Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A driver moving at 50 km/h sees an obstacle. Her reaction time is 0.5 s, after which the car brakes with a constant deceleration of 6 m/s². Find the total stopping distance d from the moment she sees the obstacle.
v₀ = 50 km/htr = 0.5 sa = −6 m/s²
d = m
2.KinematicsHard
A ball is thrown straight up at 9 m/s from the edge of a roof 25 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 9 m/sh₀ = 25 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
An 8 kg block slides down a frictionless slope at 45° to the horizontal. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 8 kgθ = 45°μ = 0g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
Two blocks on a level floor are joined by a light horizontal string. A horizontal force of 80 N pulls the front 12 kg block; the 9 kg block is towed behind. The coefficient of kinetic friction is 0.3 for both blocks. Use g = 9.81 m/s². Find the tension T in the connecting string.
m1 = 9 kgm2 = 12 kgF = 80 Nμ = 0.3g = 9.81 m/s²
T = N
5.Projectile motionMedium
A ball is launched from level ground at 45° above the horizontal and lands 65 m away. Ignore air resistance and use g = 9.81 m/s². Find the launch speed v0.
θ = 45°R = 65 mg = 9.81 m/s²
v0 = m/s
6.Projectile motionHard
A ball is thrown from ground level at 39 m/s and 70° above the horizontal. It lands on the flat roof of a building 16 m high, on its way down. Ignore air resistance and use g = 9.81 m/s². Find the horizontal distance x from the launch point to where it lands.
v₀ = 39 m/sθ = 70°hroof = 16 mg = 9.81 m/s²
x = m
7.Work & energyMedium
A 4 kg block slides 15 m down a slope at 25° to the horizontal, with a coefficient of kinetic friction of 0.3. Find the work Wf done against friction.
m = 4 kgθ = 25°μ = 0.3d = 15 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 4 kg block is released from rest at height 5 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 4 m long (μ = 0.3) and then runs onto a spring (k = 1000 N/m) on a smooth surface. Find the speed v of the block when it reaches the spring.
m = 4 kgh = 5 mL = 4 mμ = 0.3k = 1000 N/mg = 9.81 m/s²
v = m/s
9.Momentum & collisionsMedium
A 2 kg glider moving at 11 m/s makes a perfectly elastic head-on collision with a 1.5 kg glider at rest on a frictionless track. Find the velocity v′1 of the first glider after the collision (positive in its original direction).
m1 = 2 kgm2 = 1.5 kgv1 = 11 m/sv2 = 0
v′1 = m/s
10.Momentum & collisionsHard
A 0.35 kg ball hits a wall at 15 m/s and bounces straight back at 15 m/s. The contact lasts 10 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.35 kgvin = 15 m/svout = 15 m/sΔt = 10 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 2 m wide sits in the wall of a tank of water, with its top edge 1 m below the surface. Find the resultant hydrostatic force F on the gate.
d = 1 mH = 3 mb = 2 mρ = 1000 kg/m³g = 9.81 m/s²
F = kN
12.Hydrostatic forceHard
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 4 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water drains from a large open tank through a sharp-edged orifice with a diameter of 50 mm. The water level is kept 4.5 m above the orifice and the discharge coefficient is 0.61. Find the flow rate Q. Use g = 9.81 m/s².
d = 50 mmh = 4.5 mCd = 0.61g = 9.81 m/s²
Q = L/s
14.Continuity & BernoulliHard
A hose with an inner diameter of 40 mm siphons water from an open tank. The highest point C of the hose is 2.5 m above the water surface, and the outlet (open to the air) is 4 m below the water surface. Ignore losses and take g = 9.81 m/s². Find the flow rate Q.
d = 40 mmzC = +2.5 mz2 = −4 mg = 9.81 m/s²
Q = L/s
15.Ideal gas lawMedium
A tank of 50 L contains 240 g of CO₂ at 5 °C. Treat it as an ideal gas and find the pressure P.
A heat engine works between a hot reservoir at 550 °C and a cold reservoir at 15 °C. It takes in 600 kJ of heat. Find the most work Wmax it could possibly produce.
TH = 550 °CTL = 15 °CQH = 600 kJ
Wmax = kJ
18.Heat engines & refrigeratorsHard
A heat pump delivers 5.5 kW of heat to a heating system at 22 °C, taking heat from a source at 5 °C. Its actual COP is 35% of the Carnot COP between these temperatures. Find the electrical power Ẇ it uses.
TH = 22 °CTL = 5 °CηII = 35%Q̇H = 5.5 kW
Ẇ = kW
19.Waves, sound & opticsMedium
A source of 1000 Hz moving at 20 m/s and an observer moving at 15 m/s approach each other. The speed of sound is 343 m/s. Find the frequency f′ that the observer hears.
f = 1000 Hzv = 343 m/svs = 20 m/svo = 15 m/s
f′ = Hz
20.Waves, sound & opticsHard
Light of wavelength 480 nm falls on two slits 0.5 mm apart. The screen is 1 m away. Find the distance y3 from the central bright fringe to bright fringe number 3.
λ = 480 nmd = 0.5 mmL = 1 mm = 3
y3 = mm
3Solutions
1.Kinematics
Answer: d = 23.02 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 50/3.6 = 13.89 m/s
Reaction distance
d1 = v₀·tr = 13.89·0.5 = 6.944 m
Braking distance
d2 = v₀²/(2a) = 13.89²/(2·6) = 16.08 m
Total
d = 6.944 + 16.08 = 23.02 m
Answer
d = 23.02 m
2.Kinematics
Answer: t = 3.354 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−25 = 9·t − ½·9.81·t²
4.905·t² − 9·t − 25 = 0
Solve the quadratic
Only the positive root is physical.
t = (9 + √(9² + 2·9.81·25))/9.81 = 3.354 s
Answer
t = 3.354 s
3.Newton’s laws
Answer: a = 6.937 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
With the same μ on both blocks, friction drops out: T = F·m₁/(m₁ + m₂).
5.Projectile motion
Answer: v0 = 25.25 m/s
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Solve the range formula for v₀
v₀ = √(g·R/sin 2θ) = √(9.81·65/sin 90°) = 25.25 m/s
Answer
v0 = 25.25 m/s
6.Projectile motion
Answer: x = 93.45 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Split the launch velocity
vx = 13.34 m/s, vy = 36.65 m/s
Time to land on the roof
Larger root: the ball is descending.
16 = 36.65·t − 4.905·t²
t = (36.65 + √(36.65² − 2·9.81·16))/9.81 = 7.006 s
Horizontal distance
x = vx·t = 13.34·7.006 = 93.45 m
Answer
x = 93.45 m
7.Work & energy
Answer: Wf = 160 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 39.24·0.9063 = 35.56 N
F = μN = 0.3·35.56 = 10.67 N
Work against friction
Wf = F·d = 10.67·15 = 160 J
Answer
Wf = 160 J
8.Work & energy
Answer: v = 8.635 m/s
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 39.24·(5 − 0.3·4) = 149.1 J
Speed at the spring
½mv² = mg(h − μL) → v = √(2g(h − μL)) = √(2·9.81·3.8) = 8.635 m/s
Answer
v = 8.635 m/s
9.Momentum & collisions
Answer: v′1 = 1.571 m/s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Elastic collision with a target at rest
Solving momentum and energy conservation together gives these two results.
v′1 = (2 − 1.5)/(2 + 1.5)·11 = 1.571 m/s
v′2 = 2·2/(2 + 1.5)·11 = 12.57 m/s
Answer
v′1 = 1.571 m/s
10.Momentum & collisions
Answer: J = 10.5 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.35·(15 + 15) = 10.5 N·s
Answer
J = 10.5 N·s
11.Hydrostatic force
Answer: F = 147.2 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 1 + 3/2 = 2.5 m
A = H·b = 3·2 = 6 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·2.5·6 = 147.2 kN
Answer
F = 147.2 kN
12.Hydrostatic force
Answer: ycp = 5.349 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 4 + 2.5/2 = 5.25 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·5.25·3.75 = 243.3 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Ideal jet velocity
√(2gh) = √(2·9.81·4.5) = 9.396 m/s
Actual flow rate
The discharge coefficient accounts for the contraction of the jet and friction at the edge.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Velocity in the hose
Surface and outlet are both open to the air, so the pressure terms cancel.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 550 + 273.15 = 823.1 K
TL = 15 + 273.15 = 288.1 K
Carnot efficiency
ηmax = 1 − TL/TH = 1 − 288.1/823.1 = 64.99 %
Maximum work
Wmax = ηmax·QH = 0.6499·600 = 390 kJ
Answer
Wmax = 390 kJ
18.Heat engines & refrigerators
Answer: Ẇ = 0.9051 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 22 + 273.15 = 295.1 K
TL = 5 + 273.15 = 278.1 K
Carnot and actual COP
COPmax = 295.1/(295.1 − 278.1) = 17.36
COP = 0.35·17.36 = 6.077
Power input
Ẇ = Q̇H/COP = 5.5/6.077 = 0.9051 kW
Answer
Ẇ = 0.9051 kW
19.Waves, sound & optics
Answer: f′ = 1108 Hz
Standing waves and the Doppler effect: a string fixed at both ends, or a pipe open at both ends, fits whole half-wavelengths: L = nλ/2, fn = n·v/(2L), n = 1, 2, 3, … A pipe closed at one end has a node at the closed end and an antinode at the open end: L = nλ/4 with odd n only, fn = n·v/(4L). When source or observer move along the line between them, f′ = f·(v ± vo)/(v ∓ vs): use the upper signs for motion towards each other. Two waves of nearly equal frequency beat at |f₁ − f₂|.
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …