Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 50 km/h brakes with a constant deceleration of 4 m/s² until it stops. Find the braking distance s.
v₀ = 50 km/ha = −4 m/s²v = 0
s = m
2.KinematicsHard
A tram starts from rest and accelerates at 1.5 m/s² for 10 s, then runs at constant speed for 29 s, and finally brakes at 2 m/s² until it stops. Find the total distance s between the two stops.
a1 = 1.5 m/s²t1 = 10 st2 = 29 sa3 = −2 m/s²
s = m
3.Newton’s lawsMedium
A 40 kg box is pushed up a ramp at 20° to the horizontal at constant speed, by a force parallel to the ramp. The coefficient of kinetic friction is 0.3. Use g = 9.81 m/s². Find the pushing force F.
m = 40 kgθ = 20°μ = 0.3g = 9.81 m/s²
F = N
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 100 N pulls the front 10 kg block; the 5 kg block is towed behind. The coefficient of kinetic friction is 0.3 for both blocks. Use g = 9.81 m/s². Find the acceleration a of the blocks.
m1 = 5 kgm2 = 10 kgF = 100 Nμ = 0.3g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 30 m/s and must land 70 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 30 m/sR = 70 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 20 m cliff. Ignore air resistance. Find the time of flight t until the ball hits the ground.
v0 = 34 m/sθ = 45°h = 20 mg = 9.81 m/s²
t = s
7.Work & energyMedium
A car travelling at 100 km/h on a level road brakes hard and skids to a stop with its wheels locked. The coefficient of kinetic friction between the tyres and the road is 0.4. Find the stopping distance d.
v = 100 km/hμ = 0.4g = 9.81 m/s²
d = m
8.Work & energyHard
A 1 kg block is released from rest at height 4.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 5 m long (μ = 0.1) and then runs onto a spring (k = 2500 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 1 kgh = 4.5 mL = 5 mμ = 0.1k = 2500 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 4 kg projectile moving horizontally at 15 m/s explodes into two fragments that move along the same line. The 3 kg fragment continues forwards at 68 m/s. Find the velocity v′2 of the 1 kg fragment (positive in the original direction).
M = 4 kgu = 15 m/sm1 = 3 kgv′1 = 68 m/sm2 = 1 kg
v′2 = m/s
10.Momentum & collisionsHard
A 0.6 kg ball hits a wall at 18 m/s and bounces straight back at 15 m/s. The contact lasts 5 ms. Find the average force Favg of the wall on the ball.
m = 0.6 kgvin = 18 m/svout = 15 m/sΔt = 5 ms
Favg = N
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 3 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of seawater, with its top edge 3 m below the surface. Find the resultant hydrostatic force F on the gate.
Water flows through a horizontal pipe that narrows from 100 mm to 40 mm. In the wide section the pressure is 260 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 in the narrow section.
Water flows up through a pipe that narrows from 100 mm to 50 mm while rising 3 m. At section 1 the pressure is 210 kPa and the velocity is 0.75 m/s. Ignoring losses, find the pressure p2 at section 2.
A reversible refrigerator keeps a cold room at 4 °C by removing 9 kW of heat, and rejects heat to the surroundings at 25 °C. Find the rate Q̇H at which it rejects heat.
TL = 4 °CTH = 25 °CQ̇L = 9 kW
Q̇H = kW
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -18 °C in a kitchen at 25 °C, removing heat from the cold space at 3.5 kW. Find the minimum power input Ẇmin.
TH = 25 °CTL = -18 °CQ̇L = 3.5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
A small source sends sound equally in all directions. The level is 60 dB at 2 m from it. Find the level β2 at 8 m, ignoring absorption and reflections.
β1 = 60 dBr1 = 2 mr2 = 8 m
β2 = dB
20.Waves, sound & opticsHard
Two slits 0.15 mm apart are lit with monochromatic light. On a screen 1.5 m away, bright fringe number 3 lies 15 mm from the central fringe. Find the wavelength λ.
d = 0.15 mmL = 1.5 my3 = 15 mmm = 3
λ = nm
3Solutions
1.Kinematics
Answer: s = 24.11 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 13.89²/(2·4) = 24.11 m
Answer
s = 24.11 m
2.Kinematics
Answer: s = 566.3 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Top speed
v = a1·t1 = 1.5·10 = 15 m/s
Distance of each phase
s1 = ½·1.5·10² = 75 m
s2 = 15·29 = 435 m
s3 = 15²/(2·2) = 56.25 m
Total distance
s = 75 + 435 + 56.25 = 566.3 m
Answer
s = 566.3 m
3.Newton’s laws
Answer: F = 244.8 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Forces along the slope
Constant speed: the forces balance.
F = m·g·sin θ + μ·m·g·cos θ
Pushing force
F = 134.2 + 110.6 = 244.8 N
Answer
F = 244.8 N
4.Newton’s laws
Answer: a = 3.724 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·70/30² = 0.763
Angle
2θ = 49.73° → θ = 24.86°
Answer
θ = 24.86°
The other solution is 90° − θ = 65.14°.
6.Projectile motion
Answer: t = 5.626 s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 34·cos 45° = 24.04 m/s
vy = v0·sin θ = 34·sin 45° = 24.04 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 20 + 24.04·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (24.04 + √(578 + 392.4))/9.81 = 5.626 s
Answer
t = 5.626 s
7.Work & energy
Answer: d = 98.32 m
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Speed in base units
v = 100/3.6 = 27.78 m/s
Energy balance
½mv² = μmg·d → d = v²/(2μg) = 27.78²/(2·0.4·9.81) = 98.32 m
Answer
d = 98.32 m
Doubling the speed makes the stopping distance four times longer.
8.Work & energy
Answer: v = 8.859 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 9.81·(4.5 − 0.1·5) = 39.24 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·4) = 8.859 m/s
Answer
v = 8.859 m/s
9.Momentum & collisions
Answer: v′2 = −144 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 4·15 = 60 kg·m/s
Momentum after
60 = 3·68 + 1·v′2
v′2 = (60 − 204)/1 = −144 m/s
Answer
v′2 = −144 m/s
The minus sign means the second fragment flies backwards.
10.Momentum & collisions
Answer: Favg = 3960 N
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.6·(15 + 18) = 19.8 N·s
Average force
Favg = J/Δt = 19.8/0.005 = 3960 N
Answer
Favg = 3960 N
11.Hydrostatic force
Answer: F = 485.6 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 3/2 = 5.5 m
A = H·b = 3·3 = 9 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.5·9 = 485.6 kN
Answer
F = 485.6 kN
12.Hydrostatic force
Answer: F = 320.5 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2.5/2 = 4.25 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1025·9.81·4.25·7.5 = 320.5 kN
Answer
F = 320.5 kN
13.Continuity & Bernoulli
Answer: p2 = 163.7 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 25 + 273.15 = 298.1 K
TL = 4 + 273.15 = 277.1 K
Reversible heat ratio
Q̇H = Q̇L·TH/TL = 9·298.1/277.1 = 9.682 kW
Answer
Q̇H = 9.682 kW
Power input: Ẇ = 0.6819 kW.
18.Heat engines & refrigerators
Answer: Ẇmin = 0.5898 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 3.5/5.934 = 0.5898 kW
Answer
Ẇmin = 0.5898 kW
19.Waves, sound & optics
Answer: β2 = 47.96 dB
Waves: a periodic wave moves one wavelength in one period, so v = fλ with T = 1/f. On a stretched string v = √(T/μ), with T the tension and μ = m/L the mass per metre. Sound in air travels at about 343 m/s at 20 °C, light in vacuum at c = 3.00 × 10⁸ m/s. Loudness is measured on a logarithmic scale: β = 10·log₁₀(I/I₀) dB with I₀ = 10⁻¹² W/m², so 10 times the intensity adds 10 dB. A point source spreads its power P over a sphere: I = P/(4πr²).
Intensity ratio
I₂/I₁ = (2/8)² = 0.0625
New level
β₂ = 60 + 10·log₁₀(0.0625) = 47.96 dB
Answer
β2 = 47.96 dB
Every doubling of the distance lowers the level by about 6 dB.
20.Waves, sound & optics
Answer: λ = 500 nm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …