Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 120 km/h brakes with a constant deceleration of 5.5 m/s² until it stops. How long does braking take? Find t.
v₀ = 120 km/ha = −5.5 m/s²v = 0
t = s
2.KinematicsHard
Ball A is dropped from rest from a height of 25 m. At the same instant ball B is thrown straight up from the ground directly below at 19 m/s. Ignore air resistance and use g = 9.81 m/s². When do the balls meet? Find t.
H = 25 mv0B = 19 m/sg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A box slides across a level floor with an initial speed of 11.5 m/s and comes to rest after 27 m. Use g = 9.81 m/s². Find the coefficient of kinetic friction μ.
v₀ = 11.5 m/sd = 27 mg = 9.81 m/s²
μ =
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 30 N pulls the front 12 kg block; the 2 kg block is towed behind. The coefficient of kinetic friction is 0.1 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 2 kgm2 = 12 kgF = 30 Nμ = 0.1g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 22 m/s and must land 35 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 22 m/sR = 35 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 17 m/s and 15° above the horizontal from the top of a 20 m cliff. Ignore air resistance and use g = 9.81 m/s². At what angle α below the horizontal does it hit the ground?
v₀ = 17 m/sθ = 15°h = 20 mg = 9.81 m/s²
α = °
7.Work & energyMedium
A 5 kg block slides 13 m down a slope at 45° to the horizontal, with a coefficient of kinetic friction of 0.2. Find the work Wf done against friction.
m = 5 kgθ = 45°μ = 0.2d = 13 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 2 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 2.5 m long (μ = 0.1) and then runs onto a spring (k = 2000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 2 kgh = 5 mL = 2.5 mμ = 0.1k = 2000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 600 kg car moving at 15 m/s runs into a stationary 1800 kg car and the two lock together. What percentage ΔK/K of the original kinetic energy is lost?
m1 = 600 kgv1 = 15 m/sm2 = 1800 kgv2 = 0
ΔK/K = %
10.Momentum & collisionsHard
A 1200 kg car runs into a parked 1700 kg car. The wrecks lock together and skid 19 m before stopping. The coefficient of kinetic friction between tyres and road is 0.7. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 2 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1 m wide sits in the wall of a tank of seawater, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
d = 4 mH = 1 mb = 1 mρ = 1025 kg/m³g = 9.81 m/s²
ycp = m
13.Continuity & BernoulliMedium
Water flows at 17 L/s through a horizontal pipe that narrows from 150 mm to 100 mm. The pressure in the narrow section is 270 kPa. Ignoring losses, find the pressure p1 in the wide section.
A hose with an inner diameter of 40 mm siphons water from an open tank. The highest point C of the hose is 3 m above the water surface, and the outlet (open to the air) is 2.5 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 40 mmzC = +3 mz2 = −2.5 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
What volume V does 10 g of N₂ occupy at 200 kPa and 60 °C? Treat it as an ideal gas.
A heat engine works between a hot reservoir at 225 °C and a cold reservoir at 35 °C. It takes in 600 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 225 °CTL = 35 °CQH = 600 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 2 °C in a kitchen at 32 °C, removing heat from the cold space at 0.5 kW. Find the minimum power input Ẇmin.
TH = 32 °CTL = 2 °CQ̇L = 0.5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 30 cm in front of a thin converging lens with a focal length of 10 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 30 cmf = 10 cm
di = cm
20.Waves, sound & opticsHard
Light of wavelength 500 nm falls on two slits 0.2 mm apart. The screen is 3 m away. Find the distance y3 from the central bright fringe to bright fringe number 3.
λ = 500 nmd = 0.2 mmL = 3 mm = 3
y3 = mm
3Solutions
1.Kinematics
Answer: t = 6.061 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 120/3.6 = 33.33 m/s
Braking time
0 = v₀ − a·t → t = v₀/a = 33.33/5.5 = 6.061 s
Answer
t = 6.061 s
2.Kinematics
Answer: t = 1.316 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Meeting time
Up is positive, the ground is y = 0.
25 − ½g·t² = 19·t − ½g·t² → t = 25/19 = 1.316 s
Answer
t = 1.316 s
3.Newton’s laws
Answer: μ = 0.2497
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
a = v₀²/(2d) = 11.5²/(2·27) = 2.449 m/s²
Friction coefficient
μ·m·g = m·a → μ = a/g = 2.449/9.81 = 0.2497
Answer
μ = 0.2497
4.Newton’s laws
Answer: T = 4.286 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: θ = 22.59 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·35/22² = 0.7094
Angle
2θ = 45.19° → θ = 22.59°
Answer
θ = 22.59°
The other solution is 90° − θ = 67.41°.
6.Projectile motion
Answer: α = 51.02 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 17·cos 15° = 16.42 m/s
vy0 = 17·sin 15° = 4.4 m/s
Vertical speed at impact
Energy or v² = v₀² + 2as in the vertical direction.
vy = √(4.4² + 2·9.81·20) = 20.29 m/s
Impact angle
tan α = vy/vx = 20.29/16.42 → α = 51.02°
Answer
α = 51.02°
7.Work & energy
Answer: Wf = 90.18 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 49.05·0.7071 = 34.68 N
F = μN = 0.2·34.68 = 6.937 N
Work against friction
Wf = F·d = 6.937·13 = 90.18 J
Answer
Wf = 90.18 J
8.Work & energy
Answer: v = 9.654 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(5 − 0.1·2.5) = 93.2 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·4.75) = 9.654 m/s
Answer
v = 9.654 m/s
9.Momentum & collisions
Answer: ΔK/K = 75 %
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 600·15/2400 = 3.75 m/s
Kinetic energy before and after
Kbefore = ½·600·15² = 67500 J
Kafter = ½·2400·3.75² = 16875 J
Fraction lost
ΔK/K = 50625/67500 = 75 %
Answer
ΔK/K = 75 %
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: v1 = 39.04 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 225 + 273.15 = 498.1 K
TL = 35 + 273.15 = 308.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 308.1/498.1 = 38.14 %
Maximum work
Wmax = ηmax·QH = 0.3814·600 = 228.8 kJ
Answer
Wmax = 228.8 kJ
18.Heat engines & refrigerators
Answer: Ẇmin = 0.05452 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 0.5/9.172 = 0.05452 kW
Answer
Ẇmin = 0.05452 kW
19.Waves, sound & optics
Answer: di = 15 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/10 − 1/30
di = 15 cm
Ray diagram
real, on the far side of the lens
Answer
di = 15 cm
20.Waves, sound & optics
Answer: y3 = 22.5 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …