Convert units: nm, mm and cm to m, and check whether angles are measured from the normal.
Check signs and plausibility: a virtual image has dᵢ < 0, an approaching source sounds higher, a closed pipe has only odd harmonics.
2Practice problems
1.KinematicsMedium
A car driving at 108 km/h brakes with a constant deceleration of 4.5 m/s² until it stops. Find the braking distance s.
v₀ = 108 km/ha = −4.5 m/s²v = 0
s = m
2.KinematicsHard
A ball is thrown straight up at 9 m/s from the edge of a roof 5 m above the ground. Ignore air resistance and use g = 9.81 m/s². How long after the throw does it hit the ground? Find t.
v₀ = 9 m/sh₀ = 5 mg = 9.81 m/s²
t = s
3.Newton’s lawsMedium
A 10 kg block slides down a slope at 30° to the horizontal. The coefficient of kinetic friction is 0.15. Use g = 9.81 m/s². Find the acceleration a of the block along the slope.
m = 10 kgθ = 30°μ = 0.15g = 9.81 m/s²
a = m/s²
4.Newton’s lawsHard
A block is given a push so that it starts sliding up a ramp at 15° with a speed of 9 m/s. The coefficient of kinetic friction is 0.25. Use g = 9.81 m/s². How far d along the ramp does it slide before it stops?
v₀ = 9 m/sθ = 15°μ = 0.25g = 9.81 m/s²
d = m
5.Projectile motionMedium
A ball is launched from level ground at 24 m/s and must land 25 m away. Ignore air resistance and use g = 9.81 m/s². Find the smaller of the two possible launch angles θ.
v₀ = 24 m/sR = 25 mg = 9.81 m/s²
θ = °
6.Projectile motionHard
A ball is launched at 10 m/s and 30° above the horizontal from the top of a 15 m cliff. Ignore air resistance and use g = 9.81 m/s². Find the greatest height H above the ground at the foot of the cliff.
v₀ = 10 m/sθ = 30°h = 15 mg = 9.81 m/s²
H = m
7.Work & energyMedium
A 10 kg block slides 9 m down a slope at 25° to the horizontal, with a coefficient of kinetic friction of 0.35. Find the work Wf done against friction.
m = 10 kgθ = 25°μ = 0.35d = 9 mg = 9.81 m/s²
Wf = J
8.Work & energyHard
A 2.5 kg block is released from rest at height 3 m on a smooth ramp. At the bottom it crosses a rough horizontal strip 3.5 m long (μ = 0.2) and then runs onto a spring (k = 500 N/m) on a smooth surface. Find the maximum compression x of the spring.
m = 2.5 kgh = 3 mL = 3.5 mμ = 0.2k = 500 N/mg = 9.81 m/s²
x = cm
9.Momentum & collisionsMedium
A 1800 kg car moving at 16 m/s runs into a stationary 1600 kg car and the two lock together. How much kinetic energy ΔK is lost in the collision?
m1 = 1800 kgv1 = 16 m/sm2 = 1600 kgv2 = 0
ΔK = J
10.Momentum & collisionsHard
A 0.5 kg ball hits a wall at 29 m/s and bounces straight back at 8 m/s. The contact lasts 10 ms. Find the magnitude of the impulse J the wall gives the ball.
m = 0.5 kgvin = 29 m/svout = 8 m/sΔt = 10 ms
J = N·s
11.Hydrostatic forceMedium
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of water, with its top edge 2 m below the surface. Find the resultant hydrostatic force F on the gate.
A vertical rectangular gate 1.5 m wide sits in the wall of a tank of glycerin, with its top edge 3 m below the surface. Find the depth ycp of the centre of pressure below the surface.
Water flows through a horizontal pipe that narrows from 100 mm to 50 mm. In the wide section the pressure is 290 kPa and the velocity is 2 m/s. Ignoring losses, find the pressure p2 in the narrow section.
A closed water tank has compressed air above the water at a gauge pressure of 80 kPa. Water leaves through an opening with a diameter of 40 mm, 5 m below the water surface, into the open air. Ignoring losses, find the flow rate Q. Use g = 9.81 m/s².
A heat engine receives heat from a source at 850 °C and rejects heat to the surroundings at 10 °C. Its actual thermal efficiency is 41%. Find its second-law efficiency ηII, the ratio of the actual efficiency to the Carnot efficiency.
TH = 850 °CTL = 10 °Cη = 41%
ηII = %
18.Heat engines & refrigeratorsHard
A refrigerator keeps its cold space at 2 °C in a kitchen at 25 °C, removing heat from the cold space at 4.5 kW. Find the minimum power input Ẇmin.
TH = 25 °CTL = 2 °CQ̇L = 4.5 kW
Ẇmin = kW
19.Waves, sound & opticsMedium
An object stands 25 cm in front of a thin converging lens with a focal length of 5 cm. Find the image distance di. Use the sign convention 1/f = 1/do + 1/di (f < 0 for a diverging lens, di < 0 for a virtual image).
do = 25 cmf = 5 cm
di = cm
20.Waves, sound & opticsHard
Light of wavelength 633 nm passes through a single slit 0.1 mm wide. Find the width w of the central bright maximum on a screen 2 m away (between the first dark fringes on either side).
λ = 633 nma = 0.1 mmL = 2 m
w = mm
3Solutions
1.Kinematics
Answer: s = 100 m
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Units
v₀ = 108/3.6 = 30 m/s
Braking distance
0 = v₀² − 2·a·s → s = v₀²/(2a) = 30²/(2·4.5) = 100 m
Answer
s = 100 m
2.Kinematics
Answer: t = 2.282 s
Motion with constant acceleration: v = v₀ + a·t, s = v₀·t + ½·a·t² and v² = v₀² + 2·a·s. Pick the equation that contains the three things you know and the one you want, and keep the signs consistent with one positive direction.
Equation of motion
Up is positive and the ground is h₀ below the starting point.
−5 = 9·t − ½·9.81·t²
4.905·t² − 9·t − 5 = 0
Solve the quadratic
Only the positive root is physical.
t = (9 + √(9² + 2·9.81·5))/9.81 = 2.282 s
Answer
t = 2.282 s
3.Newton’s laws
Answer: a = 3.631 m/s²
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Newton’s second law: the net force on a body equals its mass times its acceleration, ΣF = m·a. Draw a free-body diagram, choose a positive direction along the motion, and add every force in that direction: applied forces, friction μ·N against the motion, and the components of gravity.
Deceleration
Both forces point down the slope; the mass cancels.
a = 9.81·(sin 15° + 0.25·cos 15°) = 4.908 m/s²
Distance
d = v₀²/(2a) = 9²/(2·4.908) = 8.252 m
Answer
d = 8.252 m
5.Projectile motion
Answer: θ = 12.6 °
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Range formula
R = v₀²·sin 2θ/g → sin 2θ = 9.81·25/24² = 0.4258
Angle
2θ = 25.2° → θ = 12.6°
Answer
θ = 12.6°
The other solution is 90° − θ = 77.4°.
6.Projectile motion
Answer: H = 16.27 m
Projectile motion: with no air resistance, x = vxt and y = h + vyt − ½gt². The two directions are independent except that they share the same time.
Vertical launch speed
vy = 10·sin 30° = 5 m/s
Rise above the cliff
Δh = vy²/(2g) = 5²/(2·9.81) = 1.274 m
Height above the ground
H = 15 + 1.274 = 16.27 m
Answer
H = 16.27 m
7.Work & energy
Answer: Wf = 280.1 J
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Friction force
N = mg·cos θ = 98.1·0.9063 = 88.91 N
F = μN = 0.35·88.91 = 31.12 N
Work against friction
Wf = F·d = 31.12·9 = 280.1 J
Answer
Wf = 280.1 J
8.Work & energy
Answer: x = 47.5 cm
Work–energy principle: the change in kinetic energy equals the work done by all forces. Writing gravity and springs as potential energy (mgh and ½kx²) turns this into a balance: initial energy = final energy + energy lost to friction (μN·d).
Energy left after the rough strip
The ramp is smooth, so only the strip removes energy.
mgh − μmgL = 24.53·(3 − 0.2·3.5) = 56.41 J
Maximum compression
½kx² = 56.41 → x = √(2·56.41/500) = 0.475 m = 47.5 cm
Answer
x = 47.5 cm
9.Momentum & collisions
Answer: ΔK = 108424 J
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Common velocity
v′ = m1·v1/(m1 + m2) = 1800·16/3400 = 8.471 m/s
Kinetic energy before and after
Kbefore = ½·1800·16² = 230400 J
Kafter = ½·3400·8.471² = 121976 J
Energy lost
ΔK = 230400 − 121976 = 108424 J
Answer
ΔK = 108424 J
The lost energy goes into deformation, heat and sound.
10.Momentum & collisions
Answer: J = 18.5 N·s
Conservation of momentum: when no external force acts during a collision, the total momentum Σm·v before equals the total after. Velocities have a direction, so pick a positive direction and give velocities the other way a minus sign. In an elastic collision kinetic energy is conserved too; in a perfectly inelastic one the bodies stick together.
Change in momentum
J = m·Δv = 0.5·(8 + 29) = 18.5 N·s
Answer
J = 18.5 N·s
11.Hydrostatic force
Answer: F = 88.29 kN
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 2 + 2/2 = 3 m
A = H·b = 2·1.5 = 3 m²
Resultant force
F = ρ·g·yc·A = 1000·9.81·3·3 = 88.29 kN
Answer
F = 88.29 kN
12.Hydrostatic force
Answer: ycp = 4.373 m
Hydrostatic force on a plane surface: F = ρ·g·yc·A. It acts at the centre of pressure, ycp = yc + Ic/(ycA), which always lies below the centroid.
Centroid depth and area
yc = d + H/2 = 3 + 2.5/2 = 4.25 m
A = H·b = 2.5·1.5 = 3.75 m²
Resultant force
F = ρ·g·yc·A = 1260·9.81·4.25·3.75 = 197 kN
Centre of pressure
Pressure grows with depth, so the resultant acts below the centroid.
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Continuity and Bernoulli
Work in Pa, then divide by 1000 to get kPa.
v2 = v1·(d1/d2)² = 2·(100/50)² = 8 m/s
½ρ(v1² − v2²) = ½·1000·(2² − 8²)/1000 = −30 kPa
p2 = p1 + ½ρ(v1² − v2²) = 290 + (−30) = 260 kPa
Answer
p2 = 260 kPa
14.Continuity & Bernoulli
Answer: Q = 20.19 L/s
Continuity and Bernoulli: for an incompressible fluid the flow rate is the same at every section, Q = A₁v₁ = A₂v₂. Along a streamline without losses, p + ½ρv² + ρgz is constant, so where the fluid is faster or higher its pressure is lower.
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
Absolute temperatures
TH = 850 + 273.15 = 1123 K
TL = 10 + 273.15 = 283.1 K
Carnot efficiency
ηCarnot = 1 − 283.1/1123 = 74.79 %
Second-law efficiency
ηII = η/ηCarnot = 41/74.79 = 54.82 %
Answer
ηII = 54.82 %
18.Heat engines & refrigerators
Answer: Ẇmin = 0.3762 kW
Second-law limits: no cycle working between reservoirs at absolute temperatures TH and TL can beat the reversible (Carnot) cycle: ηmax = 1 − TL/TH, COPR,max = TL/(TH − TL) and COPHP,max = TH/(TH − TL). Energy is always conserved: QH = W + QL.
The least work is needed by a reversible machine, which has the highest COP.
Ẇmin = Q̇L/COP = 4.5/11.96 = 0.3762 kW
Answer
Ẇmin = 0.3762 kW
19.Waves, sound & optics
Answer: di = 6.25 cm
Geometric optics: at a boundary, n₁·sin θ₁ = n₂·sin θ₂ (Snell's law), with angles measured from the normal and n = c/v. Going into a slower medium the ray bends towards the normal. From a denser medium (n₁ > n₂) beyond the critical angle θc = arcsin(n₂/n₁) all light is reflected: total internal reflection. Thin lenses and spherical mirrors obey 1/f = 1/do + 1/di with the magnification m = −di/do. Sign convention: f > 0 for a converging lens and a concave mirror (f = R/2), f < 0 for a diverging lens and a convex mirror; di > 0 for a real image, di < 0 for a virtual one, and m < 0 for an inverted image.
Thin-lens equation
1/di = 1/f − 1/do = 1/5 − 1/25
di = 6.25 cm
Ray diagram
real, on the far side of the lens
Answer
di = 6.25 cm
20.Waves, sound & optics
Answer: w = 25.32 mm
Interference and diffraction: light from two slits a distance d apart reaches a point on the screen with a path difference d·sin θ. Bright fringes appear where d·sin θ = mλ (m = 0, ±1, ±2, …). For a screen at distance L ≫ d, the m-th bright fringe is at y = mλL/d and the fringe spacing is Δy = λL/d. A grating with N lines per millimetre has d = 1/N and sharp maxima at d·sin θ = mλ; since sin θ ≤ 1, the highest order is the largest whole number m ≤ d/λ. A single slit of width a has dark fringes at a·sin θ = mλ, m = ±1, ±2, …