Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car speeding at a constant 27 m/s passes a police car standing still. At that moment the police car starts and accelerates uniformly at 3.5 m/s². How far from its starting point does the police car catch up? Find d.
vcar = 27 m/sapolice = 3.5 m/s²v0,police = 0
d = m
2.KinematicsHard
A ball is thrown straight up at 15 m/s from the edge of a roof 20 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 15 m/sh₀ = 20 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
Masses of 9 kg and 7 kg hang on either side of a light, frictionless pulley, connected by a light string. The system is released from rest. Use g = 9.81 m/s². Find the acceleration a of the masses.
m1 = 9 kgm2 = 7 kgg = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 50 N pulls the front 2 kg block; the 8 kg block is towed behind. The coefficient of kinetic friction is 0.15 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 8 kgm2 = 2 kgF = 50 Nμ = 0.15g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched at 35° above horizontal from level ground. Ignore air resistance. Find the maximum height H the ball reaches.
v0 = 38 m/sθ = 35°g = 9.81 m/s²
H = m
6.Projectile motionHard
A ball is launched at 20 m/s and 55° above the horizontal from the top of a 50 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 20 m/sθ = 55°h = 50 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 2.5 kg block slides 13 m down a slope at 40° to the horizontal, with a coefficient of kinetic friction of 0.35. Find the work Wf done against friction.
m = 2.5 kgθ = 40°μ = 0.35d = 13 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 2 kg block is released from rest at height 3.5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4 m long (μ = 0.1) and then runs onto a spring (k = 1500 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 2 kgh = 3.5 mL = 4 mμ = 0.1k = 1500 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 12 kg projectile moving horizontally at 32 m/s explodes into two fragments that move along the same line. The 3 kg fragment continues forwards at 44 m/s. Find the velocity v′2 of the 9 kg fragment (positive in the original direction).
M = 12 kgu = 32 m/sm1 = 3 kgv′1 = 44 m/sm2 = 9 kg
v′2 = m/s
10.Momentum & collisionsHard
A 1700 kg car runs into a parked 1000 kg car. The wrecks lock together and skid 8 m before stopping. The coefficient of kinetic friction between tyres and road is 0.75. Use g = 9.81 m/s². Find the speed v1 of the first car just before the collision.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 4 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 2.5 m below the surface. Find the resultant hydrostatic force F on the gate.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 50 mm. The water level is kept 5 m above the orifice and the discharge coefficient is 0.64. Find the flow rate Q. Use g = 9.81 m/s².
d = 50 mmh = 5 mCd = 0.64g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A horizontal venturi meter (inlet 80 mm, throat 40 mm) carries water. A mercury U-tube manometer connected between the inlet and the throat shows a level difference of 310 mm. The discharge coefficient is 0.98. Find the flow rate Q. Use ρ = 1000 kg/m³ for water, 13 600 kg/m³ for mercury and g = 9.81 m/s².
A heat engine works between a hot reservoir at 450 °C and a cold reservoir at 15 °C. Find the highest possible thermal efficiency ηmax.
TH = 450 °CTL = 15 °C
ηmax = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at -18 °C in a kitchen at 25 °C, removing heat from the cold space at 0.5 kW. Find the highest possible coefficient of performance COPmax.
TH = 25 °CTL = -18 °CQ̇L = 0.5 kW
COPmax =
19.Waves, sound & opticsMedium
A source of 1200 Hz moving at 30 m/s and an observer moving at 10 m/s approach each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 1200 Hzv = 343 m/svs = 30 m/svo = 10 m/s
f′ = Hz
20.Waves, sound & opticsHard
Two thin lenses share an axis, 60 cm apart: lens 1 with f₁ = 8 cm and lens 2 with f₂ = 12 cm. An object stands 15 cm in front of lens 1. Find the position di2 of the final image measured from lens 2 (positive beyond lens 2, real-is-positive convention).
f1 = 8 cmf2 = 12 cms = 60 cmdo = 15 cm
di2 = cm
3Solutions
1.Kinematics
Answer: d = 416.6 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equal distances
v·t = ½·a·t² → t = 2v/a = 2·27/3.5 = 15.43 s
Distance
d = v·t = 27·15.43 = 416.6 m
Answer
d = 416.6 m
At that moment the police car moves at 2v = 54 m/s.
2.Kinematics
Answer: t = 4.062 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−20 = 15·t − ½·9.81·t²
4.905·t² − 15·t − 20 = 0
Solve the quadratic
Only the positive root is physical.
t = (15 + √(15² + 2·9.81·20))/9.81 = 4.062 s
Answer
t = 4.062 s
3.Newton’s laws
Answer: a = 1.226 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Acceleration
The net driving force is the difference of the weights; it moves the total mass.
a = (9 − 7)·9.81/(9 + 7) = 1.226 m/s²
Answer
a = 1.226 m/s²
4.Newton’s laws
Answer: T = 40 N
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: H = 24.21 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
Horizontal velocity stays constant; vertical motion has a constant acceleration g = 9.81 m/s² downward.
vx = v0·cos θ = 38·cos 35° = 31.13 m/s
vy = v0·sin θ = 38·sin 35° = 21.8 m/s
Highest point
At the top the vertical velocity is zero: vy² = 2gH.
H = vy²/(2g) = 21.8²/(2·9.81) = 24.21 m
Answer
H = 24.21 m
6.Projectile motion
Answer: H = 63.68 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 20·sin 55° = 16.38 m/s
Rise above the cliff
Δh = vy²/(2g) = 16.38²/(2·9.81) = 13.68 m
Height above the ground
H = 50 + 13.68 = 63.68 m
Answer
H = 63.68 m
7.Work & energy
Answer: Wf = 85.48 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 24.53·0.766 = 18.79 N
F = μN = 0.35·18.79 = 6.576 N
Work against friction
Wf = F·d = 6.576·13 = 85.48 J
Answer
Wf = 85.48 J
8.Work & energy
Answer: v = 7.799 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 19.62·(3.5 − 0.1·4) = 60.82 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·3.1) = 7.799 m/s
Answer
v = 7.799 m/s
9.Momentum & collisions
Answer: v′2 = 28 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Momentum before
p = M·u = 12·32 = 384 kg·m/s
Momentum after
384 = 3·44 + 9·v′2
v′2 = (384 − 132)/9 = 28 m/s
Answer
v′2 = 28 m/s
10.Momentum & collisions
Answer: v1 = 17.23 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 1.5/2 = 4.75 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·4.75·2.25 = 104.8 kN
Answer
F = 104.8 kN
12.Hydrostatic force
Answer: F = 90.39 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2.5 + 1.5/2 = 3.25 m
A = H·b = 1.5·1.5 = 2.25 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·3.25·2.25 = 90.39 kN
Answer
F = 90.39 kN
13.Continuity & Bernoulli
Answer: Q = 12.45 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·5) = 9.905 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Pressure difference from the manometer
Δp = (13600 − 1000)·9.81·0.31 = 38318 Pa
Throat velocity
Continuity and Bernoulli together give the ideal throat velocity.
Combined gas law: for a fixed amount of ideal gas, P1V1/T1 = P2V2/T2.
Absolute temperatures
T1 = 303.1 K, T2 = 393.1 K
Combined gas law
V2 = V1·(P1/P2)·(T2/T1) = 10·(350/650)·(393.1/303.1) = 6.983 L
Answer
V2 = 6.983 L
17.Heat engines & refrigerators
Answer: ηmax = 60.15 %
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 450 + 273.15 = 723.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/723.1 = 60.15 %
Answer
ηmax = 60.15 %
18.Heat engines & refrigerators
Answer: COPmax = 5.934
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.