Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 54 km/h brakes with a constant deceleration of 5.5 m/s² until it stops. Find the braking distance s.
v₀ = 54 km/ha = −5.5 m/s²v = 0
s = m
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 28 m/s² for 1 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax the rocket reaches.
a = 28 m/s²t1 = 1 sg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 20 kg sled is pulled across level snow by a rope at 40° above the horizontal with a force of 140 N. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 20 kgF = 140 Nθ = 40°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 25° with a speed of 9.5 m/s. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 9.5 m/sθ = 25°μ = 0.15g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched at 20° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 24 m/sθ = 20°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 23 m/s and 45° above the horizontal from the top of a 50 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 23 m/sθ = 45°h = 50 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A 10 kg ball hangs on a light string of length 3 m. It is pulled aside until the string makes 50° with the vertical and released from rest. Find the tension T in the string when the ball passes the lowest point.
m = 10 kgL = 3 mθ = 50°g = 9.81 m/s²
T = N
8.Work & energyHard
A spring of stiffness 500 N/m at the bottom of a 30° slope is compressed by 15 cm against a 1 kg block and released. The coefficient of kinetic friction between block and slope is 0.3. How far d up the slope does the block travel from the release point before it stops? (Ignore the short distance over which the spring pushes, i.e. take friction and gravity over the whole distance d.)
An 8 g bullet is fired horizontally into a 5 kg wooden block hanging on light strings, and stays inside it. The block swings up until it is 20 cm higher than at the start. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 8 gM = 5 kgh = 20 cmg = 9.81 m/s²
v = m/s
10.Momentum & collisionsHard
A 5 g bullet is fired horizontally into a 1.5 kg block hanging from light strings 0.5 m long, and stays in it. The strings swing out to a largest angle of 15° from the vertical. Use g = 9.81 m/s². Find the speed v of the bullet before impact.
m = 5 gM = 1.5 kgL = 0.5 mθ = 15°g = 9.81 m/s²
v = m/s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of oil, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 150 mm to 40 mm. In the wide section the pressure is 400 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A hose with an inner diameter of 32 mm siphons water from an open tank. The highest point C of the hose is 0.5 m above the water surface, and the outlet (open to the air) is 3.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the absolute pressure pC at point C. The atmospheric pressure is 101.3 kPa.
A heat engine works between a hot reservoir at 650 °C and a cold reservoir at 30 °C. It takes in 1300 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 650 °CTL = 30 °CQH = 1300 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat engine takes in 1400 kJ of heat from a reservoir at 350 °C, produces 490 kJ of work and rejects the rest to a reservoir at 35 °C, per cycle. Find the total entropy generated Sgen per cycle.
TH = 350 °CTL = 35 °CQH = 1400 kJW = 490 kJ
Sgen = kJ/K
19.Waves, sound & opticsMedium
A pipe open at both ends is 0.4 m long. The speed of sound is 343 m/s. Find the frequency f4 of its harmonic number 4.
v = 343 m/sn = 4L = 0.4 m
f4 = Hz
20.Waves, sound & opticsHard
Light of wavelength 650 nm falls on two slits 0.4 mm apart. The screen is 1.2 m away. Find the distance y1 from the central bright fringe to bright fringe number 1.
λ = 650 nmd = 0.4 mmL = 1.2 mm = 1
y1 = mm
3Solutions
1.Kinematics
Answer: s = 20.45 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 54/3.6 = 15 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 15²/(2·5.5) = 20.45 m
Answer
s = 20.45 m
2.Kinematics
Answer: hmax = 53.96 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 28·1 = 28 m/s
h₁ = ½·28·1² = 14 m
Free flight up
At the top the velocity is zero.
Δh = v₁²/(2g) = 28²/(2·9.81) = 39.96 m
hmax = 14 + 39.96 = 53.96 m
Answer
hmax = 53.96 m
3.Newton’s laws
Answer: a = 3.769 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 196.2 − 140·sin 40° = 106.2 N
Horizontal forces
m·a = F·cos θ − μ·N = 107.2 − 31.86
a = 75.38/20 = 3.769 m/s²
Answer
a = 3.769 m/s²
4.Newton’s laws
Answer: d = 8.235 m
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 25° + 0.15·cos 25°) = 5.48 m/s²
Distance
d = v₀²/(2a) = 9.5²/(2·5.48) = 8.235 m
Answer
d = 8.235 m
5.Projectile motion
Answer: x = 37.74 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 24·cos 20° = 22.55 m/s
vy = v0·sin θ = 24·sin 20° = 8.208 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·8.208/9.81 = 1.673 s
Horizontal distance
x = vx·t = 22.55·1.673 = 37.74 m
Answer
x = 37.74 m
6.Projectile motion
Answer: α = 65.26 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 23·cos 45° = 16.26 m/s
vy0 = 23·sin 45° = 16.26 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(16.26² + 2·9.81·50) = 35.29 m/s
Impact angle
tan α = vy/vx = 35.29/16.26 → α = 65.26°
Answer
α = 65.26°
7.Work & energy
Answer: T = 168.2 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the bottom
v² = 2gL(1 − cos θ) = 2·9.81·3·(1 − cos 50°) = 21.03 m²/s²
Forces at the bottom
m·g = 10·9.81 = 98.1 N
T = mg + mv²/L = 98.1 + 10·21.03/3 = 168.2 N
Answer
T = 168.2 N
Check: T = mg(3 − 2cos θ) = 168.2 N.
