Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A plane starts from rest and accelerates uniformly at 3 m/s² along a runway. Find its speed v after 700 m.
v₀ = 0a = 3 m/s²s = 700 m
v = m/s
2.KinematicsHard
A ball is thrown straight up at 11 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². Find the greatest height hmax above the ground.
v₀ = 11 m/sh₀ = 25 mg = 9.81 m/s²
hmax = m
3.Newton’s lawsMedium
A 6 kg block slides down a frictionless slope at 25° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 6 kgθ = 25°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 25 N pulls the front 1 kg block; the 2 kg block is towed behind. The coefficient of kinetic friction is 0.2 for both blocks. Use g = 9.81 m/s². Find the acceleration a of the blocks.
m1 = 2 kgm2 = 1 kgF = 25 Nμ = 0.2g = 9.81 m/s²
a = m/s²
5.Projectile motionMedium
A ball is launched at 50° above horizontal from level ground. Ignore air resistance. Find the horizontal distance x travelled before the ball hits the ground.
v0 = 16 m/sθ = 50°g = 9.81 m/s²
x = m
6.Projectile motionHard
A ball is launched at 26 m/s and 60° above the horizontal from the top of a 55 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 26 m/sθ = 60°h = 55 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 1200 kg car drives up an 8° slope at a constant 54 km/h. Air resistance and rolling resistance together amount to 500 N. Find the power P the wheels must deliver, in kW.
A 5 kg block is released from rest at height 4.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4 m long (μ = 0.25) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 5 kgh = 4.5 mL = 4 mμ = 0.25k = 1000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 1.5 kg glider moving at 10 m/s makes a perfectly elastic head-on collision with a 4.5 kg glider at rest on a frictionless track. Find the velocity v′2 of the second glider after the collision.
m1 = 1.5 kgm2 = 4.5 kgv1 = 10 m/sv2 = 0
v′2 = m/s
10.Momentum & collisionsHard
A 0.55 kg ball hits a wall at 15 m/s and bounces straight back at 6 m/s. The contact lasts 25 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.55 kgvin = 15 m/svout = 6 m/sΔt = 25 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 4 mH = 3 mb = 1 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 3 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 1 mH = 1 mb = 3 mρ = 1000 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows through a horizontal venturi meter with an inlet diameter of 300 mm and a throat diameter of 150 mm. The pressure at the inlet is 31 kPa higher than at the throat. Ignoring losses, find the flow rate Q.
Water flows up through a pipe that narrows from 100 mm to 75 mm while rising 4 m. At section 1 the pressure is 370 kPa and the velocity is 2.25 m/s. Ignoring losses, find the pressure p2 at section 2.
A heat engine works between a hot reservoir at 625 °C and a cold reservoir at 15 °C. It takes in 2400 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 625 °CTL = 15 °CQH = 2400 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A Carnot heat engine receives 70 kW of heat from a source at 800 °C and rejects heat to the surroundings at 20 °C. All of its work drives a Carnot refrigerator that removes heat from a freezer at -25 °C and also rejects heat to the surroundings at 20 °C. Find the rate Q̇L at which heat is removed from the freezer.
TH = 800 °CT0 = 20 °CTL = -25 °CQ̇H = 70 kW
Q̇L = kW
19.Waves, sound & opticsMedium
An object stands 50 cm in front of a thin converging lens with a focal length of 30 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 50 cmf = 30 cm
di = cm
20.Waves, sound & opticsHard
An object is 40 cm in front of a concave mirror with a radius of curvature of 30 cm. Find the image distance di, positive for an image in front of the mirror (real) and negative for one behind it (virtual).
do = 40 cmR = 30 cm
di = cm
3Solutions
1.Kinematics
Answer: v = 64.81 m/s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Speed after the distance
v = √(2·a·s) = √(2·3·700) = 64.81 m/s
Answer
v = 64.81 m/s
(233.3 km/h)
2.Kinematics
Answer: hmax = 31.17 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Rise above the roof
0 = v₀² − 2·g·Δh → Δh = 11²/(2·9.81) = 6.167 m
Height above the ground
hmax = 25 + 6.167 = 31.17 m
Answer
hmax = 31.17 m
3.Newton’s laws
Answer: a = 4.146 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 16·cos 50° = 10.28 m/s
vy = v0·sin θ = 16·sin 50° = 12.26 m/s
Time in the air
Starting and landing at the same height: t = 2vy/g.
t = 2·12.26/9.81 = 2.499 s
Horizontal distance
x = vx·t = 10.28·2.499 = 25.7 m
Answer
x = 25.7 m
6.Projectile motion
Answer: H = 80.84 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 26·sin 60° = 22.52 m/s
Rise above the cliff
Δh = vy²/(2g) = 22.52²/(2·9.81) = 25.84 m
Height above the ground
H = 55 + 25.84 = 80.84 m
Answer
H = 80.84 m
7.Work & energy
Answer: P = 32.08 kW
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d). Power is force times speed: P = F·v.
Driving force
m·g = 1200·9.81 = 11772 N
mg·sin θ = 11772·sin 8° = 1638 N
F = 1638 + 500 = 2138 N
Power
v = 54/3.6 = 15 m/s
P = F·v = 2138·15 = 32075 W = 32.08 kW
Answer
P = 32.08 kW
8.Work & energy
Answer: v = 8.287 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 49.05·(4.5 − 0.25·4) = 171.7 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·3.5) = 8.287 m/s
Answer
v = 8.287 m/s
9.Momentum & collisions
Answer: v′2 = 5 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (1.5 − 4.5)/(1.5 + 4.5)·10 = −5 m/s
v′2 = 2·1.5/(1.5 + 4.5)·10 = 5 m/s
Answer
v′2 = 5 m/s
10.Momentum & collisions
Answer: J = 11.55 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.55·(6 + 15) = 11.55 N·s
Answer
J = 11.55 N·s
11.Hydrostatic force
Answer: F = 161.9 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 3/2 = 5.5 m
A = H·b = 3·1 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·5.5·3 = 161.9 kN
Answer
F = 161.9 kN
12.Hydrostatic force
Answer: ycp = 1.556 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 1/2 = 1.5 m
A = H·b = 1·3 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·1.5·3 = 44.15 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity
v1 = v2·(150/300)² = 0.25·v2
Bernoulli between inlet and throat
The pipe is horizontal, so only pressure and velocity change.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 293.1 K, T2 = 383.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 20·(250/450)·(383.1/293.1) = 14.52 L
Answer
V2 = 14.52 L
17.Heat engines & refrigerators
Answer: Wmax = 1630 kJ
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 625 + 273.15 = 898.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/898.1 = 67.92 %
Maximum work
Wmax = ηmax·QH = 0.6792·2400 = 1630 kJ
Answer
Wmax = 1630 kJ
18.Heat engines & refrigerators
Answer: Q̇L = 280.6 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 800 + 273.15 = 1073 K
T0 = 20 + 273.15 = 293.1 K
TL = -25 + 273.15 = 248.1 K
Engine work
η = 1 − 293.1/1073 = 0.7268
Ẇ = 0.7268·70 = 50.88 kW
Heat removed by the refrigerator
COPR = 248.1/(293.1 − 248.1) = 5.514
Q̇L = 5.514·50.88 = 280.6 kW
Answer
Q̇L = 280.6 kW
19.Waves, sound & optics
Answer: di = 75 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/30 − 1/50
di = 75 cm
Ray diagram
real, on the far side of the lens
Answer
di = 75 cm
20.Waves, sound & optics
Answer: di = 24 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.