))/9.81 = 4.09 s
Horizontal distance
x = vx·t = 33.81·4.09 = 138.3 m
Answer
x = 138.3 m
7.Work & energy
Answer: Wf = 19.12 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 4.905·0.866 = 4.248 N
F = μN = 0.25·4.248 = 1.062 N
Work against friction
Wf = F·d = 1.062·18 = 19.12 J
Answer
Wf = 19.12 J
8.Work & energy
Answer: v = 9.078 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(4.5 − 0.1·3) = 206 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·4.2) = 9.078 m/s
Answer
v = 9.078 m/s
9.Momentum & collisions
Answer: v′1 = −8 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (0.5 − 2.5)/(0.5 + 2.5)·12 = −8 m/s
v′2 = 2·0.5/(0.5 + 2.5)·12 = 4 m/s
Answer
v′1 = −8 m/s
The minus sign means the first glider bounces back.
10.Momentum & collisions
Answer: v = 497.3 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 1.3·(1 − cos 20°) = 0.0784 m
Speed after impact
V = √(2·9.81·0.0784) = 1.24 m/s
Collision
v = (m + M)·V/m = 4.01·1.24/0.01 = 497.3 m/s
Answer
v = 497.3 m/s
11.Hydrostatic force
Answer: F = 47.82 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1.5/2 = 3.25 m
A = H·b = 1.5·1 = 1.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·1.5 = 47.82 kN
Answer
F = 47.82 kN
12.Hydrostatic force
Answer: F = 60.33 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2/2 = 1.5 m
A = H·b = 2·2 = 4 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·1.5·4 = 60.33 kN
Answer
F = 60.33 kN
13.Continuity & Bernoulli
Answer: p2 = 287.5 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 523.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(100/500)·(523.1/293.1) = 7.138 L
Answer
V2 = 7.138 L
17.Heat engines & refrigerators
Answer: Wmax = 1654 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 275 + 273.15 = 548.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/548.1 = 44.7 %
Maximum work
Wmax = ηmax·QH = 0.447·3700 = 1654 kJ
Answer
Wmax = 1654 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.7254 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 3/4.136 = 0.7254 kW
Answer
Ẇmin = 0.7254 kW
19.Waves, sound & optics
Answer: di = 50 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/25 − 1/50
di = 50 cm
Ray diagram
real, on the far side of the lens
Answer
di = 50 cm
20.Waves, sound & optics
Answer: m = 0.2
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.