8.Work & energy
Answer: d = 0.7547 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Spring energy
x = 15 cm = 0.15 m
½kx² = ½·500·0.15² = 5.625 J
Energy balance along the slope
m·g = 1·9.81 = 9.81 N
½kx² = mg·d·(sin θ + μ·cos θ)
d = 5.625/(9.81·(0.5 + 0.3·0.866)) = 0.7547 m
Answer
d = 0.7547 m
9.Momentum & collisions
Answer: v = 1240 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Swing after impact
V = √(2·g·h) = √(2·9.81·0.2) = 1.981 m/s
Collision
m·v = (m + M)·V → v = (0.008 + 5)·1.981/0.008 = 1240 m/s
Answer
v = 1240 m/s
10.Momentum & collisions
Answer: v = 174 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Rise of the block
h = L·(1 − cos θ) = 0.5·(1 − cos 15°) = 0.01704 m
Speed after impact
V = √(2·9.81·0.01704) = 0.5782 m/s
Collision
v = (m + M)·V/m = 1.505·0.5782/0.005 = 174 m/s
Answer
v = 174 m/s
11.Hydrostatic force
Answer: F = 323.7 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 3/2 = 5.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.5·6 = 323.7 kN
Answer
F = 323.7 kN
12.Hydrostatic force
Answer: F = 53.42 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 1.5/2 = 2.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·2.75·2.25 = 53.42 kN
Answer
F = 53.42 kN
13.Continuity & Bernoulli
Answer: p2 = 344.7 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
If this pressure falls to the vapour pressure of the water, the siphon stops working.
15.Ideal gas law
Answer: V = 19.95 L
Ideal gas law: PV = nRT, with n = m/M.
Moles
n = 200/44.01 = 4.544 mol
T = 70 + 273.15 = 343.1 K
Volume
V = nRT/P = 4.544·8.314·343.1/650 = 19.95 L
Answer
V = 19.95 L
16.Ideal gas law
Answer: ρ = 3.436 kg/m³
Ideal gas density: ρ = PM/(RT).
Rearrange the gas law
PV = (m/M)RT → ρ = m/V = PM/(RT)
T = 70 + 273.15 = 343.1 K
Density
ρ = 350·28.01/(8.314·343.1) = 3.436 kg/m³
Answer
ρ = 3.436 kg/m³
17.Heat engines & refrigerators
Answer: Wmax = 873.1 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 650 + 273.15 = 923.1 K
TL = 30 + 273.15 = 303.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 303.1/923.1 = 67.16 %
Maximum work
Wmax = ηmax·QH = 0.6716·1300 = 873.1 kJ
Answer
Wmax = 873.1 kJ
18.Heat engines & refrigerators
Answer: Sgen = 0.7065 kJ/K
Entropy generation: over a full cycle the working fluid has no net entropy change. The hot reservoir loses QH/TH and the cold reservoir gains QL/TL. Their sum is the entropy generated, which is zero for a reversible cycle and positive for every real one.
Heat rejected
QL = QH − W = 1400 − 490 = 910 kJ
Absolute temperatures
TH = 350 + 273.15 = 623.1 K
TL = 35 + 273.15 = 308.1 K
Entropy changes of the reservoirs
ΔSH = −1400/623.1 = −2.247 kJ/K
ΔSL = 910/308.1 = 2.953 kJ/K
Sgen = 2.953 − 2.247 = 0.7065 kJ/K
Answer
Sgen = 0.7065 kJ/K
Sgen > 0, so the engine is possible but irreversible.
19.Waves, sound & optics
Answer: f4 = 1715 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.4/4 = 0.2 m
Frequency
f = v/λ = 343/0.2 = 1715 Hz
Answer
f4 = 1715 Hz
20.Waves, sound & optics
Answer: y1 = 1.95 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …