Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 100 km/h brakes with a constant deceleration of 6.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 100 km/ha = −6.5 m/s²v = 0
t = s
2.KinematicsHard
Ball A is dropped from rest from a height of 25 m. At the same instant ball B is thrown straight up from the ground directly below at 15 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 25 mv0B = 15 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 35 kg sled is pulled across level snow by a rope at 25° above the horizontal with a force of 160 N. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 35 kgF = 160 Nθ = 25°μ = 0.3g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 2.5 kg block on a ramp at 35° is connected by a light string over a frictionless pulley at the top of the ramp to a hanging 4.5 kg mass. The hanging mass moves down. The ramp is frictionless. Use g = 9.81 m/s². Find the tension T in the string.
m1 = 2.5 kgm2 = 4.5 kgθ = 35°μ = 0g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 45° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 30 m/sθ = 45°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 13 m/s and 30° above the horizontal from the top of a 45 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 13 m/sθ = 30°h = 45 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 2.5 kg block slides 5 m down a slope at 15° to the horizontal, with a coefficient of kinetic friction of 0.15. Find the work Wf done against friction.
m = 2.5 kgθ = 15°μ = 0.15d = 5 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 4 kg block is released from rest at height 1 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3 m long (μ = 0.2) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 4 kgh = 1 mL = 3 mμ = 0.2k = 1000 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 4 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 3.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 4 kgm2 = 3.5 kgv1 = 11 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 22 m/s and bounces straight back at 8 m/s. The contact lasts 50 ms. Find the average force Favg of the wall on the ball.
m = 0.55 kgvin = 22 m/svout = 8 m/sΔt = 50 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 1.5 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of seawater, with its top edge 0.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 30 mm. The water level is kept 3.5 m above the orifice and the discharge coefficient is 0.64. Find the flow rate Q. Use g = 9.81 m/s².
d = 30 mmh = 3.5 mCd = 0.64g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 75 mm to 50 mm while rising 8 m. At section 1 the pressure is 300 kPa and the velocity is 3 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 800 °C and a cold reservoir at 5 °C. It takes in 2200 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 800 °CTL = 5 °CQH = 2200 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump keeps a house at 22 °C while it is 2 °C outside, delivering 8 kW of heat to the house. Find the highest possible coefficient of performance COPmax.
TH = 22 °CTL = 2 °CQ̇H = 8 kW
COPmax =
19.Waves, sound & opticsMedium
An object stands 50 cm in front of a thin diverging lens with a focal length of 10 cm. Find the magnification m (negative for an inverted image).
do = 50 cmf = −10 cm
m =
20.Waves, sound & opticsHard
Light of wavelength 600 nm falls on two slits 0.15 mm apart. The screen is 2.5 m away. Find the distance y5 from the central bright fringe to bright fringe number 5.
λ = 600 nmd = 0.15 mmL = 2.5 mm = 5
y5 = mm
3Solutions
1.Kinematics
Answer: t = 4.274 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 100/3.6 = 27.78 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 27.78/6.5 = 4.274 s
Answer
t = 4.274 s
2.Kinematics
Answer: t = 1.667 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
25 − ½g·t² = 15·t − ½g·t² → t = 25/15 = 1.667 s
Answer
t = 1.667 s
3.Newton’s laws
Answer: a = 1.78 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 343.4 − 160·sin 25° = 275.7 N
Horizontal forces
m·a = F·cos θ − μ·N = 145 − 82.72
a = 62.29/35 = 1.78 m/s²
Answer
a = 1.78 m/s²
4.Newton’s laws
Answer: T = 24.81 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the string
m₂·g = 44.15 N
m₁·g·sin θ = 14.07 N
μ·m₁·g·cos θ = 0 N
Acceleration of the system
a = (44.15 − 14.07 − 0)/7 = 4.297 m/s²
Tension from the hanging mass
m2·g − T = m2·a → T = 4.5·(9.81 − 4.297) = 24.81 N
Answer
T = 24.81 N
5.Projectile motion
Answer: H = 22.94 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 30·cos 45° = 21.21 m/s
vy = v0·sin θ = 30·sin 45° = 21.21 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 21.21²/(2·9.81) = 22.94 m
Answer
H = 22.94 m
6.Projectile motion
Answer: H = 47.15 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 13·sin 30° = 6.5 m/s
Rise above the cliff
Δh = vy²/(2g) = 6.5²/(2·9.81) = 2.153 m
Height above the ground
H = 45 + 2.153 = 47.15 m
Answer
H = 47.15 m
7.Work & energy
Answer: Wf = 17.77 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 24.53·0.9659 = 23.69 N
F = μN = 0.15·23.69 = 3.553 N
Work against friction
Wf = F·d = 3.553·5 = 17.77 J
Answer
Wf = 17.77 J
8.Work & energy
Answer: x = 17.72 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(1 − 0.2·3) = 15.7 J
Maximum compression
½kx² = 15.7 → x = √(2·15.7/1000) = 0.1772 m = 17.72 cm
Answer
x = 17.72 cm
9.Momentum & collisions
Answer: v′2 = 11.73 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (4 − 3.5)/(4 + 3.5)·11 = 0.7333 m/s
v′2 = 2·4/(4 + 3.5)·11 = 11.73 m/s
Answer
v′2 = 11.73 m/s
10.Momentum & collisions
Answer: Favg = 330 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(8 + 22) = 16.5 N·s
Average force
Favg = J/Δt = 16.5/0.05 = 330 N
Answer
Favg = 330 N
11.Hydrostatic force
Answer: F = 73.58 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1.5 + 2/2 = 2.5 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·3 = 73.58 kN
Answer
F = 73.58 kN
12.Hydrostatic force
Answer: F = 45.25 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 0.5 + 2/2 = 1.5 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·1.5·3 = 45.25 kN
Answer
F = 45.25 kN
13.Continuity & Bernoulli
Answer: Q = 3.749 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·3.5) = 8.287 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 800 + 273.15 = 1073 K
TL = 5 + 273.15 = 278.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 278.1/1073 = 74.08 %
Maximum work
Wmax = ηmax·QH = 0.7408·2200 = 1630 kJ
Answer
Wmax = 1630 kJ
18.Heat engines & refrigerators
Answer: COPmax = 14.76
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/(−10) − 1/50
di = −8.333 cm
Magnification
m = −di/do = −(−8.333)/50 = 0.1667
Answer
m = 0.1667
20.Waves, sound & optics
Answer: y5 = 50 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …