Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane needs a speed of 280 km/h to take off and the usable runway is 1800 m long. Starting from rest, what constant acceleration a does it need?
v₀ = 0v = 280 km/hs = 1800 m
a = m/s²
2.KinematicsHard
A model rocket is launched straight up from rest. Its engine gives it a constant upward acceleration of 32 m/s² for 1.5 s, after which the engine stops and the rocket moves freely. Ignore air resistance and use g = 9.81 m/s². How long after launch does it hit the ground? Find t.
a = 32 m/s²t1 = 1.5 sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 30 kg sled is pulled across level snow by a rope at 40° above the horizontal with a force of 160 N. The coefficient of kinetic friction is 0.4. Use g = 9.81 m/s². Find the acceleration a of the sled.
m = 30 kgF = 160 Nθ = 40°μ = 0.4g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A 5 kg block on a horizontal table is connected by a light string over a frictionless pulley to a hanging 2 kg mass. The table is frictionless. Use g = 9.81 m/s². Find the acceleration a of the system.
m1 = 5 kgm2 = 2 kgμ = 0g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched from level ground at 55° above the horizontal and lands 100 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 55°R = 100 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is launched at 45° above horizontal from the top of a 30 m cliff. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 23 m/sθ = 45°h = 30 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 1 kg block slides 3 m down a slope at 20° to the horizontal, with a coefficient of kinetic friction of 0.15. Find the work Wf done against friction.
m = 1 kgθ = 20°μ = 0.15d = 3 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 1 kg cart is released from rest at a height of 6 m on a smooth track that leads into a vertical circular loop of radius 2 m. Find the normal force N the track exerts on the cart at the top of the loop.
m = 1 kgh = 6 mR = 2 mg = 9.81 m/s²
N = N
9.Momentum & collisionsMedium
A 3.5 kg glider moving at 5 m/s makes a perfectly elastic head-on collision with a 1 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 3.5 kgm2 = 1 kgv1 = 5 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 26 m/s and bounces straight back at 5 m/s. The contact lasts 20 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.5 kgvin = 26 m/svout = 5 m/sΔt = 20 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 2 m wide sits in the wall of a tank of oil, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 3 mH = 1 mb = 2 mρ = 880 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
A pitot-static tube in a wind tunnel reads a difference of 500 Pa between the stagnation pressure and the static pressure. The air density is 1.2 kg/m³. Find the air speed v.
p0 − p = 500 Paρ = 1.2 kg/m³
v = m/s
14.Continuity & BernoulliHard
Water flows up through a pipe that narrows from 75 mm to 40 mm while rising 9 m. At section 1 the pressure is 320 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine receives heat from a source at 400 °C and rejects heat to the surroundings at 15 °C. Its actual thermal efficiency is 29%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 400 °CTL = 15 °Cη = 29%
ηII = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 5 °C in a kitchen at 32 °C, removing heat from the cold space at 4 kW. Find the highest possible coefficient of performance COPmax.
TH = 32 °CTL = 5 °CQ̇L = 4 kW
COPmax =
19.Waves, sound & opticsMedium
A pipe open at both ends is 0.5 m long. The speed of sound is 343 m/s. Find the frequency f1 of its fundamental (first harmonic).
v = 343 m/sn = 1L = 0.5 m
f1 = Hz
20.Waves, sound & opticsHard
Two slits 0.4 mm apart are lit with monochromatic light. On a screen 1 m away, bright fringe number 2 lies 2.66 mm from the central fringe. Find the wavelength λ.
d = 0.4 mmL = 1 my2 = 2.66 mmm = 2
λ = nm
3Solutions
1.Kinematics
Answer: a = 1.68 m/s²
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v = 280/3.6 = 77.78 m/s
Acceleration
a = v²/(2s) = 77.78²/(2·1800) = 1.68 m/s²
Answer
a = 1.68 m/s²
2.Kinematics
Answer: t = 11.99 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Powered phase
v₁ = 32·1.5 = 48 m/s
h₁ = ½·32·1.5² = 36 m
Free flight to the ground
Solve −h₁ = v₁·t₂ − ½·g·t₂² for the positive root.
t₂ = (48 + √(48² + 2·9.81·36))/9.81 = 10.49 s
t = 1.5 + 10.49 = 11.99 s
Answer
t = 11.99 s
3.Newton’s laws
Answer: a = 1.533 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Normal force
N = m·g − F·sin θ = 294.3 − 160·sin 40° = 191.5 N
Horizontal forces
m·a = F·cos θ − μ·N = 122.6 − 76.58
a = 45.99/30 = 1.533 m/s²
Answer
a = 1.533 m/s²
4.Newton’s laws
Answer: a = 2.803 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·100/sin 110°) = 32.31 m/s
Answer
v0 = 32.31 m/s
6.Projectile motion
Answer: x = 75.38 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 23·cos 45° = 16.26 m/s
vy = v0·sin θ = 23·sin 45° = 16.26 m/s
Time in the air
Solve y(t) = h + vy·t − ½gt² = 0 for the positive root.
0 = 30 + 16.26·t − 4.905·t²
t = (vy + √(vy² + 2gh))/g = (16.26 + √(264.5 + 588.6))/9.81 = 4.635 s
Horizontal distance
x = vx·t = 16.26·4.635 = 75.38 m
Answer
x = 75.38 m
7.Work & energy
Answer: Wf = 4.148 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 9.81·0.9397 = 9.218 N
F = μN = 0.15·9.218 = 1.383 N
Work against friction
Wf = F·d = 1.383·3 = 4.148 J
Answer
Wf = 4.148 J
8.Work & energy
Answer: N = 9.81 N
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). On a circular path the net force towards the centre must equal mv²/r.
Speed at the top
v² = 2g(h − 2R) = 2·9.81·(6 − 4) = 39.24 m²/s²
Forces at the top
m·g = 1·9.81 = 9.81 N
N = mv²/R − mg = 1·39.24/2 − 9.81 = 9.81 N
Answer
N = 9.81 N
The cart just makes it round when h = 2.5R; then N = 0 at the top.
9.Momentum & collisions
Answer: v′2 = 7.778 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (3.5 − 1)/(3.5 + 1)·5 = 2.778 m/s
v′2 = 2·3.5/(3.5 + 1)·5 = 7.778 m/s
Answer
v′2 = 7.778 m/s
10.Momentum & collisions
Answer: J = 15.5 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(5 + 26) = 15.5 N·s
Answer
J = 15.5 N·s
11.Hydrostatic force
Answer: F = 239.1 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2.5/2 = 3.25 m
A = H·b = 2.5·3 = 7.5 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3.25·7.5 = 239.1 kN
Answer
F = 239.1 kN
12.Hydrostatic force
Answer: ycp = 3.524 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 1/2 = 3.5 m
A = H·b = 1·2 = 2 m²
Resultant force
F = ρ·g·yc·A = 880·9.81·3.5·2 = 60.43 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Bernoulli to the stagnation point
The flow comes to rest at the tip, so its kinetic energy shows up as extra pressure.
p0 − p = ½ρv²
v = √(2·500/1.2) = 28.87 m/s
Answer
v = 28.87 m/s
14.Continuity & Bernoulli
Answer: p2 = 209 kPa
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 400 + 273.15 = 673.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηCarnot = 1 − 288.1/673.1 = 57.19 %
Second-law efficiency
ηII = η/ηCarnot = 29/57.19 = 50.7 %
Answer
ηII = 50.7 %
18.Heat engines & refrigerators
Answer: COPmax = 10.3
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Wavelength of this mode
λ = 2L/n = 2·0.5/1 = 1 m
Frequency
f = v/λ = 343/1 = 343 Hz
Answer
f1 = 343 Hz
20.Waves, sound & optics
Answer: λ = 532 nm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …